Rittenhouse Service & Repair Forum

Hellohave a 520 Beverly and it is working but I took it apart and found the rubber grommets and the felt strike pads are bad i am looking for replacements.ThanksChris

β€”> Purchase or Repair: Ticket Image

β€” Posted by Christopher Cruz on 2011-03-09

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by Andrew Lazazzera on 2018-02-05 18:04
Have Model DS-2 Door Sentry w/ 16v. chime transformer -Rittenhouse #30 or = need local chicagoland technician to trouble-shoot the control box w/ its transformer.-believe transformer is problem.

β€”> Purchase or Repair:
#Rittenhouse by villanes on 2015-09-04 21:54
The Rittenhouse C8578-1 135-7351-01 door chime is malfunctioning and needs repair. Urgently seeking a technician to address the issue as it's disrupting daily operations.

β€”> Purchase or Repair:
#Rittenhouse by Jeffrey on 2008-11-22 22:27
This problem may be caused by a lighted doorbell. After the bell is wrung, the light will re-illuminate. When that happens it may be drawing just enough power to make the door chimes think that the button was pressed once again. This is a repeating pattern.If a lighted door button is used, the solut…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Eddie Rodriguez on 2019-10-13 21:47
I have a Master Model 631 & 632, The clock stop working. its showing the red dot on the face of the clock that indicates power failure. The chimes still work fine with no issue. Can you provide instruction on how to test and/or repair. Thank youEddie

β€”> Purchase or Repair:
#Rittenhouse by Diane McCracken on 2010-10-26 15:22
Do you sell parts? I am looking for a replacement potentiometer for an Emerson-Rittenhouse RC 633. It is labeled Clarostat 140-6747/ 135-51.

β€”> Purchase or Repair:
#Rittenhouse by k. chang on 2009-06-17 02:34
how do we get this old door chime to work again?we\'re already replacing the batteries, what else should we do?thanks

β€”> Purchase or Repair:
#Rittenhouse by James Short on 2013-02-24 20:40
A plunger on my 50 year old door chime is not returning to the rest position when the door chime is not activated. The consequence is a continuous buzz and erratic operation when the button is pressed.Have I provided sufficient information to diagnose the ease of repair?Thank you.Jimβ€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by neil Berman on 2009-07-08 05:25
I have a Rittenhouse Model S7806 Smoke/Fire detector system in my 3-level condo. It was there when I moved in so there is no manual for it.My problem is, after a thunder and lightening storm the other day, I came home to find all 3 units ringing. The only way I could silence them was to switch off t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Tracy BROWNING on 2017-01-13 09:02
I have an old Rittenhouse door chime that is missing it's tubular bells. Home built in 1932. Chime cover has two decorative brass musical notes and a few horizontal brass what look like pinstripes. After researching, I believe it's 30's vintage and original to the home. I would love i…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by v on 2007-06-19 19:52
my dilemma also. have you found a suitable replacement? thanks.

β€”> Purchase or Repair:
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by sonny sadler on 2011-11-21 16:12
i would like to have an updated model the one i have was installed in 1977 it makes noise, drifts off stations all controls are noisey and sound is garbled. can you tell me where to get help.

β€”> Purchase or Repair:
#Rittenhouse by ElectraChime on 2017-01-22 03:43
I can make new bells for this chime. See my sites: doorbellmuseum.org and electrachime.comBestRobert

β€”> Purchase or Repair:
#Rittenhouse by Mark on 2017-09-04 20:48
I'm looking for a replacement circuit board for a Rittenhouse model C8538. Please let me know where I can purchase one.

β€”> Purchase or Repair:
#Rittenhouse by Delia Castillo on 2008-07-29 03:14
we bought this house with installed system. not working. power source not found.

β€”> Purchase or Repair:
#Rittenhouse by Charles Sumrell on 2018-06-16 18:05
Tag on door chime unit says:Model 8846RVolt 16Rittenhouse Division Spartan ElectricFayetteville NC 28386The unit has four tubes, it has a circuit board with integrated circuits. The transformer is putting out 18.5 volts, although the unit says 16 volts on transformer and circuit board. I assume the …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Kathy Grant on 2018-09-24 16:43
I recently purchased an older home that has a Model # RC-475 - 16 volt door chime that works fine, but lacks the cover. Is it possible to purchase just a cover from you or is something like this no longer available. Amazon has one but the mfg. dimensions wouldn't fit. As close as I can measure …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by randy connelly on 2010-04-12 00:59
I need a Rittenhouse door bell botton part number C8000. Is this womethign you may have?

β€”> Purchase or Repair:
#Rittenhouse by O. H. Towers on 2010-01-25 16:00
We are also electrical contractor company(Towers Electrical Serv. Inc)We are looking for a model C8931 R Chimer Receiver also a sender unit if possible.We cannot find any info on this item it was made ty Rittenhouse Fayettevilole, nc. 28302

β€”> Purchase or Repair:
#Rittenhouse by ann chamberlin on 2010-03-07 15:43
Jennifer Walker:Did you ever figure out what to do about replacing your Rittenhouse unit? I\'m in the same boat!Any ideas or products you have come across on your own would be appreciated

β€”> Purchase or Repair:
#Rittenhouse by Harry Yagi on 2017-05-11 12:40
Due to the worn-weakened spring on the hitting bar which do not pop out from the solenoid hole. Do you sell the spring or the entire solenoid with the hitting bar?

β€”> Purchase or Repair:
#Rittenhouse by Richard Baer on 2012-03-06 23:58
This unit puts out a chirping sound (Similar to sound of a smoke alarm) on a continuous basis, one chirp about every 30 seconds. Please advise what I should do, short of disconnecting the unit, to stop this annoying sound.Thank you,Richard Baer

β€”> Purchase or Repair:
#Rittenhouse by Earl Miller on 2012-10-11 01:23
Is there a new updated unit (with new bells & whistles) that can use the existing wiring and wall recesses of the old units. If so, where can I get them and what would be a ballpark pricing? Thanks

β€”> Purchase or Repair:
#Rittenhouse by Wendy Morris on 2010-01-15 06:14
Our current cover is kind of an almond color. After remodeling our living room, all of the vents, outlets, etc. have been done in white. Would it be possible to purchase a white cover to replace the almond one for our door chime? What would the cost be?Please respond even if not available before I r…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jorge Crespo on 2015-05-11 04:05
Riitenhouse chime model C8538R to connect into the AC adapter 16 volt .

β€”> Purchase or Repair:
#Rittenhouse by bill whitacre on 2013-11-16 18:30
need to reconnect wires to front, rear & trans positions.

β€”> Purchase or Repair:
#Rittenhouse by Barb C on 2009-03-27 12:35
Same as James Mann note - have 1970\'s Rittenhouse intercom---can we replace old system - can we purchase new units but use same wiring??

β€”> Purchase or Repair:
#Rittenhouse by Patsy Goodwyn on 2014-09-27 23:39
We need to replace the long tubes on these chimes. They are look bad and we have lost one of them. Do you have the 4 tubes to replace the old ones with? If so, how much are they? Patsy

β€”> Purchase or Repair:
#Rittenhouse by Jim Fields on 2012-11-19 16:03
I have a schematic for Models M7010, M7011, M7012, M7020. The document also has AM Alignment, FM Alignment, Troubleshooting chart, and list of replacement parts for printed circuit board.

β€”> Purchase or Repair:
#Rittenhouse by Tom Gleason on 2011-03-31 01:27
Looking for a sequencer box for a model 552 doorbell chime. I know they are rare. Does somebody make a retro fit or do you have a good used one. If none of the above then how about schemetics and I will get one made. Thanks-Tom

β€”> Purchase or Repair:
#Rittenhouse by Starla Irvin on 2022-03-20 00:17
Moved in 3 years ago the AM/FM worked but nothing else. Wondering if I could get an estimate

β€”> Purchase or Repair:
#Rittenhouse by Donald Brown on 2017-07-07 23:15
I need to have a bulb replacement performed on a 1980ties vintage bronze doorbell. The spring works fine but light nolonger stays on.Regards, Don

β€”> Purchase or Repair:
#Rittenhouse by James A. Mann on 2008-06-26 12:40
We installed our Rittenhouse intercom system in 1978 when we built our new home. The speakers look out of date and would like a better main unit. We have 4 outside units, and 7 speakers.Can we purchase new units and still use the same wiring? Would appreciate a response ASAP. Thanks Jim MannP.S. Ple…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jolene Gross on 2015-08-16 14:22
I have a Rittenhouse model c8229 door bell in my home that is not working. I would like to have it repaired.Thank you,Jolene Gross717-781-3692

β€”> Purchase or Repair:
#Rittenhouse by Bob on 2007-04-07 23:14
We have the same system in our home. Did you find any compatible system? Did you replace your system? If so, what system did you use? Thank you. We need to replace everything except the wiring.

β€”> Purchase or Repair:
#Rittenhouse by LINDA BURGESS on 2017-03-30 17:16
Have model C 8203, 10 volt door bell. Am missing the push button remote that fastens to wall outside the front door. Any suggestions?

β€”> Purchase or Repair:
#Rittenhouse by Lynn Villano on 2011-05-06 13:29
but want door bell to continue working. Can we get wiring schematics?

β€”> Purchase or Repair:
#Rittenhouse by R.Sarin on 2010-08-11 23:11
Hi I need a cover for the rittenhouse door chime model 380 can u pls get back to me thank you

β€”> Purchase or Repair:
#Rittenhouse by Barbara on 2006-08-27 17:45
This is an old system I would like to replace. Does the wire plugs have to be replaced. I would like sm=omthing that will be compatable with the wire plugs. Do you have any suggestionsThank You

β€”> Purchase or Repair:
#Rittenhouse by dominic Carini on 2009-07-28 00:55
Ihave about a 30 year old rittenhouse with 4 chimes.It seems that the solenoids that activate the strikers,are getting a little lazy.I have had one apart and try to clean it ,with not much succes,I even lost one of those tiny springs. I tried to replace it with a similar one ,but it\'s not right.Do …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Mickey Loveria on 2007-08-30 14:53
Existing model was put in my home maybe late 60\'s, with ivory base unit and 4 ivory receivers plus brass door unit intercom. The radio reception is irregular, fades in and out and there is much static. Sometimes have to jiggle knobs on base unit to tune radio! Any suggestions on where to go for upg…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Larry Yudkowitz on 2020-05-13 00:16
I have Model 380 16V. I had connected it ot a Ring Video 2 Doorbell and it worked fine for several months. Now there is a loud humm coming from the chime. I think the Ring ihas a problem. Ring says the chime may not be compatible. Ring says the model 382 is compatible. Whould you know the difference…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Chuck Duncan on 2013-03-20 00:33
Was working well until I sanded and painted the kitchen. I took the chimes down to paint, put them back and nothing works. I get voltage coming in but it doesn\'t move anything.

β€”> Purchase or Repair:
#Rittenhouse by Derek Rust on 2008-07-26 15:22
I am interested in buying your intercom, I had mine accidentally ripped out during remodelling and need a replacement , does yours work ok?Derek Rust

β€”> Purchase or Repair:
#Rittenhouse by John Zeitler on 2012-12-05 22:32
I am looking for the cover that is a black plastic 8 3/8\" wide, 5 1/2\" high, and 2 1/8\" deep. Any idea where I can find a suitable replacement? Thanks.

β€”> Purchase or Repair:
#Rittenhouse by Joseph LaBarbera on 2012-06-11 14:33
Would like to know if there is a replacement for this unit or where I can find a replacement knob for the Talk Listen stalk.

β€”> Purchase or Repair:
#Rittenhouse by Terri McDougall on 2012-04-06 14:55
Our house was built in 1978 and we purchased it in 1997. It had the Rittenhouse monitor system in place with the main unit in the kitchen and smaller units scattered thought the house and in an attached apartment. The unit has never worked since we have been here and I was wondering if it is repaira…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by william j paveletz on 2018-03-09 19:10
i need a part model c8633 volts 16 need the main eletric gear

β€”> Purchase or Repair:
#Rittenhouse by craig cipriani on 2011-11-03 15:22
I hav a door chime and clock rittenhouse model 631 and 632 i need a wiring diagram for. any help i can get is appriciated thank you

β€”> Purchase or Repair:
#Rittenhouse by Gord on 2011-11-24 21:00
Jessica:I have the same model door chime, with the same problem. How did u make out with yours? Do you know any of the history of this chime. From what I can surmise, it was produced after WW2 and that would fit as it was in my parents house when i was born in 1954. I have a friend that is an electr…Purchase or Repair: Ticket Image...
Show More

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.