Troubleshooting Rittenhouse: Common problems and repair info

Rittenhouse for Service call 1-336-969-0110 at Industrial Electronics Repair

Rittenhouse Service & Repair Forum

My Rittenhouse door chime\'s top plunger does not work, the previous homeowner said when he was hooking it up, by accident the top soleniod was getting power all the time and over heated and it has not worked right since... can this be fixed ????

—> Purchase or Repair:

— Posted by Jim Romeiser on 2011-08-18

Reply🗨️Ask a New Question Below❓

Recent 312 Comments

#Rittenhouse by Shigong Yang on 2008-08-27 03:12

The system is old and has not worked when I bought this house. Wish can fine some one to fixe and test it.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by David Hocevar on 2011-12-05 17:56

I have a ritenhouse emerson door chime unit. It just started chimeing for no reason I had to disconnect it to silence it. Now when I hooked it back up nothing happens. Clock doesn\'t work, chimes don\'t work.Model 086331 4 tubed chime It also has a teledcrome syncronis motor. Any hope for it.Thank Y…Purchase or Repair:

➡️ Reply

#Rittenhouse by DANNY on 2010-05-06 16:48

I AM A ELECTRICAL CONTRACTOR AND HAVE BEEN TOLD THAT NUTONE WILL WORK USING EXISTING WIRING THE PROBLEM IS NUTONE WILL NOT WARRANTY IF YOU DO NOT USE NUTONE WIRE, BUT THEY DO HAVE A 30 DAY RETURN POLICY TRY THE SYSTEM IF IT DOES NOT WORK TAKE IT BACK ASAP

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Barbara on 2006-08-27 17:45

This is an old system I would like to replace. Does the wire plugs have to be replaced. I would like sm=omthing that will be compatable with the wire plugs. Do you have any suggestionsThank You

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Jeff Swiger on 2009-12-09 21:38

I would like to replace my working existing RMC-4 rittenhouse intercom with a compatible unit. While using the existing wires? Suggestions _ and would you be interested in the old unit and speakers - 8 + 1 doorThanks,

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by David on 2018-03-04 18:16

Have you ever heard of a response on the Rittenhouse 631/632. I too am refurbishing one and need to know the correct tranformer voltage needed and a wiring diagram surely would help. Any insight?

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by bill morrison on 2006-05-03 03:40

we have an old rittenhouse intercom system. the units look old but still works fairly well. need information on how to update system look without replacing entire system. we\'re remodeling in some areas and would like to check out updating units. don\'t have specs on the system. not sure of—> …Purchase or Repair:

➡️ Reply

#Rittenhouse by dan mazzola on 2017-02-17 16:32

need a sequence timer for a emerson rittenhouse model # 632 631

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Mark on 2017-09-04 20:48

I'm looking for a replacement circuit board for a Rittenhouse model C8538. Please let me know where I can purchase one.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Eddie Ellis, Jr. on 2012-04-02 22:38

I have a Rittenhouse / Emerson intercom system with individual stations for each room. Two of the intercom speakers nolonger work. When I opened them they have one red, one yellow and one black wire leading from the unit. Is it possible to get them worked on or replaced. They measure 8 3/4\" long X …Purchase or Repair:

➡️ Reply

#Rittenhouse by John Erlinger on 2011-12-01 21:30

It appears the hammers are sticking or a spring has broken. There are three. Can i get replacement solenoids/hammers, or an estimate to repair the whole Chime unit. Also if you think it would be best to buy new.Thank you.,John

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Theresa Perkins on 2008-12-16 16:21

I would like to install my RC633 which I removed from my old house. Can you send me instructions? Thank you.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Hal Hester on 2016-07-09 23:01

Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Ray Smith on 2011-11-29 00:44

very low sound no door chime

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by DARLENE on 2009-02-09 03:51

it will not turn off a red light stays on. do i need to replace or repair it.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Barb C on 2009-03-27 12:35

Same as James Mann note - have 1970\'s Rittenhouse intercom---can we replace old system - can we purchase new units but use same wiring??

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Richard Burnham on 2021-03-28 21:10

Front and back door bells. I need a diagram showing how to connect the wires from the doorbells. Front works with one wire from Front doorbell going to Terminal B and the other going to Front in the 16 VAC group. I assumed one wire would go from Back doorbell to Terminal A and the other to Back in t…Purchase or Repair:

➡️ Reply

#Rittenhouse by Bob Hilsher on 2010-03-27 16:29

Unit stopped working. Have 16+ volts coming to it but no sound. Assume the syncronous motor is out... Telechron model M3151, Type H18, 3.6 rpm, 60 cy, 16 v. Is the replacement motor available? Price?Could it be anything else? All wiring is in tact on board.Thanks, Bob

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Franklin D Bamsey on 2011-08-30 18:30

I have an Emerson Door Bell C 8204 and it is not working. Need a response to this E- mail please.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Ejschreier@hotmail.com on 2015-03-25 11:15

Lost during remodeling.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by martin stacy on 2015-11-30 23:17

Hi, I just moved into house with Artolier Musician M7011 by Rittenhouse which doesn\'t work. I know you don\'t know why it doesn\'t work but any ballpark guesses at repair cost if I ship it to you? My zip is 516539 thx

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Hal Hester on 2016-07-09 23:01

➡️ Reply

#Rittenhouse by Anthony Butts on 2011-10-02 19:14

The unit works, but possibly in need of some service. The AM radio works , but no FM. There is a bit of background noise in the system.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Richard Baer on 2012-03-06 23:58

This unit puts out a chirping sound (Similar to sound of a smoke alarm) on a continuous basis, one chirp about every 30 seconds. Please advise what I should do, short of disconnecting the unit, to stop this annoying sound.Thank you,Richard Baer

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Paul Winchock on 2018-10-15 21:41

I have a Rittenhouse 550, 551 doorbell chime.The unit itself works fine. What I am missing (which someone was supposed to nor trash) is the transformer that sequences the chimes. Do you have a transformer for this that will work? And if so, obviously, what would one cost?Thank you for taking the tim…Purchase or Repair:

➡️ Reply

#Rittenhouse by Tom Gleason on 2011-03-31 01:27

Looking for a sequencer box for a model 552 doorbell chime. I know they are rare. Does somebody make a retro fit or do you have a good used one. If none of the above then how about schemetics and I will get one made. Thanks-Tom

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Maryellen Boudria on 2009-07-19 19:15

I have a Rittenhouse chime Model #410 with it\'s companion two chime on second floor of our 1927 home. The door bell chime works however we are not getting all chimes to work. Only two tones downstairs. Can this be repaired? Please advise.Also, can you tell me how old this model of Rittenhouse is?Ma…Purchase or Repair:

➡️ Reply

#Rittenhouse by Bradley Lowe on 2015-12-05 21:41

HelloIt came with the house had a ele.and he had no luck with repair

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by John Medina on 2013-02-22 19:58

Ubit was working fine, decided to hook up old style HI-FI unit per instructions and started blowing fuses. Looks like I created a short! Can you give me an idea of cost to repair and shipping charges? Thanks, John Medina

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by dave walters on 2008-10-24 14:59

Just wondering i have a rittenhouse system rcm-1 and the intercom system part does not seem to be working. We can broadcast for the main unit and it is heard in the other units but when we try to broadcast from one of the other units to the main you can not hear the person ? Anysuggestions or do you…Purchase or Repair:

➡️ Reply

#Rittenhouse by Earl Miller on 2012-10-11 01:23

Is there a new updated unit (with new bells & whistles) that can use the existing wiring and wall recesses of the old units. If so, where can I get them and what would be a ballpark pricing? Thanks

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by vero cho on 2007-06-19 19:49

sheetrocking my house after it was flooded by katrina, the contractor stupidly threw away the master station to my doorbell/radio/intercom system which rendered the system inoperable. i have asked an electrician friend to look at it and he cannot find a suitable retrofit. we will have to replace the…Purchase or Repair:

➡️ Reply

#Rittenhouse by william j paveletz on 2018-03-09 19:10

i need a part model c8633 volts 16 need the main eletric gear

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by phil hartshorn on 2017-01-10 16:24

need wiring diagram for c8538r door chime

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Chuck Duncan on 2013-03-20 00:35

Was working well until I sanded and painted the kitchen. I took the chimes down to paint, put them back and nothing works. I get voltage coming in but it doesn\'t move anything.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Mickey Loveria on 2007-08-30 14:53

Existing model was put in my home maybe late 60\'s, with ivory base unit and 4 ivory receivers plus brass door unit intercom. The radio reception is irregular, fades in and out and there is much static. Sometimes have to jiggle knobs on base unit to tune radio! Any suggestions on where to go for upg…Purchase or Repair:

➡️ Reply

#Rittenhouse by Roshan on 2011-04-18 18:17

I have an old Rittenhouse intercome unit, since I don\'t use it that much, I would like to replace the face of it with something newer, don\'t know if it;s possiable? please let me know how i can do this.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Walter Powell on 2013-06-15 18:30

Front door button will only ring one time. Side door button will only ring one time. Want front door to ring two times (ding-dong). Don\'t see how to wire it right.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Qaiser Baig on 2012-07-01 04:25

Hi,Some one open the wires of my door bell Model C8550 (in the bell). Would you please give the wiring/connection diagram for this door bell so that I can re-connect the wire to operate my door bell.You co-operation & early response will be highly appreciated.Regards,Qaiser Baig—> …Purchase or Repair:

➡️ Reply

#Rittenhouse by Kathy Grant on 2018-09-24 16:43

I recently purchased an older home that has a Model # RC-475 - 16 volt door chime that works fine, but lacks the cover. Is it possible to purchase just a cover from you or is something like this no longer available. Amazon has one but the mfg. dimensions wouldn't fit. As close as I can measure …Purchase or Repair:

➡️ Reply

#Rittenhouse by Karen Noll on 2009-11-16 14:27

I am looking for a cover to Rittenhouse, model 912 (possibly 812, numbers are difficult to read). Can you help?

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Kathy on 2016-08-16 17:08

can i have this unit repaired and what do i need to do.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by DAVE ROSS on 2007-05-18 16:21

EVERYTHING WORKS FIND..JUST WANT TO UPDATE OLD UNIT

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Bob Przybylski on 2018-11-28 01:06

I have a Rittenhouse door bell model c8355 and the transformer (that is what I think it is) has failed & does nothing but hum. Can I get a new transformer? or can I buy a replacement at the local home depot or Lowes?

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Scott Poulos on 2009-05-23 13:59

I am looking for a replacement unit or one that is compatable and larger to cover existing hole. please respond even if you are not interested or cant get what I need so I can try elsewere.

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Ken Selinger on 2012-06-06 02:03

We have an older intercom system M9325 stations, M9318, and M9322. We are wondering if there is anything we can do to reduce the standing hum.Thanks

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Dick Dingman on 2009-04-20 19:15

I purchased this residential unit in 1986. It is now giving a significant hum and does not produce all of its chimes.Does this give you a clue as to repairability?

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by tony on 2011-08-16 17:00

where can i find rittenhouse intercom/radio part??

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Paul on 2016-09-11 18:49

Are you able to repair it?

—> Purchase or Repair:

➡️ Reply

#Rittenhouse by Steve on 2011-05-01 18:27

need diagram for wiring of C8203. Only two reds, 2 whites, where would transformer lead be?

—> Purchase or Repair:

➡️ Reply