El.Ge Service & Repair Forum

Dear Sir,I\'ve bought 3 second hand servo drives, EL.GE AZE-CC4Q Tipo AZE LV15/AO-PI am looking for a few weeks for a diagram to connect these, but can\'t find anything. As well i like to know what is the input voltage.Kind regards,Leonard van den Berg

—> Purchase or Repair:

Reply🗨️Ask a New Question Below❓

• El.Ge → EL.GE ↗
• El.Ge → Vickers El.ge servo drive diagram ↗
• El.Ge → vickers aze-cc4q ↗
• El.Ge → An excessive amount of the best thing is AMAZING. ↗
• El.Ge → Enquiry ↗
• El.Ge → aze-cc4q ↗
• El.Ge → manual variador sd/cc 4º s ↗
• El.Ge → AZM BA002 B ↗
• El.Ge → Informacion ↗
• El.Ge → EL.GE DC CONTROLLER AZM BA002 B ↗
• El.Ge → Consulta ↗
• El.Ge → aze-cc4q catalog ↗
• el.ge → El.Ge AZE-CC4Q ↗
• El.Ge → El.Ge electrical drawings request ↗
• El.Ge → Vickers AZE-CC4Q ↗
• El.Ge → El.Ge AZE-CC4Q Tipo AZE LV15/AO-P ↗
• El.Ge → SERVOR CONTROL ↗
• El.Ge → DC servodrive ↗
• El.Ge → AZE-cc4q ↗
• El.Ge → El.Ge AZE-CC4Q Repairs ↗
• El.Ge → El.Ge El.Ge AZE-CC4Q ↗

Recent 23 Comments

#El.Ge by Sven Rookie on 2010-04-20 19:33

I\'v a question regarding the controller:Are there any spare parts for those drives, is there any technical support existing or is there any identical drive which can be used?As USA is quite far away - do you know a technical support in europa?Many thanks for your answer!Kind regardsSven—> …Purchase or Repair: ...I\'v a question regarding the controller:Are there any spare parts for those drives, is there any technical support existing or is there any identical drive which can be used?As USA is quite far away - do you know a technical support in europa?Many thanks for your answer!Kind regardsSven

—> Purchase or Repair:
Show More

➡️ Reply

#El.Ge by Sean Moffatt on 2007-01-02 22:44

I have one of these units in a servo roll feed that drives the brushed DC servo motor just fine. The problem is that it does not respond to the +/- 10V control signal. It runs at 100% randomly in fwd or rev when a start signal is applied. The cnc controller was made in the 80\'s It is no longwer sup…Purchase or Repair: ...I have one of these units in a servo roll feed that drives the brushed DC servo motor just fine. The problem is that it does not respond to the +/- 10V control signal. It runs at 100% randomly in fwd or rev when a start signal is applied. The cnc controller was made in the 80\'s It is no longwer supported (software or electronically), and is basically junk and is going to be replaced with something that is current. I need a estimate for testing and or repairs if possible. Model: AZE-CC4QTipo:AZE LV15/AO-P-110/8,5/24No. Matr.EC 22230Codice:42/88ThanksSean MoffattOperations managerHoffman Mint

—> Purchase or Repair:
Show More

➡️ Reply

#El.Ge by Andrea on 2007-08-01 11:49

We have a old machine with this type of electrical device ,but at the moment it\' s stopped because i have some wrong signal coming (i think)from servo motor D.C AZE LV15 .when the \"speed enable\" signal it\'s sended to AZE device it rest only for a few second and then fall down, this happen when i…Purchase or Repair: ...We have a old machine with this type of electrical device ,but at the moment it\' s stopped because i have some wrong signal coming (i think)from servo motor D.C AZE LV15 .when the \"speed enable\" signal it\'s sended to AZE device it rest only for a few second and then fall down, this happen when i have more then one device connected and able. If i move the motor in manual everythink ok .I tryed to force the enable signal to all the AZE device but they become crazy ...For this i need ,the electrical drawings of \"El.ge AZE CC4Q type AZE LV15\",the wire connection and in case to know if you can sale me one new device after know the price.

—> Purchase or Repair:
Show More

➡️ Reply

#El.Ge by mick Sharman on 2010-04-28 06:53

There are no spares anywhere. The Poletti & Osta brand is the same, just badged and coloured differently. They are the same as El.ge. identical.You can exchange any higher current rating (average and Peak) as long as it is higher rated, but same Voltage. I could not find any of these, but there was …Purchase or Repair: ...There are no spares anywhere. The Poletti & Osta brand is the same, just badged and coloured differently. They are the same as El.ge. identical.You can exchange any higher current rating (average and Peak) as long as it is higher rated, but same Voltage. I could not find any of these, but there was a supplier in UK who had one, but I think it has gone.

—> Purchase or Repair:
Show More

➡️ Reply

#El.Ge by Ing. Jose carlos Pinto Aranibar on 2009-03-04 12:54

Estimados señores, estamos reparando una seccionadora de madera de giben, cuenta con una placa AZE CC4Q, no sabemos si esta esta bien o mal, les rogaria puedan facilitarnos los pasos a seguir o la secuencia de las entradas o si tubieran un data sheet de está tarjeta, para ver si podemos hacerla func…Purchase or Repair: ...Estimados señores, estamos reparando una seccionadora de madera de giben, cuenta con una placa AZE CC4Q, no sabemos si esta esta bien o mal, les rogaria puedan facilitarnos los pasos a seguir o la secuencia de las entradas o si tubieran un data sheet de está tarjeta, para ver si podemos hacerla funcionar manualmente, y asi poder revisar el programa en el PLC,a la espera de sus comentarios:

—> Purchase or Repair:
Show More

➡️ Reply