Accu-Rite Service & Repair Forum

I have an Acu-rite DRO, 2xmill9200, part number 2001003, SN 98042347 Rev B. When I push the 1 or 2 button on the key pad. nothing happens. Is this repairable? if so, what would be the estimated cost to do this? ThanksRob

— Posted by Robbie Regennitter on 2012-12-09

Reply🗨️Ask a New Question Below❓

If you need your Accu-Rite unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 9 Comments

#Accu-Rite by Bruce Thomas on 2006-08-25 20:53
I would like to know if you sell new or used accurite III dro\'s?Mine is a lost cause. It was being used in the z axis and in congunction with Servo system 3 axis milling machine retro-fit, on a Lagun ftv-2 base machine. the 2 other axis dro\'s are fine.. Bruce
➡️ Reply
#Accu-Rite by peter on 2008-07-05 14:15
where can i find a on line or other instruction manual for this Digital Read out?
➡️ Reply
#Accu-Rite by Craig Lindberg on 2009-01-09 16:17
To whom it may concern,I have an Accu Rite II Digital Readout System on my Bridgeport.The (X) axis reading head, is in need of a rebuild. Is this something your company does or can you refer me to someone?Any info. on this would be greatly appreciated. Thanks for your time,Craig
➡️ Reply
#Accu-Rite by Dennis Van Niel on 2009-08-25 13:35
I need to find or have ours repaired. It is a 10\" scale for a hardinge lathe model 200T. The scale number is 550505-10
➡️ Reply
#Accu-Rite by Tom Kish on 2009-10-09 16:18
My read out keeps giving me an e3 code . The readout starts reading out then goes to e3.The scale is clean also the readerhead had everything apart cleaned with alcohol . Can you help? The mode is a Millmate 2 axis it is on a Brigeport mill. Tom
➡️ Reply
#Accu-Rite by Eric Allen on 2010-10-01 16:12
Hello, I have a Accu-rite III dro, and just in stalled a new Y-axis scale.How do you change the resolution on the DRO?
➡️ Reply
#Accu-Rite by m.s.bisht on 2011-01-16 09:41
we wants setting least count 5 micron instead of 10 micron. please send me detail
➡️ Reply
#Accu-Rite by Robbie Regennitter on 2012-12-09 22:26
I have an Acu-rite DRO, 2xmill9200, part number 2001003, SN 98042347 Rev B. When I push the 1 or 2 button on the key pad. nothing happens. Is this repairable? if so, what would be the estimated cost to do this? ThanksRob
➡️ Reply
#Accu-Rite by Carl Vandewinckel on 2022-04-06 20:08
I have two Teledyne DRO Model 2000.Do you of anyone that can fix them? We can discuss the issue on the phone.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.