Westamp Service & Repair Forum

dear sirswe have a colchester/master 600cnc lathe.its control system is crusader ii l anilam microprocesser control system.drive is indramat 3trm2.we bought it as a used mashie. control system dosent work.would you please help us how we can get its troublshooting plan and programming and operating instructions.looking forward to have your prompt answer best regards mr,niaraki

— Posted by niaraki on 2007-05-28

Reply🗨️Ask a New Question Below❓

If you need your Westamp unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 12 Comments

#Westamp by Syed Pervez Ali on 2006-02-15 07:45
I have one machine vertical mill Avon with crusader II anilam opertating panel.it is not in working position before to run it I want to check it servo drive cards with servo motors , I am 30 years experienced man of working in electronics and industerial equipments.these card are in very good condit...
Show More
➡️ Reply
#Westamp by SAUL on 2006-08-29 23:48
I NEED THE DIAGRAM OF CONECTION OF THE WESTAMP CARD AW 29947TO TEST THE CARD AND THE SIGNAL IS REQUIRE TO WORKTENKS
➡️ Reply
#Westamp by Adan Caldera on 2006-09-07 19:00
Hi, I need to kow what kind of transistor its 29794 because I have one servo drive that have this transistor damage its in short.Can you help me whit this pease,Thanks.
➡️ Reply
#Westamp by niaraki on 2007-05-28 07:07
dear sirswe have a colchester/master 600cnc lathe.its control system is crusader ii l anilam microprocesser control system.drive is indramat 3trm2.we bought it as a used mashie. control system dosent work.would you please help us how we can get its troublshooting plan and programming and operating i...
Show More
➡️ Reply
#Westamp by niaraki on 2007-05-28 07:09
dear sirswe have a colchester/master 600cnc lathe.its control system is crusader ii l anilam microprocesser control system.drive is indramat 3trm2.we bought it as a used mashie. control system dosent work.would you please help us how we can get its troublshooting plan and programming and operating i...
Show More
➡️ Reply
#Westamp by Andres Felipe Marmol Velez on 2007-11-30 14:32
Good morming, we are 2 Mechatronic Engineer, we write you becasuse we need a schematic diagram of one of your DC drives in order to retrofit a Bridgeport Mill Machine with Anilam Crusader II panel. Any other information will be gladly recievedThe driver is: Westamp Inc, Assy 30059.We would be very p...
Show More
➡️ Reply
#Westamp by Harold Godwin on 2008-02-21 15:55
I have the same control and am in need of schematic for westamp drive so I can determine whether I have a drive problem or control problem
➡️ Reply
#Westamp - Ultradrive by Matt Saponara on 2008-06-13 13:59
We have an older Campbell CNC Router which has a westamp drive unit. Westamp Ser. # 756; Mod. # A7214-17F-003(041886). We cant get drive cards anymore and the repaired ones are not lasting. Can we upgrade to a newer drive unit?Matt SaponaraMaintenance ManagerHunter Marine386-462-3658
➡️ Reply
#Westamp by quocphan on 2008-10-08 14:10
order chip TOSHIBA TF1204 QTY:40
➡️ Reply
#Westamp by miguel rangel on 2009-04-30 01:53
I have a milling machine, eqquiped with servocontrol, it has two cards with label WESTAMP 30059-.one of them have some burned components (diodes, resistors)I don`t have any information of the circuit cards.can you help me to obtain schematics or send me information about repair service?thanks
➡️ Reply
#Westamp by GARY LEBLANC on 2009-11-02 17:44
Hello,I am looking for the following circuit/test board:Westamp Inc. Assy 34235 Circuit/Test Board or Assy 34233 Rev. AThank you
➡️ Reply
#Westamp by RITA-DU on 2010-10-20 06:05
30060-116servometer drive board£¬made by Westamp £¬ 1PCSused for NV10-160
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.