Komax for Service call 1-336-969-0110 at Industrial Electronics Repair

Komax Service & Repair Forum

Hello,I am reaching out on behalf of a client who is experiencing issues with their Komax 33 wire machine. The part number involved is . The client has described a problem with the machine, but I do not have all the details at the moment. Could you please provide me with some guidance on how we can address this issue?Thank you for your assistance.Best regards,

— Posted by Dian Smith on 2013-07-10

Reply🗨️Ask a New Question Below❓

If you need your Komax unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 17 Comments

#Komax by Roger Holt on 2007-07-17 18:07

I would like to get an estimate on fine tuning and calibrating our Komax 33.

#Komax by Adan Caldera on 2008-05-05 19:41

Hi I have a 3 electronic board model IP1000 for Komax equipment can you help me to repair these electronic board the problem that this have are that the Crimpper don\'t work don\'t send the voltaje at the motor.Thanks for yopur help a have a nice day.

#Komax by victor vargas on 2008-06-28 07:14

Hello, I need repair service for some differents electronic equippment, example, MCI 711 press board, DAC-100 Servo control, BIO KARD, SOCCAPEL, POWER SUPPLY. Do you have some prices for the repair of this items? Thanks you/

#Komax by victor vargas on 2008-07-08 20:02

Hello, I need repair service o sell for some differents electronic equippment, example, MCI 711 press board, DAC-100 Servo control, BIO KARD, SOCCAPEL, POWER SUPPLY. Do you have some prices for the repair of this items? Thanks you/

#Komax by victor vargas on 2008-07-08 20:02

Hello, I need repair service o sell for some differents electronic equippment, example, MCI 711 press board, DAC-100 Servo control, BIO KARD, SOCCAPEL, POWER SUPPLY. Do you have some prices for the repair of this items? Thanks you/

#Komax by Juan G. Hernandez on 2008-10-25 16:33

we have a komax 33 that is not working properly. can you tell me how long will take you to do an evaulation?or how long am I looking to be with out the machine?Please let me knowJuan

#Komax by Bruce Real on 2010-03-18 03:44

looking for operation manual for a Komax 33.

#Komax by FERNANDO ADAME on 2010-08-20 23:30

HI. GOOD DAY I NEED REPAIR ONE E -CAD FROM MCI 761 I LIKE TO KNOW WHERE FOUND PIECES END IF YOU HAVE THE ELECTRONIC DIAGRAM OF THE CONTROL ..THANKS

#Komax by sergio venzor on 2011-01-26 18:46

Hello, I have a BT711 crimp module, the ip1000 board have a system failure 4, do you know which component is damage? thanks

#Komax by Massimiliano Brocchi on 2011-05-13 07:15

Dear Sirs,I\'d need a service manual for our machine KOMAX33 (S/N K0 4657) due to a strange error message about knife that we are not able to identify.Many thnaks in advance,Massimiliano BrocchiPlant mgr of ICAR SPAVia Nosea, 124030 Villa d\'Adda (BG)ITALYMob. +39 3290571734

#Komax by Luis Raul Godinez on 2012-08-15 16:34

repair cost ip1000and i need used qty.3

#Komax by Mary E. Perillo on 2012-08-15 22:11

Need a repair on an old Komax machine.

#Komax by Tom Stude on 2013-05-07 13:27

We have recently purchased a Komax 33. Upon power up the display comes on and we are able to change the length, size and number of pieces....etc., though the Start button LED does not come on. The emergency switch and button works. I noticed in the back a number of ports/connectors. Does this need a...
Show More

#Komax by Dian Smith on 2013-07-10 00:00

Hello,I am reaching out on behalf of a client who is experiencing issues with their Komax 33 wire machine. The part number involved is . The client has described a problem with the machine, but I do not have all the details at the moment. Could you please provide me with some guidance on how we can ...
Show More

#Komax by James Thompson on 2013-10-31 12:12

I need a copy of the komax 33 manual.

#Komax by Foued Rihane on 2014-07-22 22:08

Hello Mr.I have a problem with the Komax IP 1000.The error message is : communication default.Can you tel me which componet is damage?Thanks.

#Komax by CHIKHA on 2016-11-19 17:55

I bought the Komax 33 i can turn it on but i don't understand how it works, i want to get the manual so i can use it.

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.