Rittenhouse Service & Repair Forum

Hello, I purchased my 4 note-8 note melody door chime in 1995. It has been set up on a battery operation operation

—> Purchase or Repair: Ticket Image

— Posted by Marlene Ilijanich on 2024-06-26

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by Lori on 2008-12-29 00:49
Years ago lightening hit house the chime stoped working the unit is in the kitchen and of coarse the door bell at the front door to push with finger ..doesnt work anymore can this be fixed ??/

—> Purchase or Repair:
#Rittenhouse by Mark Hefner on 2013-03-03 02:30
i am looking to replace my intercom system and looking for a new system to replace it with.

—> Purchase or Repair:
#Rittenhouse by Tom Mitchell on 2005-11-30 17:54
I have a Rittenhouse Home Intercom, Model No. M7010 that had no audio. A technician said the amplifier was bad and he replaced several transistors in it, but the volume is very weak. He does not know exactly what transistors to use to replace the old ones, and does not have a schematic. Can you prov…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by GALLAGHER on 2025-04-27 13:41
Drive or board failure on Rittenhouse M7012 intercom/radio. Needs immediate attention to avoid disruption. Heading to next location now.

—> Purchase or Repair:
#Rittenhouse by Andrew Lazazzera on 2017-01-16 17:16
HAVE --MODEL DS-2 DOOR SENTRY SAYS 'NOT TO CONNECT TO POWER SOURCE OTHER THAN STANDARD 16 VOLT CHIME TRANSFORMER'NEED TESTING OF ITS TRANSFORMER.I THINK ITS THE TRANSFORMER!WHAT IS PROCESS TO FOLLOW FOR THIS?ANDREW h=773-589-0150 c=773-899-0423

—> Purchase or Repair:
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

—> Purchase or Repair:
#Rittenhouse by Billy Hubbard on 2011-01-02 16:44
The Rittenhouse door intercom answering system system was installed in 1978. It is not functioning well. Do you have a newer replacement for it that would still have the doorbell and intercom system? Does a new unit come with the exterior speaker?

—> Purchase or Repair:
#Rittenhouse by Don Meierhoff on 2013-01-01 10:50
Need a schematic for the Emerson-Rittenhouse Model rm20/rm22. Need to know transistor replacement numbers for the front end tuner.Thanks,Don

—> Purchase or Repair:
#Rittenhouse by LINDA BURGESS on 2017-03-30 17:16
Have model C 8203, 10 volt door bell. Am missing the push button remote that fastens to wall outside the front door. Any suggestions?

—> Purchase or Repair:
#Rittenhouse by william junker on 2010-03-20 16:08
I need a replacement part for this devise.

—> Purchase or Repair:
#Rittenhouse by Martin on 2009-02-08 05:30
I have the exact same problem, but it\'s not caused by a lighted doorbell. Without the doorbell connect (and not crossing the wires) the chime mechanism keeps repeating. I\'m not sure whether it\'s because the contacts aren\'t lined up correctly or whether it\'s a wiring problem. I\'ve tinkered and …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Michelle NEWBY on 2009-05-20 00:04
Wee have an Emerson Rittenhouse doorbell model #RC552-1. The motor has fried itself. Can you repair? Thank you. H - (805) 685-2317

—> Purchase or Repair:
#Rittenhouse by Larry Yudkowitz on 2020-05-13 00:16
I have Model 380 16V. I had connected it ot a Ring Video 2 Doorbell and it worked fine for several months. Now there is a loud humm coming from the chime. I think the Ring ihas a problem. Ring says the chime may not be compatible. Ring says the model 382 is compatible. Whould you know the difference…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Deborah Braid on 2009-12-14 16:48
I have an old rittenhouse 7021 (I think) it is from 1978. It needs a new from cover and the dial to change the stations doesn\'t work. Otherwise it works. Can it be fixed and about how much?

—> Purchase or Repair:
#Rittenhouse by randy connelly on 2010-04-12 00:59
I need a Rittenhouse door bell botton part number C8000. Is this womethign you may have?

—> Purchase or Repair:
#Rittenhouse by Emily Gladden on 2016-10-16 21:20
When you press our door bell button a chime is not coming out of the box in the outlet.

—> Purchase or Repair:
#Rittenhouse by Ray G. Brubaker on 2017-09-11 14:32
I have a model Rittenhouse # E780DC door bell push button. The center plastic button is broken. I need a replacement . I can use the whole assemblyPlease email me as to where I can buy it. Thank you.

—> Purchase or Repair:
#Rittenhouse by Ken Bentham on 2017-04-25 21:05
Bell is connected to two doors. The front door works fine. The rear door won't ring at all. Can't tell what might be disconnected. Any ideas would be a big help. Thanks.Ken Bentham

—> Purchase or Repair:
#Rittenhouse by Mark Ivess on 2011-08-01 00:00
Hey there, I've been tasked with looking into an issue with a Rittenhouse C8578-1 135-7351-01 door chime. I don't usually work on hardware like this, so I could really use some guidance on how to fix or replace it. Any help or advice you can provide would be greatly appreciated. Thanks in advance!—>…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Donald Brown on 2017-07-07 23:15
I need to have a bulb replacement performed on a 1980ties vintage bronze doorbell. The spring works fine but light nolonger stays on.Regards, Don

—> Purchase or Repair:
#Rittenhouse by Kenneth Jackson on 2009-06-25 01:00
I have had this for almost 50 years and the clock does not work, for some unknown reason, and the chimes are weak sounding and miss at times. I need help. Can this be repaired?

—> Purchase or Repair:
#Rittenhouse by DeLane Smith on 2008-09-16 13:35
I need a address to send this unit to get it repaired

—> Purchase or Repair:
#Rittenhouse by Adrian Younger on 2008-07-08 00:43
Hello. I have an Emerson-Rittenhouse Door Chime Model RC577 and it has quit working. I was wondering if there is a replacement transmitter available for this chime. It has the motor attached to the transmitter so I don\'t htink I can get a replacement at a store. Any information you could give me wo…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Delia Castillo on 2008-07-29 03:14
we bought this house with installed system. not working. power source not found.

—> Purchase or Repair:
#Rittenhouse by Earl Miller on 2012-10-11 01:23
Is there a new updated unit (with new bells & whistles) that can use the existing wiring and wall recesses of the old units. If so, where can I get them and what would be a ballpark pricing? Thanks

—> Purchase or Repair:
#Rittenhouse by Jim on 2010-05-01 22:41
I have the above model doorbell and really like the sound vs. the new \"electronic sound\" doorbells. Problem is the mechanism inside the doorbell (the part with the two knockers that the wires attach that hit the bells to make the sound) no longer works. Can I still get this part replaced and if so…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by tom roegner on 2008-09-26 22:07
Eight chime unit {552} repeats sequence continually until switch is disconnected. Switch has been replaced but problem continues----any ideas and is it repairable.....

—> Purchase or Repair:
#Rittenhouse by Dorothy \"Ann\" Imhoff on 2014-10-23 22:17
A Rittenhouse model 312 came with my home. It works but the chimes are not loud enough to heard unless you are in the room where the doorbell is mounted.I would hate to replace it because other than this it is very workable.

—> Purchase or Repair:
#Rittenhouse by Yale Wolff on 2011-03-15 15:01
Have a Rittenhouse intercom system installed in 1956. There appears to be a dead short in the Master.Is there a NuTone Master AM/FM which will work with the satellite room units?

—> Purchase or Repair:
#Rittenhouse by bill whitacre on 2013-11-16 18:30
need to reconnect wires to front, rear & trans positions.

—> Purchase or Repair:
#Rittenhouse by David Strodel on 2010-12-05 00:34
Hi, I have a Rittenhouse 330 Chime that is not working. Is there a way to get a rough estimate of cost? It may be the transformer or the hammers as they are sticky.David

—> Purchase or Repair:
#Rittenhouse by e. jureller on 2024-12-01 00:00
Urgent Follow-Up Rittenhouse RM Intercom DownDear Team,I am following up on the previous message regarding the non-functional Rittenhouse RM intercom unit. It is imperative that we address this issue

—> Purchase or Repair:
#Rittenhouse by Morris Hoagland on 2014-01-05 03:53
My Rittenhouse Master unit has failed. Is there a replacement unit I can purchase?

—> Purchase or Repair:
#Rittenhouse by Diane P on 2019-05-22 14:20
I have a rittenhouse westminister door chime master model 631 and 632 that I removed from my family home when it was being sold. I have everything except the Rittenhouse no. 42 transformer, which is need before the electrician can install it in my home. Do you have this transformer or know where I c…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Theresa Perkins on 2008-12-16 16:21
I would like to install my RC633 which I removed from my old house. Can you send me instructions? Thank you.

—> Purchase or Repair:
#Rittenhouse by John Zeitler on 2012-12-05 22:32
I am looking for the cover that is a black plastic 8 3/8\" wide, 5 1/2\" high, and 2 1/8\" deep. Any idea where I can find a suitable replacement? Thanks.

—> Purchase or Repair:
#Rittenhouse by Dave Spieker on 2017-11-06 22:05
I am looking for a Rittenhouse Chime Receiver Model C8931R. Would you have one available for purchase or can you direct me to a person or another company that may have one available. Thank you!

—> Purchase or Repair:
#Rittenhouse by vero cho on 2007-06-19 19:49
sheetrocking my house after it was flooded by katrina, the contractor stupidly threw away the master station to my doorbell/radio/intercom system which rendered the system inoperable. i have asked an electrician friend to look at it and he cannot find a suitable retrofit. we will have to replace the…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by ellen wright on 2019-03-18 14:12
who repairs or work on the old Rittenhouse intercom systems.I would like to do an upgrade. Since I already have holes in the wall from the old Rittenhouse. I would like to upgrade to something along this same size.

—> Purchase or Repair:
#Rittenhouse by Jeffrey on 2008-11-22 22:27
This problem may be caused by a lighted doorbell. After the bell is wrung, the light will re-illuminate. When that happens it may be drawing just enough power to make the door chimes think that the button was pressed once again. This is a repeating pattern.If a lighted door button is used, the solut…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Donna Dodson on 2007-03-02 16:22
I would like to see if I can get this to work. But I don\'t know where to start.

—> Purchase or Repair:
#Rittenhouse by Anthony Butts on 2011-10-02 19:14
The unit works, but possibly in need of some service. The AM radio works , but no FM. There is a bit of background noise in the system.

—> Purchase or Repair:
#Rittenhouse by Tobie Ross on 2018-04-13 02:54
I have a Sears Solid State Am-FM Master Station Radio/Intercom Model 113.35150 built by Emerson Electric. Can you repair this station. Please advise/

—> Purchase or Repair:
#Rittenhouse by David Bergeron on 2017-10-23 07:12
wonder if I can acquire 1of the 3 boxes that throws the donger to. ring the far right chime of 3

—> Purchase or Repair:
#Rittenhouse by Jack Mc Sweeney on 2008-09-10 22:29
This is a two unit intercom and door opener for apartments. Presently, it has current but buzzes the door open without pushing the switch, and has no voice tones.

—> Purchase or Repair:
#Rittenhouse by Jeff Swiger on 2009-12-09 21:38
I would like to replace my working existing RMC-4 rittenhouse intercom with a compatible unit. While using the existing wires? Suggestions _ and would you be interested in the old unit and speakers - 8 + 1 doorThanks,

—> Purchase or Repair:
#Rittenhouse by scott grim on 2009-07-22 11:43
I\'ve recently come in the possesion of an emerson-rittenhouse model 633 door chime and clock. Somebody must have placed 120volts of power to the 16 volt circiut burning out all the electronics. I need all the electrical components including the hammars and motors. if anyone knows where i can get pa…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Steve on 2011-05-01 18:27
need diagram for wiring of C8203. Only two reds, 2 whites, where would transformer lead be?

—> Purchase or Repair:
#Rittenhouse by Ken Selinger on 2012-06-06 02:03
We have an older intercom system M9325 stations, M9318, and M9322. We are wondering if there is anything we can do to reduce the standing hum.Thanks

—> Purchase or Repair:
#Rittenhouse by Ron Abrams on 2009-02-18 02:03
I\'m working on a unit which has been in the family for years.Emerson- Rittenhouse RC 633, 16 voltOne of the solenoid/hammers don\'t work. Seems that the hammer is jammed in the tube. I\'d like to replace the solenoid. How may I order another one.Ron 305 803-5441

—> Purchase or Repair:

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.