Agie Service & Repair Forum
I\'m trying to hunt down schematics for this control so I can diagnose the problem. Do you have any expierience with these controls? I seem to have a power issue. I just picked the machine up, wired it in and when I powered it up the capacitor/resistor filter on a contactor smoked. I removed them from the circuit and the machine powered up and everything was operational except machining voltage. after a few days of tracing the circuitry a resistor fried on the power distribution card. I have no books for this so I\'m just flying blind.Eric
—> Purchase or Repair:
Reply🗨️Ask a New Question Below❓
Recent Comments Search: "Agie"
- Agie → Agie ↗
- Agie → Agie AC50 ↗
- Agie → Agie Elox Mondo 2 remote pendant repair ↗
- Agie → software for Agie Mondo star 20 Futura V cnc edm ↗
- Agie → motherboard ↗
- Agie → Agie Agie Sprint 20 ↗
- Agie → agie repair ↗
- Agie → Agie 123 Handbox. ↗
- Agie → software ↗
- Agie → Agiecut 100 needs service and repair ↗
- Agie → Agie repair control of an AGIE Mondo CNC EDM machine ↗
- Agie → service ↗
- Agie → Agie AGIE MONDO 20 AND 50 ↗
- Agie → AGIE MONDO STAR MOTHERBOARD REPLACEMENT ↗
- Agie → agie mondo star 20 cnc edm futura V ↗
- Agie → need PCB ↗
- Agie → Repair of Agie Mondo Futura V ↗
- Agie → Agie Agie Elox Mondo 2 Pendant Control ↗
- Agie → software of mondo 50, Futura IV control ↗
- Agie → agie mondo star 20 futura V cnc edm ↗
- Agie → Agie Agie hand box repair. ↗
- Agie → Agie 613.960.4 ↗
- Agie → Agie Agie Mondo Star 20 repair ↗
- Agie → Agie mondo star 50 ↗
- Agie → Agie KEYBOARD 192657 FOR AGIE SPRINT 20 WIRE EDM ↗
- Agie → Agie Agie Mondo 50 Sinker ↗
- Agie → Agie 638.864.9 ↗
- Agie → New Agie ↗
- Agie → Agie Agiepuls 30L control ↗
If you need your Agie unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110
Recent 30 Comments
We had a problem in our EDM, do you have a support here in the philippines to visit our company. This is my number(0917)633-0410.
—> Purchase or Repair:
—> Purchase or Repair:
The Agie 613.960.4 PMO-05 Power Board unit is exhibiting erratic behavior in the warehouse.
—> Purchase or Repair:
—> Purchase or Repair:
On start up get E60 error, "PACER" failed. I think it is a bad motherboard. If that is the problem Is that something you could repair? If you think it is something else let me know.Thanks Bruce
—> Purchase or Repair:
—> Purchase or Repair:
quick update about the Agie 638.864.9 unit - the HPS-03 High Power Supply Board malfunctioned during the night shift. Needs attention ASAP in the morning. Thank you!
—> Purchase or Repair:
—> Purchase or Repair:
are you still in need? I am a former Agie techwith 18 years experience with Mondos.
—> Purchase or Repair:
—> Purchase or Repair:
LOOKING FOR SOFTWARECOPY OF HARD DRIVE FOR MONDO 20 AND MONDO STAR 50CAN ANYONE HELP?
—> Purchase or Repair:
—> Purchase or Repair:
We have a Pendant control that need repaied for our Agie-Elox Mondo 2. Can you help?
—> Purchase or Repair:
—> Purchase or Repair:
Dear sir ,i have agietron mondo, and agitron 50both machines are under srevice .nobody is here to do the servivce.can you help me for that,st command is coming in agietron 50thank youkannan.a
—> Purchase or Repair:
—> Purchase or Repair:
Hello my name is Shayne Clifton. We have an older Agie Mondo 50. For some reason after it starts sometimes it will just freeze. Its happening very frequently. I cant move the machine or anything. I need a tech out this way and didnt know if you service our area and could give us a quote. Regards.Sha…Purchase or Repair: 
...
Show More
Show More
Hello We have a Agie sinker that has beenj acting up for awhile and here recently we are not able to use the machine. We have had problems with referencing the machine where the y axis goes the the zero then starts to go in the wrong direction to reference. Now it will go down to burn and will stop …Purchase or Repair: 
...
Show More
Show More
The AGIE MONDO STAR is down for 2 days. We tried to check the videocard then it turned out ok. My concern is where can I find supplier of the motherboard? I need to replace it as soon as possible.
—> Purchase or Repair:
—> Purchase or Repair:
i would appreciate if can quote me the software .The hard disk is good ,but no software is in . if i can purchase the software and download it ,let me know the cost .if you need the picture ,let me know.please email to camda88@gmail.com and cc to yapkh8@streamyx.com thank you regards yap—> …Purchase or Repair: 
...
Show More
Show More
our keyboard fell apart when it was removed for servicing our Agie Sprint. Apparently the glue that was holding the membrane to the board dried out due to the age of the machine and now it will not make contact with the keys. Since the machine is no longer supported by GF Agie I need to find either …Purchase or Repair: 
...
Show More
Show More
Hi I need the following items.for Agiecut Ac250SF for MMD-SF1 AMS M45(VMI)2 AMS M350(Hard Disk+PCB)orP5-75 for MMD id no. 699.334.9FW 10.03Thank you
—> Purchase or Repair:
—> Purchase or Repair:
hi .i would appreciate your help .i need the software of agie mondo star 20 .futura V. can you help .i will pay you if i can download it from you ,the hard disk is good .2nd, where can i download the operation manual .Regards Yap
—> Purchase or Repair:
—> Purchase or Repair:
I am looking for someone who can come to my factory and help us repair our unit.
—> Purchase or Repair:
—> Purchase or Repair:
still need help with motherboard? I am a 12 year Agie service tech.call me at 413-221-0761
—> Purchase or Repair:
—> Purchase or Repair:
I\'m trying to hunt down schematics for this control so I can diagnose the problem. Do you have any expierience with these controls? I seem to have a power issue. I just picked the machine up, wired it in and when I powered it up the capacitor/resistor filter on a contactor smoked. I removed them fr…Purchase or Repair: ...
Show More
Show More
I need to repair an Agie hand box. Please contact me as above info.Best regards,
—> Purchase or Repair:
—> Purchase or Repair:
dear sir ,I would like to purchase the software for the machine above .I have 1 unit ,agie mondo 50 (futura IV control) cnc edm the hard disk is good but there are no software in it,so i can\'t operation software. Please help me, thank you!
—> Purchase or Repair:
—> Purchase or Repair:
I am looking for wiring diagram for an Agie Spirnt 20. Is this something you can help me with?Thanks Ron
—> Purchase or Repair:
—> Purchase or Repair:
Agie Sprint wire EDM wen t down, alarm #739 Generator is defective. Can you help ?
—> Purchase or Repair:
—> Purchase or Repair:
i have some problems on the above machine .please contact me or let me know how to contact you .fault : power ON emd machine .display shows \"BOOT FAILURE \"my email address camda88@gmail and yapkh8@streamyx.comregards yap
—> Purchase or Repair:
—> Purchase or Repair:
dear sir ,i would appreciate if you can help me out .I would like to purchase the software for the machine above .I have 1 unit ,agie mondo star 20 cnc edm the hard disk is good but there are no software in it,in other words no operation software .if you need some pictures ,let me know . Also if you…Purchase or Repair: ...
Show More
Show More
Can you repair an Agie 123 handbox?Please contact me at 215 766-8853 extension 1238 or email me at the address listed above.Best Regards,
—> Purchase or Repair:
—> Purchase or Repair:
AGIE Mondo Start 20 CNC EDM with control AGIE FUTURA V EC4 Power Supply and control.Machine and control abandoned in an hazard enviroment for almost 3 years
—> Purchase or Repair:
—> Purchase or Repair:
I need to repair an Agie hand box. Please contact me as above info.Best regards,
—> Purchase or Repair:
—> Purchase or Repair:
—> Purchase or Repair: