K.E.W for Service call 1-336-969-0110 at Industrial Electronics Repair

K.E.W Service & Repair Forum

All the lights on the temp gauge lit means that the fuel tankis empty. If there is fuel in the tank, there may not be enoughto activate the tank sensor. put more fuel in.If the tank is full,the tank sender is faulty. It will need replacing.In the meentime you can bypass the tank sender by shorting out the two wires. Follow the cable up from the diesel tank up to the circuitboard inside the electrics box.cut the two wires that go to the circuit board and strip of insulation. Twist these wires togetherand this should solve the problem. If not, Either the board isknackered or the temperature sensor is knakered. The temperature sensor is located underneath the boiler on the water outlet andshould have a red wire coming of it up to the circuit board.Remove these 2 wires from the curcuit board and measure theresistance between these wires.It should measure around 500 ohmsat room temperatre. If not it requires replacing.You can Temporaryiliybypass the temperature sensor by repacing it with a 500 ohms resistor,any problems or if you need any parts email me regards.

— Posted by lyndon hammill on 2006-11-06

Reply🗨️Ask a New Question Below❓

If you need your K.E.W unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 95 Comments

#K.E.W by Josh Campbell on 2005-10-26 14:14

I am trying to refurbish a kew 1502v-66 power washer. I cannot get the oil fired burner to kick on. The control panel has a digital temp gauge and it shows the temperature of the water at its maximum value when the water is cold. I am in question if this is the problem with the burner not firing. I ...
Show More

#K.E.W by lyndon hammill on 2006-11-06 19:24

All the lights on the temp gauge lit means that the fuel tankis empty. If there is fuel in the tank, there may not be enoughto activate the tank sensor. put more fuel in.If the tank is full,the tank sender is faulty. It will need replacing.In the meentime you can bypass the tank sender by shorting o...
Show More

#K.E.W by Kevin Gonneau on 2007-05-07 19:40

Looking for parts manual of help with parts for Unit Model #3803V-103 1985/40No.# 2104067 240v/1/30 ampAny help would be greatly appreciated.

#K.E.W by dan johnson on 2007-05-28 23:54

I am trying to find out any info on this Kew (0802v-56)steam washer. If someone has a manual available, that would be great.

#K.E.W by Blair on 2007-08-15 01:10

call windy city equipment located in Elgin, Illinois

#K.E.W by Gerald Mansfield on 2007-10-01 00:46

I purchased a K.E.W. 1500 unit on a sale and would like to get an owners manual/service manual for it. It\'s an electric unit. Thank you, Gerry Mansfield

#K.E.W by Raymond Cooper on 2007-12-19 04:18

I need a service manual for a KEW 4503KB with exploded views, parts lists with prices... thank you for your time and help with this problem..Raymond Cooper951-926-5394

#K.E.W by KEIRON on 2008-04-03 18:18

my steam cleaner is flashing F1 light, does anyone know what this fault is and does anyone have a manuel for this model?many thanks

#K.E.W by ken Tucker on 2008-05-01 16:53

My KEW 1502v-66 is smoking badly and does not get hot. I think the diesel is not burning right. There is a blue flame between the contacts.

#K.E.W by gary appleton on 2008-06-10 15:53

i need new hose

#K.E.W by Joe Duran on 2008-06-13 23:41

Can I find a manual ?I was given one of these to me by a customer. I think I need a special water hose??

#K.E.W by mark on 2008-07-06 07:56

clean out the disel jet, clean out fillter under the fan, make sure u have good tight flexi hose connection, good luck

#K.E.W by swordcrown sevices on 2008-08-02 22:17

we have a KEW steam cleaner,not sure of age,trolley mounted, recent purchase, but not working.is there anybody out there who can help us, with regards to diagrams, or any possible imformation, perhaps we can then decide on further age, model etc , your help would be greatly appreciated.Yours sincere...
Show More

#K.E.W by Stuart on 2008-08-09 08:20

I need a service manual for a KEW 1502-66 with exploded views, parts lists with prices... thank you for your time and help with this problem..

#K.E.W by Six B Construction on 2008-10-02 15:28

I need a operation manuel for K.E.W. 3803V-103

#K.E.W by REYGAN on 2008-11-06 11:58

my steam cleaner 1640h is showing alarm F1 could anybody help me to find out the reason or send me manual of this machine thanksreygan bernard

#K.E.W by Arvid Hartsuiker on 2008-11-11 18:15

Front seal on pump leaking, looking for parts to repair and repair manual. Please give me a call or email. Thanks Arvid

#K.E.W by PAUL GALLAGHER on 2008-11-17 21:50

HI,I HAVE JUST PURCHASED A KEW 38A2VA POWER WASHER. IS IT POSSIBLE TO GET A MANUAL FOR THIS MACHINE? ALSO WHAT GOES IN THE TANK MARKED WITH A SNOWFLAKE?THANKS PAUL.

#K.E.W by Richard Lane on 2008-12-24 11:32

HelloI have a kew 1502 steam cleaner which has a problem with the burner. It will run for about 5 seconds then cut out, I have changed the diesel filter and cleaned the filter into the nozzle. Also I have checked that the electrodes are working properly. Its as if something is turning the diesel sup...
Show More

#K.E.W by William Knee on 2009-03-21 12:25

HI I check all and no start and I am a Electrician

#K.E.W by larry on 2009-03-26 07:25

need to find out how to change the unit from 110 volts to 220 volts. thanks

#K.E.W by Dale on 2009-04-08 00:10

Hi, put a oring kit in pump an still get only tap pressure everything looks good ,keyway on pump motor fine. any ideas. Thanks,

#K.E.W by Garry S James on 2009-04-09 10:26

I have a KEW 1502V – Hot & Cold Pressure Washer. I will be running this of a Generator at the same time as a water pump which has a rating of 700w.1. Can you what is the start up current of the Pressure Washer.2. What size Generator should I be looking for to run the Pressure Water and the Water...
Show More

#K.E.W by thomas thorn on 2009-05-03 09:24

The temprature regulator on the top of the washer is broken off next to the gauge i need a new part

#K.E.W by hans on 2009-05-13 16:54

i can\'t get pressure on my kew 1640H. But i have seen that there are watercristals in the pressuremeter. Does someone know what the problem is?Thanks

#K.E.W by Richard Beck on 2009-05-25 21:04

Have a Kew 3803V pressure washer, need to know where I can get itrepaired nearby.thank you

#K.E.W by cindy janeski on 2009-05-28 18:35

I am looking for a shop that carries replacement parts for a KEW pressure washer, the hose has sprung a leak and need to replace it the spray nozzle is also attached to the hose as a all in one unit

#K.E.W by ali on 2009-05-31 05:45

I\'m looking for the maintenance manual for this machine

#K.E.W by Gary on 2009-06-07 19:47

The burner won\'t turn off can anyone help

#K.E.W by David Kerr on 2009-06-12 19:28

Hi, Help please, i\'m in need of a new lance for my older Kew Hobby 2600, would you have this item in stock ?

#K.E.W by Martin Ferguson on 2009-07-10 14:10

No comments

#K.E.W by Chris bolton on 2009-07-10 15:22

My Kew is not building up pressure can you tell me why please

#K.E.W by thijs thissen on 2009-07-13 08:11

We have recently purchased an second hand KEW high pressure cleaner but it does not get the full cleaning pressure. Can I recieve an owners manual by email to see what parts may be broekn in order to fix the machine?Thank you in advance.best regards,Thijs.

#K.E.W by sandy stevens on 2009-09-28 13:03

Is there anyway to get a takedown of the pump on my kew steam cleaner the model # 08022-56? A parts book would be good.

#K.E.W by Tim on 2009-09-28 17:42

I am looking for a seal kit for the pump on this unit if you can get one please email me back.

#K.E.W by brian breslin on 2009-10-14 19:43

where might I download a user manual for parts and maintenance of my 1640h Thanks Brian

#K.E.W by Len on 2009-10-23 14:28

I have a copy of the users instruction book for this machine if you are still in need.

#K.E.W by Rudy Martens on 2009-10-28 06:19

I need a operation manual for KEW 1502v-66

#K.E.W by Ola Wikstrand on 2009-11-01 17:38

HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks! Ola

#K.E.W by Jeff Osborn on 2009-11-23 21:46

I have recently acquired a K.E.W. Pressure washer and am trying to find information about it. It appears to be from Denmark and in the Model box it just says Hobby. Another box on the ID plate says 62 bar. The gauge on the machine reads 0 to 150 and on the face of the dial it says X 1000. THAT WOULD...
Show More

#K.E.W by Tom Hamilton on 2009-12-16 22:16

I may have the same pressure washer you have. My pressure gauge shows two circular pressure scales. The outer scale is from 0 to 150 with a heavy mark at the 50 digit and 100 digit. At the bottom it says \"BAR\". If your information plate says 62 BAR as mine does then acceptable pressure i...
Show More

#K.E.W by MARK on 2010-01-02 19:00

My kew steam cleaner does not have water pressure. It exits the gun but only trickles out. Can you help? Many thanksMark

#K.E.W by SHABAN LIMANI on 2010-03-01 19:16

guten abent icsh bin ljimani cshaban aus macedonia tetovo icsh brauche eine pumpe for choch druck for kew 1502und kene cshiken in macedonia und kenen preis ceigen bite und in duetsh ich veis bite und in meine email cshriben bite filen dank fur das

#K.E.W by jonas hofer on 2010-03-14 22:44

I need an instruction manual for a KEW 1640H When i put power to it, it just shut\'s off after two seconds, and i have to reset it. A sign in the small screen say\'s, P1 and F1 i don\'t know what they mean.

#K.E.W by Ruth Montefiore on 2010-03-15 13:33

The black hose pipe connected to this pressure washer has a whole in it. Can it be repaired and if so how please. If not how much will it cost to desptach a replacement to me or where can I purchase this hose pipe? Is it something I can obtain from a builders merchants and if so what size please?I l...
Show More

#K.E.W by marcondes on 2010-03-17 22:11

my machine stop work hot water and pressure no good work

#K.E.W by maria helena on 2010-03-17 22:12

i need manual for kew 1640ha

#K.E.W by AUSTIN GIBBONS on 2010-03-30 14:40

CAN I BUY A SPARE PART FOR THE ABOVE, IE, THE PRESSURE WASHER AT THE END OF THE LANCE.?WITH THANKS AUSTIN GIBBONS

#K.E.W by reidar kvalvik on 2010-04-19 13:53

Hi.I need reper manual for KEW royalBest regards Reidar Kvalvik

#K.E.W by LIMANI on 2010-08-08 21:44

guten abent icsh bin limani cshaban aus macedonia icsh brauche eine tail for meine macshine das chaist pumpe for k.e.w.1502 iat mit drei klipen un federen und kenzi zaigen prais bite

#K.E.W by Odyssey Winery on 2010-08-23 21:14

I have a KEW pressure washer, model 0840HA. I am receiving intermittant F2 error codes and C4 error codes. I have taken it into my dealer for \"repair\" however the problem continues. Any ideas?

#K.E.W by gary case on 2010-09-23 15:00

we can\'t get water flow through the machine

#K.E.W by Hassan Mortazavi on 2010-10-08 16:23

i just got a used ke w scorpian steam cleaner and everything works exept it does not ignite or no spark to get flame.any idea.thankshassan

#K.E.W by Murray Smith on 2010-10-09 06:33

I need a instruction manual for a KEW 1502-66 thank you

#K.E.W by Hassan. Mortazavi on 2010-10-10 01:05

How do i test the electrod or egniter to see its good?Thanks

#K.E.W by Clifford Brown on 2010-10-10 03:46

I still do not have all the details of what this machine is, but it appears to be a hot water pressure washer.. Would be interested in the instructions manual to see if I can get it going. Do not have all of the ID place numbers copied down yet though. The copper windings for the boiler look good fr...
Show More

#K.E.W by Ron on 2010-10-12 02:52

My coil froze last winer when heater broke in shop over weekend , do you have any coils

#K.E.W by frank welch on 2010-12-02 13:46

just want to know how old this machine is and if it can still be repaired,i have no knowledge of what year it was made and know of no place to get it repaired

#K.E.W by m j cars on 2011-03-17 11:08

when i turn the machine on it trips the electrick

#K.E.W by ryan on 2011-04-02 17:51

I have a 1979 kew power washer and am looking for some pump parts or info on where to get parts it is mostly all in good shape put the pump needs work any info would be greatly apresated thanks ryan

#K.E.W by J.den Dekker on 2011-04-03 06:34

Geachte meneer/mevrouw,Ik heb heb kew 1500 hogedruk spuitpart nr. 6137219 Serial nr. 6998760.Kunt u mij vertellen of ik een terrascleaner kan krijgen voor deze hogedruk spuit en als dat mogelijk is kunt u mij vertellen waar en wat hij kost.vr.gr.J.den Dekker

#K.E.W by CESAR ALCAZAR on 2011-04-18 14:09

Hi I have a Heated Pressure Washer, and Im lookin for a specific part can you tell me if ispossible to found it. Lelow information of the machineMAKER: KEWMODELL: 3803V-103SER:2103205ASSET:43-1-5

#K.E.W by Adrian Frost on 2011-05-16 11:17

Hi, I have a KEW Steam Cleaner model 16A2V-66 Year 1986. I bought it from a company asset auction and never saw it working. I have now tried to use it and the temperature lights reached the temperature set once, then the burner went out and would not re-light. I dissconnected the fuel supply to the ...
Show More

#K.E.W by steve oiveros on 2011-06-20 23:33

I need a parts schematic so I could repair the pump I need the seals kit.

#K.E.W by Carolyn S. Valdivia on 2011-06-22 21:16

KEW 3803V-103 fuel pump is not delivering to the burner. Please either send a manual or advise. I will call for technical assistance 6/23/2011Thank you Carolyn S. ValdiviaJackson Drop Storage YardTruck & Trailer Repair517-795-1353

#K.E.W by steve oliveros on 2011-06-24 22:12

i need a parts list so i could repair the pump

#K.E.W by shaban limani on 2011-07-02 17:12

JA ICSH BIN LIMANI CSHABAN ICSH BRAUCHE EINE PUMP MACSHINE FOR AUTO VACSH MACSHINE IST FOR MARKE K.E.W 1502V ICSH CHAP MACSHINE ABER PUMP IST KAPUT BITEIN MAINE EMAIL CSHIKENSI DI VORT FOR MAINE RESPEKT

#K.E.W by Bob Schultz III on 2011-08-17 15:47

I need a service manual with part numbers and specifacation please.

#K.E.W by Hartono on 2011-10-19 06:46

Dear AllPlease give me the information about Services center KEW 0901V In indonesia , for your best cooperation i would to say many thanks

#K.E.W by john farkas on 2011-10-26 18:38

I am looking a the circuit board for my 0840HA hot water pressure washer. Mine burned out, the rest of the machine is nearly new. It would be a shame to trash it. KEW no longer makes this board.

#K.E.W by john farkas on 2011-10-26 18:47

For any KEW products call Chris Gerber in S.C. (877)322-2586. Very knowledgable and helpfull. He is the US service rep.

#K.E.W by ken williams on 2011-11-08 03:02

Hi would you have a service manual for this cleaner??

#K.E.W by Amin on 2011-12-28 06:46

I have Kew 1640h i need operating manual,

#K.E.W by Grant Neeley on 2012-01-24 13:44

I have a KEW 23A2V pressure washer that the boiler Coil is completely shot now. I have welded some hole back together, but now it is beyond repair. Does anyone know where I can get a replacement coil?

#K.E.W by holmeside garage lee scott on 2012-02-13 22:01

i have a kew 1640ha which i am having a bit trouble with reacently when whent to use it it cum up with the fault L1 and now the machine will not start,i was wundering if you could give me a bit help THANKS

#K.E.W by Owen Torgerson on 2012-03-22 19:12

Great machine, had since new, recently experiencing difficulties acquiring heat.Lots of kerosene, lots of pressure on cold, new fuel spray nozzle...Help

#K.E.W by Anthony blair rowland on 2012-06-04 19:58

Please can you help i have a kew 1502v it will run fine cold, as soon as i demand heat it runs for 5 seconds and switches off if you switch it on & off,it runs for 5seconds and it will do this all day. what is the solution please

#K.E.W by Antonio Gonzalez on 2012-06-19 13:41

need the service manual of KEW 01K pressure washer

#K.E.W by Scott A Wilson I on 2012-07-24 12:43

Hi there.I have A Kew steam cleaner model #0802v-56 And would like to see about getting these manual\'s for this cleaner . Please and thank you . Scott

#K.E.W by Brent C. on 2012-10-02 22:26

No fuel getting to burner, need manual for test procedure. Thank you, Brent C.

#K.E.W by leo on 2012-10-14 09:11

DO YOU HAVE A SOLUTION FOR THE OIL VALVE FROM THE BURNERIT WILL NOT GO ON BY WORKING WITH THE MACHINEPRESSION KONTAKTS ARE OKE

#K.E.W by mario yasin on 2012-12-04 21:44

i need to fix my pei kew 4503kb pumbe kit and throtecan you fix itthank you

#K.E.W by dan lucas on 2013-03-13 22:08

hi i brought this k.e.w h1500 steam cleaner some year ago,i put it away after it was working ok over 12month ago.i lent it to my brother and it will not pressure up.....his any one out there i can ring to get parts so i can fix it thx 07779666678

#K.E.W by Serge on 2013-06-13 13:06

HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks!

#K.E.W by TOBY ANDERSON on 2014-08-15 17:47

I have a kew alto 2340ha Everything was working and the usint up and quit It showed a 0 flashing and I unplougged it and put it back it reset to solid 0 but when you push the power on it does nothing. I let sit unplugged but nothing works now. Is there anyone who works on these anymore I am in Wisco...
Show More

#K.E.W by mark on 2014-10-21 13:50

hi could you tell me where I would get service manual for kew 1640hathanks mark

#K.E.W by Ulf Dahl on 2015-03-24 13:14

HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks!Uffe

#K.E.W by EdwardKn on 2015-03-27 17:20

Hello. And Bye.

#K.E.W by mohammed zaki on 2015-03-30 11:01

HelloPlease can you inform me where i can repair my washing machinemodel (5203k) in united arab emitares.Thanks @ Best Regards

#K.E.W by JAMES FARMER on 2016-05-02 19:22

the fuel will not pump, I don`t have the voltage coming out of the oil area of the board to open the solenoid on the fuel pump. I need a schematic to trace the problem, is there one available ?

#K.E.W by Tom Duclos on 2016-05-31 14:22

Need transformer for above unit part number #3819901 can you help me..

#K.E.W by Bodengien on 2017-12-18 08:27

HelloBought a secand hand KEW38A2VA and overhauld and cleanend the machine. The boiler doesnt start however. Can I get a manual for the machine ?? Thanks in advance. Bodengien.

#K.E.W by angelineadlecraft@gmail.com on 2019-05-02 14:02

Good dayI am trying to find a manual to assist me with the heating system of a K.E.W. 38A2VA.Many thanks

#K.E.W by Jesus on 2019-10-11 08:59

Hi I have a KEW 1502v and some body stolen parts so I put all back together but for any reason it not working the heater and I suspected it about the wiring position, and the pressure is stopping and not keep spraying and some times work fine but some times not, one time I fix only with a new clamp ...
Show More

#K.E.W by Bože Gudelj on 2021-01-28 20:56

KEW 1502 V-66 user manual , service manual

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.