Powcon Service & Repair Forum

Have not used welder in 30 years worked great thenI tried to use it and it would not weldthe wire feed works okthe only think different I do not have I don\'t have the co2bottle attached question is there a switch connected to the co2 that is keeping it from weldingCould use a little hekpThanksTIM

—> Purchase or Repair:

Reply🗨️Ask a New Question Below❓

• Powcon → Powcon BD103025 ↗
• Powcon → Powcon powcon 200 sm ↗
• Powcon → Powcon 200 SM Manual ↗
• Powcon → Parts of repair one welder POWCON 200 SM ↗
• Powcon → Powcon powcon 300st ↗
• Powcon → powcon 200 ↗
• Powcon → Powcon board ↗
• Powcon → Powcon PCB board problem ↗

Recent 10 Comments

#Powcon by Marino Octaviano Velastegui Gavilanes on 2009-08-26 20:42

Nosotros queremos reparar una máquina soldadora POWCON 200 SM.Necesitamos los siguientes repuestos.Cant # de denominación01 PC BOARD ASSY 105019 REV01 BUS 300v GMQ 3.2/1004 U.K. 919000-3 900202 900000-001ADEMÁS NECESITAMOS UN DIAGRAMA DE CIRCUITOS ELECTRICOS, que tenemos dificultades con su instalac…Purchase or Repair: ...Nosotros queremos reparar una máquina soldadora POWCON 200 SM.Necesitamos los siguientes repuestos.Cant # de denominación01 PC BOARD ASSY 105019 REV01 BUS 300v GMQ 3.2/1004 U.K. 919000-3 900202 900000-001ADEMÁS NECESITAMOS UN DIAGRAMA DE CIRCUITOS ELECTRICOS, que tenemos dificultades con su instalacíon.fUENTE DE PODER SERIE # 2M102302

—> Purchase or Repair:
Show More

➡️ Reply

#Powcon by Bryan Perry on 2008-09-06 19:41

I have a Powcon 200sm with wire feeder. The drive board went bad in the wire feeder, so I replaced it. Now I do not have fire on the mig gun the inch and purge switch do work and when you pull the trigger it does feed wire and the gas solenoid also accuates. There is 28 volts at the connector in the…Purchase or Repair: ...I have a Powcon 200sm with wire feeder. The drive board went bad in the wire feeder, so I replaced it. Now I do not have fire on the mig gun the inch and purge switch do work and when you pull the trigger it does feed wire and the gas solenoid also accuates. There is 28 volts at the connector in the back of the power supply I believe on pins 1 and 2. I tried to jumper pins 3 and 4 but could not hear the contactor. Upon opening the power supply and visually looking at the PCB board it appears to have been hot. Would you please email the procedure for troubleshooting the contactor set through the pin connector on the power supply. Thank You

—> Purchase or Repair:
Show More

➡️ Reply

#Powcon by Tim Murphy on 2014-03-07 22:18

Have not used welder in 30 years worked great thenI tried to use it and it would not weldthe wire feed works okthe only think different I do not have I don\'t have the co2bottle attached question is there a switch connected to the co2 that is keeping it from weldingCould use a little hekpThanksTIM—>…Purchase or Repair: ...Have not used welder in 30 years worked great thenI tried to use it and it would not weldthe wire feed works okthe only think different I do not have I don\'t have the co2bottle attached question is there a switch connected to the co2 that is keeping it from weldingCould use a little hekpThanksTIM

—> Purchase or Repair:
Show More

➡️ Reply