Dresser-Rand Service & Repair Forum

I RECENTLY PURCHASE A USED DRESSER COMPRESSOR MODEL#550-A SERIAL#4017X6925 WITH THE PULLEY,THE UNIT HAS HAD VERY LITTLE USE.THE PROBLEM I\'M HAVING IS THE SMALL COPPER LINES LEAVING THE 2 HEADS GOING TO THE BASE,THEY HAVE BEEN RIP OFF AND I DON\'T KNOW WHERE THEY ALL GO.MY PLAN IS TO USE THIS UNIT IN MY GARAGE WITH A MAX. PRESSURE OF 140 PSI.,WHAT SIZE OF MOTOR DO I NEED,SO COULD YOU SEND A SHEET WITH THE DIRECTION OF THOSE LINES AND THE SPEED IT NEED TO TURN, WHAT TYPE OF OIL ETC. THANK-YOU ...NORM FAX#705-474-3943 MAILING ADDRESS 1522 MAIN ST.WEST NORTH BAY ONTARIO CANADA P1B2X3

— Posted by NORM BLAIS on 2008-05-06

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Dresser-Rand"

If you need your Dresser-Rand unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 6 Comments

#Dresser-Rand by joaquim.aresta on 2007-06-04 17:42
i have a compressor the need some parts were i weel be able to get parts from serie #66As/n 4018x7067
➡️ Reply
#Dresser-Rand by Sam on 2007-10-16 18:15
looking for basic info or specs on a dresser compressor.only have partial tag infothis is the info I can read 400serial # 453X1 238LER(assuming Leroi)Dresser (look like industries) IncSindey Ohio U.S.A.
➡️ Reply
#Dresser-Rand by NORM BLAIS on 2008-05-06 17:35
I RECENTLY PURCHASE A USED DRESSER COMPRESSOR MODEL#550-A SERIAL#4017X6925 WITH THE PULLEY,THE UNIT HAS HAD VERY LITTLE USE.THE PROBLEM I\'M HAVING IS THE SMALL COPPER LINES LEAVING THE 2 HEADS GOING TO THE BASE,THEY HAVE BEEN RIP OFF AND I DON\'T KNOW WHERE THEY ALL GO.MY PLAN IS TO USE THIS UNIT I…...
Show More
➡️ Reply
#Dresser-Rand by joaquim.aresta on 2007-06-18 17:46
i have a compressor the need some parts were i weel be able to get parts from serie #66As/n 4018x7067
➡️ Reply
#Dresser-Rand by shane on 2007-08-04 18:56
What parts are you looking for ?? I,ve found alot of them .....Most of these places like Dresser-Rand won,t help you they\'ll just pass you off to someone else
➡️ Reply
#Dresser-Rand by Jody Hotchkiss on 2010-03-16 04:03
I was told that I need special tool to remove valves. Why such a big deal? I can\'t afford to take chance to rebuld my shit if theirs going to be complacations. Give me some ideas to work on this. This is my money maker, can\'t afford to sit.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.