Rittenhouse Service & Repair Forum

I would like to install my RC633 which I removed from my old house. Can you send me instructions? Thank you.

—> Purchase or Repair: Ticket Image

— Posted by Theresa Perkins on 2008-12-16

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by Eric Hoffman on 2007-12-23 04:40
I have just recently purchased a house that has a Rittenhouse Model 7300 Intercom system that does not work. I am trying to find a schematic for it. I know that it is an old system, but would like to use it to monitor my young children. Any help would be appreciated.Thank you.Eric Hoffman—> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by joe Delle Dinne on 2011-12-20 00:25
I would like to know if spare components are still available? eg transistors and LM283T 5 pin audio amp or regulator? Or is there a replacement UNIT and what is the cost for a compatible unit.

—> Purchase or Repair:
#Rittenhouse by william hogan on 2006-09-05 18:05
I have a rittenhouse am radio intercome that works well. It has 7 receivers + the base unit. can it be changed to fm ? I believe it is a late 60s mdel. thanks

—> Purchase or Repair:
#Rittenhouse by A.L. Richard on 2010-08-09 13:32
My home was built in 1965 with the same Rittenhouse intercom/radio system that doesn\'t work anymore. I would like to upggrade with intercom/radio/ satellite radio system can you do the work? What would be the estimated cost?

—> Purchase or Repair:
#Rittenhouse by Debbie Solovey on 2014-10-25 01:56
Hello, I am living in the house I grew up in and all of a sudden I noticed thatthe front doorbell was not working. The side doorbell hasn\'t worked for a long time. I have done some research so I will give you the information I have.Nutone Chime Signal, made in USA 1952, Model K 26 902 or 002It is a…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Angela on 2015-11-22 00:03
i am looking for the cover of the door chime for the above model that needs replacing.

—> Purchase or Repair:
#Rittenhouse by rosemary ortiz on 2009-11-11 22:30
we can not get it to chime in sequence. if doorbell is pressed it chimes once (#4).

—> Purchase or Repair:
#Rittenhouse by sheila on 2011-09-05 18:24
Would you know where i can find a C8931R?

—> Purchase or Repair:
#Rittenhouse by macgretz on 2017-04-19 20:58
I have a Rittenhouse Emerson Elec Model C8326 (perhaps 1960's) that has stopped working today. The chimes and housing seem okay, but the mechanism and bell button are old and worn out. Do you have replacement parts - and at what cost?

—> Purchase or Repair:
#Rittenhouse by Eddie Rodriguez on 2019-10-13 21:47
I have a Master Model 631 & 632, The clock stop working. its showing the red dot on the face of the clock that indicates power failure. The chimes still work fine with no issue. Can you provide instruction on how to test and/or repair. Thank youEddie

—> Purchase or Repair:
#Rittenhouse by Tom Mitchell on 2005-11-30 17:54
I have a Rittenhouse Home Intercom, Model No. M7010 that had no audio. A technician said the amplifier was bad and he replaced several transistors in it, but the volume is very weak. He does not know exactly what transistors to use to replace the old ones, and does not have a schematic. Can you prov…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

—> Purchase or Repair:
#Rittenhouse by v on 2007-06-19 19:52
my dilemma also. have you found a suitable replacement? thanks.

—> Purchase or Repair:
#Rittenhouse by william j paveletz on 2018-03-09 19:10
i need a part model c8633 volts 16 need the main eletric gear

—> Purchase or Repair:
#Rittenhouse by Jim Drouillard on 2008-05-16 02:50
I have the above mentioned door chime (Rittenhouse door chime model C8536) that does not work correctly. There where some broken wires from the transformer coils that I soldered back on and now it does not work correctly. Do you have a schematic for this unit?

—> Purchase or Repair:
#Rittenhouse by Corinne Censulla on 2012-02-29 17:56
I have a very old doorbell/ clock combination. The Model # is 450. The chimes work but not the clock. Since it is installed into the wall is there one the will replace using the same insert?

—> Purchase or Repair:
#Rittenhouse by joe matthews on 2015-05-13 16:20
Unit was installed late 1960\'s. Need speakers, knobs and covers to upgrade system.

—> Purchase or Repair:
#Rittenhouse by Deborah Braid on 2009-12-14 16:48
I have an old rittenhouse 7021 (I think) it is from 1978. It needs a new from cover and the dial to change the stations doesn\'t work. Otherwise it works. Can it be fixed and about how much?

—> Purchase or Repair:
#Rittenhouse by isagani l. cua on 2015-03-13 18:40
Sir: Please help me diagnose the problem of my C8204 door chime, andthis morning I heard a noisy sound from the unit. And please give menearest service center here in Chino hills, CalifornialThanks

—> Purchase or Repair:
#Rittenhouse by Lynn Villano on 2011-05-06 13:29
but want door bell to continue working. Can we get wiring schematics?

—> Purchase or Repair:
#Rittenhouse by jim Snyder on 2012-01-12 05:28
A friend of mine has a doorbell that i am hoping to repair and would like to find the wiring diagram for it if possible. The only tag I can find on it saysArtolier Lighting & Sound Div. Emerson Electric Co. Rittenhouse Operations Honeoye Falls NY 14472 Model RC203 or RC208 Volt 10 There are three te…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Steve on 2011-05-01 18:27
need diagram for wiring of C8203. Only two reds, 2 whites, where would transformer lead be?

—> Purchase or Repair:
#Rittenhouse by pyle on 2015-07-10 18:32
Hey, the Rittenhouse C8578-1 135-7351-01 door chime went out mid-shift. Please check it out first thing in the morning. Thanks!

—> Purchase or Repair:
#Rittenhouse by David Bergeron on 2017-10-23 07:12
wonder if I can acquire 1of the 3 boxes that throws the donger to. ring the far right chime of 3

—> Purchase or Repair:
#Rittenhouse by Howard Hendricks on 2009-07-12 04:29
I have a Rittenhouse Chine door bell with four long poles. The model number is c8578-1, The unit will not work, I noticed two bad diodes, and removed them I am having problems locating the right ones. Is this something you can fix?

—> Purchase or Repair:
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

—> Purchase or Repair:
#Rittenhouse by Glenn Loiselle on 2012-08-09 11:58
I have a circa 1977 Artolier Lighting and Sound door Chimes / door bell / wall clock that HUMMS all the time. MODEL # C8633Can it be repaired?

—> Purchase or Repair:
#Rittenhouse by tom roegner on 2008-09-26 22:07
Eight chime unit {552} repeats sequence continually until switch is disconnected. Switch has been replaced but problem continues----any ideas and is it repairable.....

—> Purchase or Repair:
#Rittenhouse by karen varel on 2011-09-07 00:53
Do you sell parts for rittenhouse dooor chimes specifically Model #C8550 or do you know where I can get them?

—> Purchase or Repair:
#Rittenhouse by Barbara on 2006-08-27 17:45
This is an old system I would like to replace. Does the wire plugs have to be replaced. I would like sm=omthing that will be compatable with the wire plugs. Do you have any suggestionsThank You

—> Purchase or Repair:
#Rittenhouse by sue wardy on 2010-02-22 15:07
static, fade in and out radio. intercom doesn\'t work but don\'t care about that just want the fm on radio to work more consistently

—> Purchase or Repair:
#Rittenhouse by k. chang on 2009-06-17 02:34
how do we get this old door chime to work again?we\'re already replacing the batteries, what else should we do?thanks

—> Purchase or Repair:
#Rittenhouse by Robert King on 2010-08-02 01:52
I know this chime assembly is very old but is there a replacement kit for the hammers. they are sticking and perhaps the springs are just too soft. I\'d appreciate any help you can give me.

—> Purchase or Repair:
#Rittenhouse by Clay Johnson on 2015-03-08 20:13
Please provide information or assistance regarding Rittenhouse part number C8578-1 135-7351-01, described as a door chime. Thank you.

—> Purchase or Repair:
#Rittenhouse by van Aree on 2009-02-26 20:19
I am looking for a copy of Rittenhouse rm5 house intercom owner\'s manual.

—> Purchase or Repair:
#Rittenhouse by Fred on 2011-05-25 04:18
Art - did you get a reply in answer to your post?I am about to restore the same door chime, you may have info that can help.ThanksFred...

—> Purchase or Repair:
#Rittenhouse by neil Berman on 2009-07-08 05:25
I have a Rittenhouse Model S7806 Smoke/Fire detector system in my 3-level condo. It was there when I moved in so there is no manual for it.My problem is, after a thunder and lightening storm the other day, I came home to find all 3 units ringing. The only way I could silence them was to switch off t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Don Heeter on 2017-01-17 21:38
Dear Sirs, I have a Model RM-2.It was put in when the house was built in 1966.It does not work.Thank you for your help.

—> Purchase or Repair:
#Rittenhouse by Jim Fields on 2012-11-19 16:03
I have a schematic for Models M7010, M7011, M7012, M7020. The document also has AM Alignment, FM Alignment, Troubleshooting chart, and list of replacement parts for printed circuit board.

—> Purchase or Repair:
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Emily Gladden on 2016-10-16 21:20
When you press our door bell button a chime is not coming out of the box in the outlet.

—> Purchase or Repair:
#Rittenhouse by Pamela Brawdy on 2008-08-19 20:43
My sister inlaw gave me this doorbell clock, I do not have the chimes the model number is RC6333. Can you help.

—> Purchase or Repair:
#Rittenhouse by TR on 2007-10-27 18:13
I have a Rittenhouse intercom system that was installed in the 60\'s that worked fine until recently. Everything still works fine except the main intercom/control unit. Is there a replacement unit I can buy that I can use with all my existing speakers, etc throughout the house? Even a unit that only…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Franklin D Bamsey on 2011-08-30 18:30
I have an Emerson Door Bell C 8204 and it is not working. Need a response to this E- mail please.

—> Purchase or Repair:
#Rittenhouse by Brandon on 2010-01-02 05:17
Please contact me about the cover of the door chime Model c8204.We lost it during repainting the wall when we moved in 2 years ago.ThanksBrandon

—> Purchase or Repair:
#Rittenhouse by jason surrette on 2008-05-21 22:34
Don\'t know what\'s wrong with the unit. Do ya\'ll know what the input voltage is supposed to be? The back of the unit says only use a \"no. 35 transformer\".

—> Purchase or Repair:
#Rittenhouse by LINDA BURGESS on 2017-03-30 17:16
Have model C 8203, 10 volt door bell. Am missing the push button remote that fastens to wall outside the front door. Any suggestions?

—> Purchase or Repair:
#Rittenhouse by DominicJ. Carini on 2009-07-23 03:03
I have a 30 year old rittenhouse door chime with the 4 sequential chimes, one of the plungers has gone lazy. I took the transformer out to try to clean it and lost the little spring that gives the plunger resistance . Do you have any ideas ?Or do you sell parts, perhaps a whole tansformer. I tried t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jay Sturm on 2007-02-24 18:35
Dear Sir: I\'m looking for a electric schamitic for an Emerson Rittenhouse intercom Model rm20/rm22. Any help in this matter would be appropriated. Thank You, JAY

—> Purchase or Repair:
#Rittenhouse by Gord Sweatman on 2017-09-01 21:46
Removed outer casing - now doorbell doesn't work - noticed loose redwire - where do I attach?

—> Purchase or Repair:

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.