Hartmann & Lammle Hartman & Lammie Controller 781 462-602   Posted by Gordon McFadin on Tuesday, December 7 2010 We have two Trumpf 500 punches (circa 1997) that both use the H&L controller 781 462-602. A problem developed in one that caused an initiation failure at power-up when the punch calibrated the tool height. we swapped controllers and the problem followed the original controller (although occasionally both punches would work for a short time after swapping but would eventually fail in the same way). Having isolated the problem to a particular controller I decided to swap elements of the faulty one to the good one, hoping to identify what is actually failing. My troubleshooting finally led to the backplane where the cards are seated as being the problem. I could swap it between machines and the problem would follow the backplane. My question is that there are very few active components on the board and I have swapped all but the three filter caps across the power supply (they measure good). Have you run into this as a problem before and what might it be and can you repair this or sell us a replacement backplane? Thanks for your help in this. I am pretty much at the end of my troubleshooting rope at this point. Gordon McFadin Intrapack Corp.   Current thread: Copy serve-valve Return Home to Hartmann & Lammle Need to get your Hartmann & Lammle Repaired? Quickly Hire our Service Dept to do the work for you! Credit Application Form Free Estimate Contact Sales 1-336-969-0110 If you need your Hartmann & Lammle unit tested or repaired then give us a call at 1-336-969-0110. We give free estimates and offer a year warranty. Shipping info Industrial Electronic Repair 266 Northstar Dr. Suite 136 Rural Hall, NC 27045 fax: 1-(336)-969-0101

• Need a Hass processor board repaired  Dan Monday, January 15 2018 12:50 pm
  
• BOARD REPAIR, #041650 IN MY MACHINE  GARY Friday, February 17 2017 3:42 pm
  
• RFQ for CANLINK I/O Module ( CL-411-102)  Mr.Lin Tuesday, July 26 2016 7:34 am
  
• Hol-Gar Hol Gar 3 phase 120/240 gas/propane  Otis Wednesday, April 17 2013 12:32 am
  
• Hol-Gar Hol Gar 3 phase 120/240 gas/propane  Otis Wednesday, April 17 2013 12:31 am
  
• Horyu Engineering Horyu MSE-30B-2U-HS  Tonolli Friday, February 15 2013 10:53 am
  
• Hol-Gar Electric Starter for Hol-Gar Generator  Alvin Sunday, October 30 2011 1:15 am
  
• Hydrolux hydrolux ultra flow macerator  robin Monday, October 24 2011 7:25 pm
  
• Hofliger & Karg Instruction Manual Hofliger&Karg gkf150st  Thanos Friday, September 30 2011 9:34 am
  
• Hipot Repair Hipot  usCalibration Tuesday, February 15 2011 6:53 pm
  
• Hartmann & Lammle Hartman & Lammie Controller 781 462-602  Gordon Tuesday, December 7 2010 7:22 pm
  
• Heldt & Rossi Servo  Frank Tuesday, April 20 2010 6:18 pm
  
• Hol-Gar Hol-Gar cs-107-ac  Dan Monday, March 8 2010 2:56 am
  
• Hofa Engineering inverter  spinu Friday, February 12 2010 7:53 pm
  
• Hofliger & Karg Encapsulator Info  Mark Tuesday, November 17 2009 8:04 pm
  
• H & S 4-Imidazolecarboxaldehyde  4-Imidazolecarboxaldehyde Wednesday, March 12 2008 1:47 pm
  
• Hays Republic Hydraulic Positioner  jorge Tuesday, August 14 2007 12:42 pm
  
• Horyu Engineering Horyu Engineering Horyo Spindle drive  Baduwasam Thursday, April 20 2006 6:16 am
  
• Hyster Grid Packer SN:A53116143  Dale Monday, March 27 2006 2:54 pm
  
• Heimann Heimann Harness Tester for Gravure Cylinder  Aurelio Monday, March 20 2006 3:30 am
  
• Hofliger & Karg gkf50 instruction manual  Sheldon Wednesday, February 22 2006 4:49 am
  
• Heenan Drives Ltd. Repair of Defective Heenan Drive  Abdulla Wednesday, January 18 2006 7:45 am
  
• Hydrocraft Pistion Pump Type PV250/DR  Omar Monday, December 19 2005 5:20 pm
  
• Heenan Drives Ltd. Technical Information of Heenan 200/6 Excitation u  Tony Tuesday, December 13 2005 7:40 am
  
• Horyu Engineering Horyo Spindle drive  Malcolm Tuesday, November 22 2005 9:49 am
  
• Hantarex 21" Vicon module VM621-P  kahchoong Wednesday, July 27 2005 3:23 am
  
• HBO Instruments Temperature Controller  Stan Tuesday, May 24 2005 7:12 pm