Tajima Service & Repair Forum

The drive board on your Tajima CX5609030000 is malfunctioning, causing the unit to display errors or be unresponsive during operation. To solve this issue, it is recommended to replace the drive board components. The estimated cost for this repair depends on the extent of the damage and the overall value of the unit.

— Posted by Rod Chandler on 2013-07-13

Reply🗨️Ask a New Question Below❓

If you need your Tajima unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 9 Comments

#Tajima by Noel Declaro on 2006-03-11 08:42
I would like to know if you can repair the above mention PCB? How long it take to repair and how much it will cost?
➡️ Reply
#Tajima by CARLOS MARTINEZ on 2007-02-12 16:40
I HAVE A TMEF-H612 EMBROIDERY MACHINE THAT ITS X/Y CONTROLLER IS DAMAGED AND I WANT TO KNOW IF YOU CAN REPAIR THIS BOARD AND HOW MUCH IT WILL COST.
➡️ Reply
#Tajima by surbhi jain on 2007-10-10 11:34
DEAR SIR I WANT TO BUY DU10 XY CARD, WORKING CONDITION,PLEASE TELL ME THE PRICE AND ALSO THE COURIER CHARGES.THANKS.SURBHI,.
➡️ Reply
#Tajima by warner gonzalez on 2008-02-08 01:39
I have an embroidery machine tajima temg-g618 but it is does not work only can see in the screen the next code :3d7main shaft motor speed control have some problem .or cpu board is bad .Can you help me?Thank you so muchwarner
➡️ Reply
#Tajima by m.abbas on 2008-09-21 17:03
we want a new tajima du-10driver box its ser-EH5404090000
➡️ Reply
#Tajima by Lynn Waterhouse on 2010-01-19 18:50
What would you charge for a \"house call\" to Mebane, NC to take a look at my Tajima single head embroidery machine? Please email your reply...Thanks,Lynn
➡️ Reply
#Tajima by javier acosta on 2011-11-14 15:52
good morning.I need urg board electronic for tajima.refe ED5101030000.new or used perfect .thanks a lot..or do you have electronic partsjavier
➡️ Reply
#Tajima by Rod Chandler on 2013-07-13 23:49
The drive board on your Tajima CX5609030000 is malfunctioning, causing the unit to display errors or be unresponsive during operation. To solve this issue, it is recommended to replace the drive board components. The estimated cost for this repair depends on the extent of the damage and the overall ...
Show More
➡️ Reply
#Tajima by FERNANDO RODRIGUEZ on 2019-11-26 00:39
I need to repair two DU-10 boards of our embroidery. Model TMFD-G920. What will be an estimated cost. Where I can send you the boards? and what would be the estimated repair time?
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.