Elox Corporation : elox table model | Elox Corporation Repair

Elox Corporation Service & Repair Forum

ram will not go up switches work. we had to move it and since then the ram dropped and will not go up. Is it the hydrolics and how do i bleed the air out.

—> Purchase or Repair:

— Posted by michael spacco on 2006-07-18

Reply🗨️Ask a New Question Below❓

Recent Comments Search: "Elox Corporation"

Elox Corporation → manual and filters ↗
Elox Corporation → ELOX ASTRA 50 ↗
Elox Corporation → Fanuc 11 EDM Elox 12 ↗
Elox Corporation → Elox Corporation Support in Mexico ↗
Elox Corporation → ELOX-AMERITRON ↗
Elox Corporation → Elox Corporation manual books ↗
Elox Corporation → elox ameritron ↗
Elox Corporation → Elox Corporation elox edm wire ↗
Elox Corporation → fanuc 15m SV013 Y IMPROPER V_READY OFF ↗
Elox Corporation → Elox Corporation elox hrp 64 manuals ↗
Elox Corporation → manual de maquina elox nps d40 nw ↗
Elox Corporation → CONTROL NUMERIC ELOX FUTURA II ↗
Elox Corporation → diagrama de eroionadora de penetracion t50s ↗
Elox Corporation → Elox Manuals ↗
Elox Corporation → Elox Corporation Technical service ↗
Elox Corporation → Elox Corporation : elox table model ↗
Elox Corporation → Elox-ameritron , we can not start ↗
Elox Corporation → Elox Corporation Used unit for service ↗
Elox Corporation → ELOX J SERIES PARAMETER SETTINGS ↗
Elox Corporation → Elox Corporation manual ↗
Elox Corporation → Elox Mondo Star50 ↗
Elox Corporation → Elox Corporation : manual ↗
Elox Corporation → Elox Corporation Need a manual ↗
Elox Corporation → EDM errors ↗
Elox Corporation → Troble shooting manual for EDM fantastic elox ↗
Elox Corporation → Elox Corporation Manuals ↗
Elox Corporation → Elox Workmaster 45 jog switch panel pinout diagram ↗
Elox Corporation → trouble shooting elox edm ↗
Elox Corporation → Elox HRP-64 ↗

If you need your Elox Corporation unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110

Recent 30 Comments

#Elox Corporation by Salim Miro on 2011-06-28 07:03

I am negotiating to purchase one of your Series O Wire cut EDM machine. I will be shipping it Manila Philippines. Do you have a repair facility in Philippines? If so pleas send the information so we may contact them. Thank you,

—> Purchase or Repair:

#Elox Corporation by Tim Higgins on 2008-12-02 16:46

having trouble with my edm. message \"ps servo control communication failure\" is up and won\'t reset. how can i correct this?machine is 8-2012 cnc sn. 004712 with controll svs11cef58 sn. ps1372 could this be a loose cable/connection, or something more serious.

—> Purchase or Repair:

#Elox Corporation by carlos orru on 2008-01-17 15:23

Dear Srs : recently I purchasse And Elox EDM WIRE MACHINE FROM USA ( Mc Kean Machinery) :and the machine arrived with some electronic problem .the machine is ; Nª serie 718 521 type A O 4b O 219-B211year 1986 -08S/N C -6V0091We do need the ladern diagram ,and also lets me know if you are in conditio…Purchase or Repair:

#Elox Corporation by edwin dulce aguilar on 2009-10-08 19:05

quiero el esquema electrico de este modelo

—> Purchase or Repair:

#Elox Corporation by Adang Rosadi on 2012-07-18 07:36

We have a trouble with our Elox Mondo star 50 EDM machine. Error ocur during axis movement, \" (E48) A short circuit was detected while jogging or positioning\". Would you like to advise us to slove the problem ?Thanks and best regards,Adang

—> Purchase or Repair:

#Elox Corporation by jayesh vasani on 2007-08-30 16:38

We have purchased second hand makino hmc - GE FANUC 15M CONTROLduring starting we found - SV013 Y IMPROPER V_READY OFFSV013 Z IMPROPER V_READY OFFSV013 B IMPROPER V_READY OFFFOR X AXIS THERE IS NO MESSAGEWhat can be the problem ?Pleasge guide usRegards,JayeshIndia

—> Purchase or Repair:

#Elox Corporation by James Dow on 2011-10-08 23:37

Jose,it appears that the battery on the motherboard has gone bad. This meansthat the CMOS has to be reprogrammed so that there is no floppy driveand not to seek floppy drive at startup. Also there are other things thatneed change in the CMOS.

—> Purchase or Repair:

#Elox Corporation by ESTUARDO JUAREZ QUIROZ on 2011-04-13 02:57

THE SYSTEM OPERATION ERROR.MESSAGE:INSERT DISKET A:PLEASE SEND INFORMATION.BEST REGARDSTHAN YOU.

—> Purchase or Repair:

#Elox Corporation by RLH on 2010-02-18 14:00

We have an ELOX J series wire edm that we need to set the parameters for wire tension and flush control.We had to replace a circuit board and tried to reload the parameters via tape too floppy but with no sucess.Is there a way to load these manually?

—> Purchase or Repair:

#Elox Corporation by P.M.C.J.Peters on 2006-07-27 13:27

To the manual: is it related to the machine?What is de problem that you have?

—> Purchase or Repair:

#Elox Corporation by Ron Clausen on 2012-06-06 13:48

we have a Mondo Start 50, ser # M50 STAR-002181, another is U06.690.8 would like to know how many gals of fluid does it take and /or a downloadable manual.Thanks

—> Purchase or Repair:

#Elox Corporation by Rodrigo Avendano on 2006-03-08 22:45

Dear friend. I need aid to ignite 12 EDM ELOX HERITAGE FANUC 11This blocked and I cannot operate it single the board and screen. it throws the following errors to me: TM 020 Z-AXIZ BRAKE ENGAGED X EXCESS DRIFT COMPENSATION And HND STOP***************LSK EXCESS DRIFT COMPENSATION to know since I make…Purchase or Repair:

#Elox Corporation by LEN JOHNSON on 2010-09-23 13:36

RAM CYCLIER CANCELS BURN WHEN STARTED. REPLACED PUSH BUTTON BUT IT DOE\'S STILL CANCELS BURN.

—> Purchase or Repair:

#Elox Corporation by Jim McNamara on 2008-05-14 18:54

You can obtain copies of most Elox manuals by contacting:EDM Zap Part, Inc.1108 Front StreetLisle, IL 60532 USAphone: 630-852-1699fax: 630-852-3678www.edmzap.com

—> Purchase or Repair:

#Elox Corporation by Michael Hendrick on 2005-09-12 15:53

Hell I was left a EDN ELOX HRP 64 and I would like to get some info on this machine. I dont even know if it works. If there is somewhere I could uptain or even better down load a manual I would be so much in your dept. Thanks Michael Hendrick

—> Purchase or Repair:

#Elox Corporation by Ernesto Rangel on 2012-04-16 18:14

I need help with a machine model Serial M-3 W/DA-000024 BMNO V05.256.9 and required support, are you have contact in Mexico an dis possible send me phone Thanks

—> Purchase or Repair:

#Elox Corporation by Jose Aubeyzon on 2011-09-30 19:11

We bought an EDM ELOX-AMERITRON here in PERU and planned to start working with it, but at the moment we pressed \"ON\" to start it, the sceen shows \"insert disk\" and doesn´t work.We would appreciate if you could advice us on how to fix this problem, if need, we would be willing to buy the programm…Purchase or Repair:

#Elox Corporation by Becky on 2012-05-01 02:27

I\'m trying to find a manual for an Agie Futura II Mondo I.

—> Purchase or Repair:

#Elox Corporation by Jose Aubeyzon on 2011-10-05 18:05

We bought an EDM ELOX-AMERITRON here in PERU and planned to start working with it, but at the moment we pressed \"ON\" to start it, the sceen shows \"insert disk\" and doesn´t work.We would appreciate if you could advice us on how to fix this problem, if need, we would be willing to buy the programm…Purchase or Repair:

#Elox Corporation by angel laclaustra on 2006-02-10 20:00

HelloI have a 1990 edm fantastic elox cnc with a Fanuc contoller. Eloxtype 3-2012 cncSeerial: 004300ControlType: sys 11 cef 100serial: 89-1573Im having the following erros:EX002 Servo motor over TempOT008 z - over travel (hard)Also i have a cable disconected that i dont know where goes. The cable nu…Purchase or Repair:

#Elox Corporation by Daniel Espinosa on 2010-12-20 18:54

We have a EDM Elox 400 D that when it is pressed the start button the electrodes comeback to home position. Our maintenance crew tried to fix up without success. I wonder if you have a service Engineer that could help us to fix it up.Best Regards(Turbotec is located just 20 minutes from San Diego Ca…Purchase or Repair:

#Elox Corporation by michael lewis on 2009-10-05 12:19

We have an Elox edm hrp 64 and i am looking for a manual, filters and DTE 25 oil for it. Any help would be greatly appriciated.Thank youMike

—> Purchase or Repair:

#Elox Corporation by SERGIO AYLLON TREJO on 2010-01-26 22:09

disculpen pero no ablo ingles solo spañol me urge el diagrama de una erocionadora elox t50s urge

—> Purchase or Repair:

#Elox Corporation by Don K on 2006-01-19 16:28

We also own a Elox HRP-64 machine. We also are missing the manual and would like to know it you found one and would like to sell us a copy or tell us where you got it so maybe we could also purchase one.Thanks Don Ketz

—> Purchase or Repair:

#Elox Corporation by Rodrigo Avendaño on 2006-05-29 02:54

My friend , I could not write before, so that they robbed my to me notebock and it did not find your e mail I feel it. I have been needing to know how you can help me for many months that I cannot make take my machine, here in Chile are technicians no to be able to repair to my machine ELOX heritage…Purchase or Repair:

#Elox Corporation by michael spacco on 2006-07-18 19:02

ram will not go up switches work. we had to move it and since then the ram dropped and will not go up. Is it the hydrolics and how do i bleed the air out.

—> Purchase or Repair:

#Elox Corporation by sergio garcia on 2012-06-14 17:28

I have a edm elox workmaster 45 whit futura 50 control,but when I buy the machine it came whit some disconnected wires inside the controls and I have not any kind of electrical wiring diagram or any manual for this machine,I wold like to get that manual books, please send me quotation for all manual…Purchase or Repair:

#Elox Corporation by Fabiola Alvarez on 2007-08-29 04:14

We own a Elox HRP-64 machine and we are missing the manual and would like to know it you found one and would like to sell us a copy or tell us where you got it so maybe we could also purchase one.

—> Purchase or Repair:

#Elox Corporation by Caleb Walker on 2009-12-16 00:54

Hello,We had a bit of a meltdown which damaged the Elox Workmaster 45 jog switch panel. The switches & wires are so fried they are almost un-traceable. Anyway I though you may be able to point me in the direction of a jog switch panel pinout diagram?Best regards,Caleb Walker

—> Purchase or Repair:

#Elox Corporation by Wayne Lacouture on 2015-04-01 20:34

I am looking for a electrical diagram for my ELOX machine it is a SYS-11 CEF50 I am mainly concerned about the power cables to the cutting head the complete power circuit.Thank you,Wayne LaCouture

—> Purchase or Repair:

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.