Graseby/Goring-Kerr Service & Repair Forum

Dear sir : We are Corner Corporation in Taiwan. We moved our Parmasol aerosol can line to Mainland China and found problems of E-30 checkweigher as follows : 1. The reading of weiight of single product goes up and down,is unstable. 2. When trim calibraton , there were some weight reading of product over 5% of standard weight. And some of good product be rejected. Can you advise what caused it and can you send engineer to help us fix the problems. We already sent e-mail to you several days ago, and didn\'t receive any messages yet. Waiiting for your reply and thanks. Best regards,Victor Chang

— Posted by VICTOR CHANG on 2011-07-01

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Graseby/Goring-Kerr"

If you need your Graseby/Goring-Kerr unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 85 Comments

#Graseby/Goring-Kerr by Kornelia Degorska on 2012-09-05 10:11
I\'ve lost password of DSP2, metal detectorpassword seed number:Operator: 12345678Supervisor:23456781Engineer: 34567812Service: 45678123Please send me the passwordsBest regardsKornelia.
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:38
Did you get your manual? The Tektamet has 2 main circuit boards, power supply board has 2 LED\'s on it, red and green. Is this right?
➡️ Reply
#Graseby/Goring-Kerr by Prakash Panchal on 2015-07-10 07:20
We required user manual for Graseby/goring Kerr Metal detector R-1940607.
➡️ Reply
#Graseby/Goring-Kerr by SWITU PATEL on 2009-04-05 05:26
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Ron Giesbrecht on 2009-06-24 22:07
I recently bought a used GK DSP 2. Do you know where i could get an owners manual?Thanks
➡️ Reply
#Graseby/Goring-Kerr by Dennis Dahle on 2011-07-19 15:14
Good morning we have a TEK21DSP metal detector Is there anyway I could get some information on it. It has run beautifully for years and years but there is an issue right now (there is no signal) We changed the fuses. We just don\'t know what else to do. Thank you for your help Dennis
➡️ Reply
#Graseby/Goring-Kerr by John Lindquist on 2010-04-14 16:43
I need a quote (price and delivery) on the drive and idler sprockets for the mattop belt on your unit # 72CS20INT, serial # 12873/3358. They have square bores and there are 15 0f them.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by Melissa Frelka on 2012-06-11 18:46
I need a Goring Kerr Tek 21 manual.
➡️ Reply
#Graseby/Goring-Kerr by greg waters on 2010-01-23 14:02
NEED TECHNICAL MANUAL
➡️ Reply
#Graseby/Goring-Kerr by John Beddard on 2011-06-21 13:58
Can you supply a contact number in the uk so that we can get one of your technical people to look at our machineType 2022Serial number 56798-3Best regardsJohn Beddard
➡️ Reply
#Graseby/Goring-Kerr by DARLENE CARTER on 2011-03-01 12:37
AM NEEDING MANUAL FOR MODEL 300 GORING-KERR. SER#17913/3tHANK YOU
➡️ Reply
#Graseby/Goring-Kerr by christian on 2011-06-15 18:56
HelloI need a manual for a Goring Kerr DSP2.Can you help me?Best regardsFrode
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:41
Hi, did you locate a manual?
➡️ Reply
#Graseby/Goring-Kerr by Byron Moran on 2012-11-06 15:36
DearsWe need price of metal detector with belt conveyor for cartons of frozen strawberries (-20°C) (10 kg). boxes measures are:500 mm X 500 mmThe metal detector will be at 18 °CBest regardsByron MoránSEVIND
➡️ Reply
#Graseby/Goring-Kerr by Irfan on 2009-12-29 08:17
We would like to have some technical details of Best checkweigher D30.
➡️ Reply
#Graseby/Goring-Kerr by tho on 2009-11-17 19:23
We have second hand Goring Kerr metal detector DSP 2. Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level ?Seed number : service : 45678123We wish receive your answerBest regard…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by vic chiavola on 2008-06-13 15:26
I need an operating/Installation manual for a Graseby/Goreing-Kerr TEK-21 DSP Model Metal Detector.
➡️ Reply
#Graseby/Goring-Kerr by Jose Luis Perez Contreras on 2011-11-25 19:34
Serian tan amables de venderme manual de usuario y o servicios del detector de metales Graseby/Goring-Kerr Tek DSP.Gracias por su atencion.Jose Luis Perez Contreras
➡️ Reply
#Graseby/Goring-Kerr by Brian Large on 2009-01-21 15:54
I have a Graseby Goring Kerr metal detectorMD: 60ALINTKSer: 10531/3046I am looking for any manuals that are available for this machine.Thank you,Brian LargePacific Foods19480 SW 97th Ave.Tualatin, OR 97062503 692-9666 ext. 1417Cell 971 218-5147
➡️ Reply
#Graseby/Goring-Kerr by Jesus Lamas on 2010-09-10 14:17
there is a fault \"search head\" I can not enable this fault.
➡️ Reply
#Graseby/Goring-Kerr by mario cardona on 2007-12-20 17:07
I have a problem with a graseby goring-ker dsp 2s, when I turned it on it makes a noise (alarm) and i can not quit this alarmI want to know if you know something about this problem because I do not have a manual to rapair this machine
➡️ Reply
#Graseby/Goring-Kerr by Edson Soares on 2009-03-02 16:45
Hello Giorgio, can you help me?I need an operating manual for Metal Detector Goring Kerr DSP-2 to, you have?Please contact me.
➡️ Reply
#Graseby/Goring-Kerr by serkan acar on 2009-06-26 07:16
We have 55358 serial metal dedectorsGraseby/Goring Kerr we need operation manuel and test partsBest regardsSultar Agriculture ProductsSerkan ACAR
➡️ Reply
#Graseby/Goring-Kerr by rob on 2011-06-30 17:59
Call Malcolm at DRM Weighparts on 44 (0)1527 558899 tell him Rob passed on his contact details. I n the meantime I have a few bits and pieces myself having been in th egame for a number of years e-mail me if you have any requirements I will check out what I have got.
➡️ Reply
#Graseby/Goring-Kerr by Chris Grabarkievtz on 2010-01-27 17:20
My company had purchased 2 dsp2 metal detectors from an auction. We ordered the Operating and Instruction Manual. I need several parts just to get one of them working. I need the belt drive motor, a 7 pin harness from the motor to the control board, belting for the conveyor, also a wiring diagram wo…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Tatjana on 2009-05-06 22:39
Hi Could you please provide us with an operational manual for Goring Kerr Tek 21 DSP.We could not locate it in the plant
➡️ Reply
#Graseby/Goring-Kerr by Joseph Cooney on 2019-09-25 20:49
Looking for the operational Manuals
➡️ Reply
#Graseby/Goring-Kerr by Rupender Rana on 2009-01-08 14:10
I have a problem with machine that is with calibrationwhen calibrate it in full calibration goes okay load cell gives proper output signal but again when try to do dynamic calibration its not gives any signal or value,,nothing happen on screen turn to weigh mode its shows the fault weigh plate is no…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Cristobal Perez on 2011-04-01 00:00
In my factory, I have a metal detector Graseby/Goring-Kerr, wihich Ican not to calibrate, because I don\'t have the password.I don\'t have the manual.Please, send the manual and the password to my email.Regards
➡️ Reply
#Graseby/Goring-Kerr by Dominic Patry on 2009-09-02 18:21
Hello,I\'m looking for a manual of a Graseby Goring/Kerr CDX 240 X-Ray machine. If you can sell me a copy of this manual.Thank you!
➡️ Reply
#Graseby/Goring-Kerr by Jesus on 2010-09-09 21:31
There is a fault in a metalcheck goring kerr tek 21, the fault is \"search head\" I can\'t not enable this problem
➡️ Reply
#Graseby/Goring-Kerr by RANDY P LAFORTEZA on 2011-06-16 19:46
i need a parts list for local start-stop button(the whole unit including box) for dsp3 metal detector.
➡️ Reply
#Graseby/Goring-Kerr by matthew lamontagne on 2009-12-21 05:27
If you can send me a parts breakdown of dsp-2 goring kerr it will be appreciated greatly. Thanks, Matthew Lamontagne
➡️ Reply
#Graseby/Goring-Kerr by Mayank Agarwal on 2009-04-13 10:05
Hi, This is Mayank from India(Makson\'s Nutrition),We posses a metal detactor by you,request you to send a manual for its operation. As it is not working properly.Serial No:4833RegardsMayank00919302611867
➡️ Reply
#Graseby/Goring-Kerr by Juan Briseno on 2008-11-04 20:21
Hello, my name is Juan Briseno and I am a seller on Ebay (OB20_2). I got a hold of the following eqipment, and I was wondering if you were interested in buying them.3 Goring kerr TK7905 power supply board2 Goring Kerr DSP 1 control panel2 Goring Kerr DSP 2 control panel3 Goring Kerr DSP 3 control pa…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Derek McDonald on 2009-02-05 09:39
Do you know of an agent in the UK that can assist us in locating an operating manual for our checkweigher serial# 12739707
➡️ Reply
#Graseby/Goring-Kerr by Serkan ACAR on 2009-06-26 07:24
We have second hand Goring Kerr metal detector (but we dont know which model is this) with serial no 55358 Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level so I can access th…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by JOHN PUCELLA on 2008-06-01 20:37
I need an operating/illustration manual for Goring Kerr metal detector with band and nuematic reject system
➡️ Reply
#Graseby/Goring-Kerr by nazeer ahmed on 2008-09-06 08:48
WE are leading manufacturers of biscuits in pakistan. we are facing problem at one of the units of mode s7683 metal detector machine as the touch panel has turned scrambled and no menu ia thus being shown on the screen.can you please advise at earliest to resolve this fatal problem.
➡️ Reply
#Graseby/Goring-Kerr by Steve Brady on 2008-09-24 16:39
I am interested in purchasing manuals for a Greaseby/Goring Kerr metal detector. Model# DSP-2, Serial #22519, If you can help with this please respond. Thank you S. Brady
➡️ Reply
#Graseby/Goring-Kerr by Carlos Ortiz on 2006-08-05 14:36
Hi, We need new parts TK7951ISS.F rev. 1993 Display Board and TK7950 R.F. to Digital Board. What I need to do?
➡️ Reply
#Graseby/Goring-Kerr by ourang on 2009-02-25 09:34
Dear Sr or MadamThis is Ourang Batmanghlich from solico meat product.I am technical manager.We have a check weigher machin from GRASEBY type BEST D30.we need user manual this machin.Please send me .Tank you
➡️ Reply
#Graseby/Goring-Kerr by Laura Machin on 2009-01-13 12:01
Srs. Graseby/Goring KerrI´m Laura Machin from Solvay pharma company. We are looking for the TSK DSP metal detector oparating manual. Maybe you can help us.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by mario valente on 2009-03-31 14:37
I bought a used metal detector but have no manual, can you please find and send one to me. tks, regards,
➡️ Reply
#Graseby/Goring-Kerr by Suban Kotrbuppha on 2011-02-22 13:06
We need the manual of metal detector of GRASEBY GORING KERR model : TEK DSP (52528)Thank for your advance
➡️ Reply
#Graseby/Goring-Kerr by Ken Melech on 2008-10-23 23:24
We have recently purchased a second hand Graseby Goring-Kerr Metal Detector, model DSP2. We did not receive an operating manual with the machine. It has been inspected, so we know it is functional, but we cannot have the computer programmed without the manual.Please advise if a manual is available o…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Dean Curbishley on 2012-08-27 13:38
pass code is ZBZB
➡️ Reply
#Graseby/Goring-Kerr by Bushra Latif on 2008-08-13 10:49
We has a Metal Dedector of Grasbey Goring KerrModel ....DSP 2 S.no .....56928-2110 v s/phase 50 HZ Full load 0.4Akindly inform us if you have its operating and instruction manual..Thanks And Regards Bushra Latif Asian Foods Industries Ltd
➡️ Reply
#Graseby/Goring-Kerr by Mark on 2011-05-25 16:00
Does anybody know the special password required for the system config ?
➡️ Reply
#Graseby/Goring-Kerr by Giorgio Araujo on 2008-06-23 15:46
SERIAL : 48886 We need by PDF your instruction operation manual of your Graseby/Goring Kerr TEK DSP - Serial 48 886 110 volts.Thank you in advance!!We have two units and need your operation manual asap. Preferable in Spanish. But if not, in English is fine.Sincerely,Giorgio Araujo.Miami, FLA.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.