Agie for Service call 1-336-969-0110 at Industrial Electronics Repair

Agie Service & Repair Forum

Hello We have a Agie sinker that has beenj acting up for awhile and here recently we are not able to use the machine. We have had problems with referencing the machine where the y axis goes the the zero then starts to go in the wrong direction to reference. Now it will go down to burn and will stop then drop down a couple 100 thousands of an inch after shutting off. I also am having problems with fine detail on an electrode eroding detail off the part. Do you do service on the field and what would be the cost to look at the machine and give an estimate at repair cost. Thank You David

— Posted by David Woods on 2019-08-01

Reply🗨️Ask a New Question Below❓

If you need your Agie unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 28 Comments

#Agie by Rafael Angel on 2009-09-26 19:40

AGIE Mondo Start 20 CNC EDM with control AGIE FUTURA V EC4 Power Supply and control.Machine and control abandoned in an hazard enviroment for almost 3 years

#Agie by james dow on 2009-12-24 03:02

are you still in need? I am a former Agie techwith 18 years experience with Mondos.

#Agie by Eric Szewc on 2010-02-17 00:18

I\'m trying to hunt down schematics for this control so I can diagnose the problem. Do you have any expierience with these controls? I seem to have a power issue. I just picked the machine up, wired it in and when I powered it up the capacitor/resistor filter on a contactor smoked. I removed them fr...
Show More

#Agie by Jimmy Gray on 2010-06-08 22:37

LOOKING FOR SOFTWARECOPY OF HARD DRIVE FOR MONDO 20 AND MONDO STAR 50CAN ANYONE HELP?

#Agie by Dave Archer on 2010-09-21 14:32

We have a Pendant control that need repaied for our Agie-Elox Mondo 2. Can you help?

#Agie by Puneet batra on 2011-03-19 10:54

Hi I need the following items.for Agiecut Ac250SF for MMD-SF1 AMS M45(VMI)2 AMS M350(Hard Disk+PCB)orP5-75 for MMD id no. 699.334.9FW 10.03Thank you

#Agie by kannan.a on 2011-04-02 12:17

Dear sir ,i have agietron mondo, and agitron 50both machines are under srevice .nobody is here to do the servivce.can you help me for that,st command is coming in agietron 50thank youkannan.a

#Agie by Yolando O.Cotejo Jr. on 2011-06-16 07:04

We had a problem in our EDM, do you have a support here in the philippines to visit our company. This is my number(0917)633-0410.

#Agie by Kimberly Donozo on 2011-06-16 08:12

The AGIE MONDO STAR is down for 2 days. We tried to check the videocard then it turned out ok. My concern is where can I find supplier of the motherboard? I need to replace it as soon as possible.

#Agie by James Dow on 2011-07-20 00:08

still need help with motherboard? I am a 12 year Agie service tech.call me at 413-221-0761

#Agie by yap on 2011-08-16 13:09

i would appreciate if can quote me the software .The hard disk is good ,but no software is in . if i can purchase the software and download it ,let me know the cost .if you need the picture ,let me know.please email to camda88@gmail.com and cc to yapkh8@streamyx.com thank you regards yap

#Agie by yap on 2011-08-16 13:20

hi .i would appreciate your help .i need the software of agie mondo star 20 .futura V. can you help .i will pay you if i can download it from you ,the hard disk is good .2nd, where can i download the operation manual .Regards Yap

#Agie by yap on 2011-08-18 05:43

dear sir ,i would appreciate if you can help me out .I would like to purchase the software for the machine above .I have 1 unit ,agie mondo star 20 cnc edm the hard disk is good but there are no software in it,in other words no operation software .if you need some pictures ,let me know . Also if you...
Show More

#Agie by yap heng on 2011-08-21 14:41

i have some problems on the above machine .please contact me or let me know how to contact you .fault : power ON emd machine .display shows \"BOOT FAILURE \"my email address camda88@gmail and yapkh8@streamyx.comregards yap

#Agie by Oscar Huelgas on 2012-03-11 19:01

I am looking for someone who can come to my factory and help us repair our unit.

#Agie by Mike Jacquemin on 2013-01-08 12:57

Looking for Jim Dow to call me at Seitz LLC 860-489-0476 ext 129

#Agie by Thanh Nguyen on 2013-01-24 16:55

I need to repair an Agie hand box. Please contact me as above info.Best regards,

#Agie by Thanh Nguyen on 2013-01-24 17:09

I need to repair an Agie hand box. Please contact me as above info.Best regards,

#Agie by Mr Viet on 2013-04-09 06:52

dear sir ,I would like to purchase the software for the machine above .I have 1 unit ,agie mondo 50 (futura IV control) cnc edm the hard disk is good but there are no software in it,so i can\'t operation software. Please help me, thank you!

#Agie by Thanh Nguyen on 2013-06-03 12:40

Can you repair an Agie 123 handbox?Please contact me at 215 766-8853 extension 1238 or email me at the address listed above.Best Regards,

#Agie by Huan Le on 2013-06-10 20:04

Agie Sprint wire EDM wen t down, alarm #739 Generator is defective. Can you help ?

#Agie by Brian Connor on 2013-10-17 12:26

Do you trouble shoot and repair older Agie machines ie AC50?

#Agie by MALCOLM MACDOUGALL on 2015-09-04 20:54

our keyboard fell apart when it was removed for servicing our Agie Sprint. Apparently the glue that was holding the membrane to the board dried out due to the age of the machine and now it will not make contact with the keys. Since the machine is no longer supported by GF Agie I need to find either ...
Show More

#Agie by Ron McCracken on 2016-12-28 20:31

I am looking for wiring diagram for an Agie Spirnt 20. Is this something you can help me with?Thanks Ron

#Agie by David Woods on 2019-08-01 20:01

Hello We have a Agie sinker that has beenj acting up for awhile and here recently we are not able to use the machine. We have had problems with referencing the machine where the y axis goes the the zero then starts to go in the wrong direction to reference. Now it will go down to burn and will stop ...
Show More

#Agie by Bruce Byrnes on 2019-08-13 14:23

On start up get E60 error, "PACER" failed. I think it is a bad motherboard. If that is the problem Is that something you could repair? If you think it is something else let me know.Thanks Bruce

#Agie by Christopher Clifton on 2019-09-10 18:47

Hello my name is Shayne Clifton. We have an older Agie Mondo 50. For some reason after it starts sometimes it will just freeze. Its happening very frequently. I cant move the machine or anything. I need a tech out this way and didnt know if you service our area and could give us a quote. Regards.Sha...
Show More

#Agie by rusty cummings on 2019-11-22 12:39

Hello my name is rusty I work in a shop and I have a agie remote pendant that will not work

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.