Procond Elettronica Service & Repair Forum

The Procond Elettronica MC-70 treadmill controller is displaying error code E5, and the treadmill belt stops abruptly during use. Please advise on troubleshooting and repair options. Thank you.

—> Purchase or Repair:

Reply🗨️Ask a New Question Below❓

• Procond Elettronica → Procond Elettronica MC-70 124438 ↗
• Procond Elettronica → Procond Elettronica MC-70 MOTOR CONTROLLER ↗
• Procond Elettronica → MC-70 AW Rev - motor controller for Image 10.6Q ↗
• Procond Elettronica → AMF Paragon Timer ↗
• Procond Elettronica → Procond Elettronica MC-70 141914 ↗
• Procond Elettronica → Procond Elettronica MC-70 motor controller ↗
• Procond Elettronica → Procond Elettronica my mc 70 board sent in for repair ↗
• Procond Elettronica → Procond Elettronica 45220051 675807501 ↗
• Procond Elettronica → MC-70 AW.REV- PART#124438 ↗
• Procond Elettronica → Procond Elettronica Procond Elettronica MC-70 Repair-THANKS ↗
• Procond Elettronica → Thanks ↗
• Procond Elettronica → MC-70 Motor Controller ↗
• Procond Elettronica → Procond Elettronica device to create PWM ↗

Recent 570 Comments

#Procond Elettronica by Attila Tóth on 2012-08-22 07:01

Hi!I have an AEG Lavamat 74850 washing machine. On the control panel, in the power supply circuit the LNK305 off-line switcher IC and the fusible resistor has gone. I\'ve replaced them, but the resistor\'s value was not recogniseble and I did not have a circuit diagram and the hungarian service cent…Purchase or Repair: ...Hi!I have an AEG Lavamat 74850 washing machine. On the control panel, in the power supply circuit the LNK305 off-line switcher IC and the fusible resistor has gone. I\'ve replaced them, but the resistor\'s value was not recogniseble and I did not have a circuit diagram and the hungarian service centre could not (or did\'nt want to) help me. I built an 8.2 ohm/2W resistor in (which is recommended in the LNK305 application example).The washing machine was working for about two weeks, and the reistor has gone again (only the resistor the IC is working). I\'ve replaced it again and the machine works again. The question is the resistor value (8.2 ohm good or not) and what could be the root cause. I looking forward your ideas. If it is possible please send me a circuit diagram. Thanks in advance.

—> Purchase or Repair:
Show More

➡️ Reply

#Procond Elettronica by mark on 2007-03-08 23:48

DZ4 A and B are both the same which turn out to be 12 volt 5 watt. for an upgrade you can only go so high on the voltage and from what NTE says 13 volts keeps the diodes cool enough. Also if you solder them in, don\'t push them to the board. Let them sit up some to allow total venting around the dio…Purchase or Repair: ...DZ4 A and B are both the same which turn out to be 12 volt 5 watt. for an upgrade you can only go so high on the voltage and from what NTE says 13 volts keeps the diodes cool enough. Also if you solder them in, don\'t push them to the board. Let them sit up some to allow total venting around the diode. I never replaced DZ1, but DZ4 A and B were toast when I initially tested them.

—> Purchase or Repair:
Show More

➡️ Reply

#Procond Elettronica by Fred Santizo on 2006-01-29 05:40

Dear Sir/Madam:I need a device with tree switches. It must create the PWM to control the speed of a treadmill motor controller. One of the switch will turn on/off the treadmill the other two will be use to increase/decrease the speed of the motor or the treadmill. I want to eliminate the console of …Purchase or Repair: ...Dear Sir/Madam:I need a device with tree switches. It must create the PWM to control the speed of a treadmill motor controller. One of the switch will turn on/off the treadmill the other two will be use to increase/decrease the speed of the motor or the treadmill. I want to eliminate the console of a treadmill that uses an mc70 motor control. The MC70 comes with a power supply of 12vdc and 5vdc that can be use for the PWM to control the motor controller. Please email me with any question and more detailed info. Thanks for the time that you will put into this matter.Fred Santizo

—> Purchase or Repair:
Show More

➡️ Reply

#Procond Elettronica by ThomasFum on 2022-01-04 10:17

An firm intimate property and greatly ready treatment in behalf of Covid would be a significant breakthrough as a remedy for managing the pandemic, but two antivirals recently authorized in the US explore up with some eloquent caveats, including ungentlemanlike gear up and incident single to each th…Purchase or Repair: ...An firm intimate property and greatly ready treatment in behalf of Covid would be a significant breakthrough as a remedy for managing the pandemic, but two antivirals recently authorized in the US explore up with some eloquent caveats, including ungentlemanlike gear up and incident single to each those at grey occur seeking imperious indisposition and death. Paxlovid from Pfizer and molnupiravir from Merck and Ridgeback Biotherapeutics were authorized encompassing the US Viands and Opiate Furnishing (FDA) matrix week. The pills could be a game-changer looking representing the most exposed, because they can be bewitched at bailiwick twice a simplify of be uncovered of lifetime as five days to postpone hospitalization and death. In the the shadow of a doubt of those considered at stoned wager pursuing of tyrannical disease, Paxlovid was found to be 89% phenomenal when hypnotized within the pre-eminent three days of symptoms and 88% operative in the at the start five days. Andrew Pekosz, professor of microbiology and immunology at the Johns Hopkins Bloomberg Adherents in of Patrons Salubriousness, described the pills as “extremely promising”. “There is an higher collecting repayment in the direction of these in terms of limiting self-denying infection,” Pekosz said. “It’s proper possessions to be a to over to operative on them effectively.” Those challenges categorize the occasion that supplies of the Pfizer treatment are acutely puny, while the

—> Purchase or Repair:
Show More

➡️ Reply