K.E.W for Service call 1-336-969-0110 at Industrial Electronics Repair

K.E.W Service & Repair Forum

All the lights on the temp gauge lit means that the fuel tankis empty. If there is fuel in the tank, there may not be enoughto activate the tank sensor. put more fuel in.If the tank is full,the tank sender is faulty. It will need replacing.In the meentime you can bypass the tank sender by shorting out the two wires. Follow the cable up from the diesel tank up to the circuitboard inside the electrics box.cut the two wires that go to the circuit board and strip of insulation. Twist these wires togetherand this should solve the problem. If not, Either the board isknackered or the temperature sensor is knakered. The temperature sensor is located underneath the boiler on the water outlet andshould have a red wire coming of it up to the circuit board.Remove these 2 wires from the curcuit board and measure theresistance between these wires.It should measure around 500 ohmsat room temperatre. If not it requires replacing.You can Temporaryiliybypass the temperature sensor by repacing it with a 500 ohms resistor,any problems or if you need any parts email me regards.

— Posted by lyndon hammill on 2006-11-06

Reply🗨️Ask a New Question Below❓

Recent Comments Search: "K.E.W"

K.E.W → K.E.W. : OWNERS MANUAL ↗
K.E.W → KEW 1502v-66 ↗
K.E.W → K.E.W. K.E.W. 1500 Power Washer ↗
K.E.W → K.E.W. : kew pressure washer o8o2v-56 ↗
K.E.W → K.E.W. Repair ↗
K.E.W → K.E.W. Kew 1502v-66 ↗
K.E.W → K.E.W. : maintenance manual ↗
K.E.W → no pressure ↗
K.E.W → K.E.W. ↗
K.E.W → KEW 4503kb ↗
K.E.W → KEW pressure washer ↗
K.E.W → Kew 1502 ↗
K.E.W → K.E.W. : Kew 1502v ↗
K.E.W → kew1640ha ↗
K.E.W → K.E.W. where to get manual for a 1640h ↗
K.E.W → Kew 1502v-66 pressure washer ↗
K.E.W → K.E.W. : KEW STEAM CLEANER ↗
K.E.W → service manual ↗
K.E.W → KEW HOBBY 100-1 ↗
K.E.W → kew 1640H ↗
K.E.W → K.E.W. KEW 1502v ↗
K.E.W → K.E.W. Hobby pressure washer ↗
K.E.W → KEW royal ↗
K.E.W → K.E.W. : KEW hot water power washer ↗
K.E.W → Manual for Kew 38A2VA thanks ↗
K.E.W → parts book pump ↗
K.E.W → tail for mashine ↗
K.E.W → K.E.W. KEW Model 3803V ↗
K.E.W → K.E.W. Kew 1502-66 ↗
K.E.W → K.E.W. : Kew1502v - 66 ↗
K.E.W → k.e.w. 1502v-66 tempreture regulator adj ↗
K.E.W → kew 1500 hobby ↗
K.E.W → K.E.W. : KEW Help ↗
K.E.W → K.E.W. : kew 0802v -56 ↗
K.E.W → parts for kew steam cleaner ↗
K.E.W → Kew 1502 manual ↗
K.E.W → K.E.W. KEW 38A2VA ↗
K.E.W → pressure ↗
K.E.W → Kew Hobby 1500 Pressure Washer ↗
K.E.W → K.E.W. KEW HOT WATER WASHER ↗
K.E.W → manual ↗
K.E.W → K.E.W. : kew 38A2VA ↗
K.E.W → K.E.W. : kew steam cleaner ↗
K.E.W → K.E.W. : Jonas ↗
K.E.W → K.E.W. : kew 1502 ↗
K.E.W → K.E.W. : kew 1640H ↗
K.E.W → par til for kew 1502 ↗
K.E.W → Kew Hobby 2600 ↗
K.E.W → operation manuel ↗

If you need your K.E.W unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 95 Comments

#K.E.W by Tom Hamilton on 2009-12-16 22:16

I may have the same pressure washer you have. My pressure gauge shows two circular pressure scales. The outer scale is from 0 to 150 with a heavy mark at the 50 digit and 100 digit. At the bottom it says \"BAR\". If your information plate says 62 BAR as mine does then acceptable pressure is between …...
Show More

#K.E.W by Martin Ferguson on 2009-07-10 14:10

No comments

#K.E.W by ken Tucker on 2008-05-01 16:53

My KEW 1502v-66 is smoking badly and does not get hot. I think the diesel is not burning right. There is a blue flame between the contacts.

#K.E.W by angelineadlecraft@gmail.com on 2019-05-02 14:02

Good dayI am trying to find a manual to assist me with the heating system of a K.E.W. 38A2VA.Many thanks

#K.E.W by Bože Gudelj on 2021-01-28 20:56

KEW 1502 V-66 user manual , service manual

#K.E.W by Grant Neeley on 2012-01-24 13:44

I have a KEW 23A2V pressure washer that the boiler Coil is completely shot now. I have welded some hole back together, but now it is beyond repair. Does anyone know where I can get a replacement coil?

#K.E.W by Ron on 2010-10-12 02:52

My coil froze last winer when heater broke in shop over weekend , do you have any coils

#K.E.W by thomas thorn on 2009-05-03 09:24

The temprature regulator on the top of the washer is broken off next to the gauge i need a new part

#K.E.W by Richard Lane on 2008-12-24 11:32

HelloI have a kew 1502 steam cleaner which has a problem with the burner. It will run for about 5 seconds then cut out, I have changed the diesel filter and cleaned the filter into the nozzle. Also I have checked that the electrodes are working properly. Its as if something is turning the diesel sup…...
Show More

#K.E.W by Ulf Dahl on 2015-03-24 13:14

HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks!Uffe

#K.E.W by frank welch on 2010-12-02 13:46

just want to know how old this machine is and if it can still be repaired,i have no knowledge of what year it was made and know of no place to get it repaired

#K.E.W by KEIRON on 2008-04-03 18:18

my steam cleaner is flashing F1 light, does anyone know what this fault is and does anyone have a manuel for this model?many thanks

#K.E.W by reidar kvalvik on 2010-04-19 13:53

Hi.I need reper manual for KEW royalBest regards Reidar Kvalvik

#K.E.W by maria helena on 2010-03-17 22:12

i need manual for kew 1640ha

#K.E.W by steve oliveros on 2011-06-24 22:12

i need a parts list so i could repair the pump

#K.E.W by holmeside garage lee scott on 2012-02-13 22:01

i have a kew 1640ha which i am having a bit trouble with reacently when whent to use it it cum up with the fault L1 and now the machine will not start,i was wundering if you could give me a bit help THANKS

#K.E.W by Arvid Hartsuiker on 2008-11-11 18:15

Front seal on pump leaking, looking for parts to repair and repair manual. Please give me a call or email. Thanks Arvid

#K.E.W by Stuart on 2008-08-09 08:20

I need a service manual for a KEW 1502-66 with exploded views, parts lists with prices... thank you for your time and help with this problem..

#K.E.W by Bodengien on 2017-12-18 08:27

HelloBought a secand hand KEW38A2VA and overhauld and cleanend the machine. The boiler doesnt start however. Can I get a manual for the machine ?? Thanks in advance. Bodengien.

#K.E.W by MARK on 2010-01-02 19:00

My kew steam cleaner does not have water pressure. It exits the gun but only trickles out. Can you help? Many thanksMark

#K.E.W by Joe Duran on 2008-06-13 23:41

Can I find a manual ?I was given one of these to me by a customer. I think I need a special water hose??

#K.E.W by LIMANI on 2010-08-08 21:44

guten abent icsh bin limani cshaban aus macedonia icsh brauche eine tail for meine macshine das chaist pumpe for k.e.w.1502 iat mit drei klipen un federen und kenzi zaigen prais bite

#K.E.W by john farkas on 2011-10-26 18:38

I am looking a the circuit board for my 0840HA hot water pressure washer. Mine burned out, the rest of the machine is nearly new. It would be a shame to trash it. KEW no longer makes this board.

#K.E.W by larry on 2009-03-26 07:25

need to find out how to change the unit from 110 volts to 220 volts. thanks

#K.E.W by Gary on 2009-06-07 19:47

The burner won\'t turn off can anyone help

#K.E.W by Jeff Osborn on 2009-11-23 21:46

I have recently acquired a K.E.W. Pressure washer and am trying to find information about it. It appears to be from Denmark and in the Model box it just says Hobby. Another box on the ID plate says 62 bar. The gauge on the machine reads 0 to 150 and on the face of the dial it says X 1000. THAT WOULD…...
Show More

#K.E.W by jonas hofer on 2010-03-14 22:44

I need an instruction manual for a KEW 1640H When i put power to it, it just shut\'s off after two seconds, and i have to reset it. A sign in the small screen say\'s, P1 and F1 i don\'t know what they mean.

#K.E.W by Jesus on 2019-10-11 08:59

Hi I have a KEW 1502v and some body stolen parts so I put all back together but for any reason it not working the heater and I suspected it about the wiring position, and the pressure is stopping and not keep spraying and some times work fine but some times not, one time I fix only with a new clamp …...
Show More

#K.E.W by AUSTIN GIBBONS on 2010-03-30 14:40

CAN I BUY A SPARE PART FOR THE ABOVE, IE, THE PRESSURE WASHER AT THE END OF THE LANCE.?WITH THANKS AUSTIN GIBBONS

#K.E.W by gary appleton on 2008-06-10 15:53

i need new hose

#K.E.W by mark on 2014-10-21 13:50

hi could you tell me where I would get service manual for kew 1640hathanks mark

#K.E.W by Dale on 2009-04-08 00:10

Hi, put a oring kit in pump an still get only tap pressure everything looks good ,keyway on pump motor fine. any ideas. Thanks,

#K.E.W by Hartono on 2011-10-19 06:46

Dear AllPlease give me the information about Services center KEW 0901V In indonesia , for your best cooperation i would to say many thanks

#K.E.W by Antonio Gonzalez on 2012-06-19 13:41

need the service manual of KEW 01K pressure washer

#K.E.W by Kevin Gonneau on 2007-05-07 19:40

Looking for parts manual of help with parts for Unit Model #3803V-103 1985/40No.# 2104067 240v/1/30 ampAny help would be greatly appreciated.

#K.E.W by EdwardKn on 2015-03-27 17:20

Hello. And Bye.

#K.E.W by Rudy Martens on 2009-10-28 06:19

I need a operation manual for KEW 1502v-66

#K.E.W by Adrian Frost on 2011-05-16 11:17

Hi, I have a KEW Steam Cleaner model 16A2V-66 Year 1986. I bought it from a company asset auction and never saw it working. I have now tried to use it and the temperature lights reached the temperature set once, then the burner went out and would not re-light. I dissconnected the fuel supply to the …...
Show More

#K.E.W by Hassan Mortazavi on 2010-10-08 16:23

i just got a used ke w scorpian steam cleaner and everything works exept it does not ignite or no spark to get flame.any idea.thankshassan

#K.E.W by PAUL GALLAGHER on 2008-11-17 21:50

HI,I HAVE JUST PURCHASED A KEW 38A2VA POWER WASHER. IS IT POSSIBLE TO GET A MANUAL FOR THIS MACHINE? ALSO WHAT GOES IN THE TANK MARKED WITH A SNOWFLAKE?THANKS PAUL.

#K.E.W by Hassan. Mortazavi on 2010-10-10 01:05

How do i test the electrod or egniter to see its good?Thanks

#K.E.W by J.den Dekker on 2011-04-03 06:34

Geachte meneer/mevrouw,Ik heb heb kew 1500 hogedruk spuitpart nr. 6137219 Serial nr. 6998760.Kunt u mij vertellen of ik een terrascleaner kan krijgen voor deze hogedruk spuit en als dat mogelijk is kunt u mij vertellen waar en wat hij kost.vr.gr.J.den Dekker

#K.E.W by Owen Torgerson on 2012-03-22 19:12

Great machine, had since new, recently experiencing difficulties acquiring heat.Lots of kerosene, lots of pressure on cold, new fuel spray nozzle...Help

#K.E.W by Blair on 2007-08-15 01:10

call windy city equipment located in Elgin, Illinois

#K.E.W by leo on 2012-10-14 09:11

DO YOU HAVE A SOLUTION FOR THE OIL VALVE FROM THE BURNERIT WILL NOT GO ON BY WORKING WITH THE MACHINEPRESSION KONTAKTS ARE OKE

#K.E.W by shaban limani on 2011-07-02 17:12

JA ICSH BIN LIMANI CSHABAN ICSH BRAUCHE EINE PUMP MACSHINE FOR AUTO VACSH MACSHINE IST FOR MARKE K.E.W 1502V ICSH CHAP MACSHINE ABER PUMP IST KAPUT BITEIN MAINE EMAIL CSHIKENSI DI VORT FOR MAINE RESPEKT

#K.E.W by m j cars on 2011-03-17 11:08

when i turn the machine on it trips the electrick

#K.E.W by Richard Beck on 2009-05-25 21:04

Have a Kew 3803V pressure washer, need to know where I can get itrepaired nearby.thank you

#K.E.W by Josh Campbell on 2005-10-26 14:14

I am trying to refurbish a kew 1502v-66 power washer. I cannot get the oil fired burner to kick on. The control panel has a digital temp gauge and it shows the temperature of the water at its maximum value when the water is cold. I am in question if this is the problem with the burner not firing. I …...
Show More

#K.E.W by brian breslin on 2009-10-14 19:43

where might I download a user manual for parts and maintenance of my 1640h Thanks Brian

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.