Rittenhouse Service & Repair Forum

Ive had this unit in storage for years. Its not damaged at all. Its just been sitting unused. I would like to get it back in good shape and use it as our doorbell once again after all these years.

β€”> Purchase or Repair: Ticket Image

β€” Posted by Gregory Behr on 2026-07-21

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110


Recent 315 Comments

#Rittenhouse by Joe on 2012-04-18 13:36
Could you please direct me as to where I may be able to obtain a circuit diagram for a rittenhouse installed in the 1980?Many thanksJoe

β€”> Purchase or Repair:
#Rittenhouse by David Hocevar on 2011-12-05 17:56
I have a ritenhouse emerson door chime unit. It just started chimeing for no reason I had to disconnect it to silence it. Now when I hooked it back up nothing happens. Clock doesn\'t work, chimes don\'t work.Model 086331 4 tubed chime It also has a teledcrome syncronis motor. Any hope for it.Thank Y…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Franklin D Bamsey on 2011-08-30 18:30
I have an Emerson Door Bell C 8204 and it is not working. Need a response to this E- mail please.

β€”> Purchase or Repair:
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Clay Johnson on 2015-03-08 20:13
Please provide information or assistance regarding Rittenhouse part number C8578-1 135-7351-01, described as a door chime. Thank you.

β€”> Purchase or Repair:
#Rittenhouse by Kathy on 2016-08-16 17:08
can i have this unit repaired and what do i need to do.

β€”> Purchase or Repair:
#Rittenhouse by Jorge Crespo on 2015-05-11 04:05
Riitenhouse chime model C8538R to connect into the AC adapter 16 volt .

β€”> Purchase or Repair:
#Rittenhouse by Brent Stoll on 2014-01-07 03:22
Label states Emerson Model S7671Rittenhouse DivisionArtolier lighting & soundEmerson Electric CoHoneoye Falls, New York 14472Second Label statesFire Alarm DeviceSingle and/or Multiple stationHome built in early 70\'s and have not found any information per this model and/ or type of device. If you ha…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Emily Gladden on 2016-10-16 21:20
When you press our door bell button a chime is not coming out of the box in the outlet.

β€”> Purchase or Repair:
#Rittenhouse by Frank Spramelli on 2015-02-10 19:04
needs repaired tuning dial is broken.

β€”> Purchase or Repair:
#Rittenhouse by peter oliver on 2009-07-16 23:50
I am looking for a remote button for this system.Would possibly trade a receiver unit as I have extra.

β€”> Purchase or Repair:
#Rittenhouse by Janice Lopez on 2009-08-12 02:45
I AM LOOKING FOR A DOOR CHIME FOR MY BUSINESS THAT WHEN SOMEONE ENTERS THE FRONT DOOR THAT I WILL BE ABLE TO HEAR THE CHIME IN OTHER AREAS OF MY BUILDING AS WELL. I NEED SOMETHING THAT WILL HAVE A LOUD CHIME BECAUSE MY BUILDING HAS MACHINERY RUNNING ALL THE TIME. CAN YOU SEND ME SOME INFORMATION. TH…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by MARK WILSON on 2011-01-12 14:35
This is a Mechanical doorbell with Electronic Control Board. I need Someone to give me an estimate for repair or tell me where I can get parts for this device. Thanks, Mark Wilson

β€”> Purchase or Repair:
#Rittenhouse by James L Rockney on 2021-10-04 16:06
The small piston that strikes the chime does not return back to the original position. There is a spring on the piston. It seems like the piston should have a retainer of some sort on the end to hold the spring in place. Is there supposed to be a retainer on the end of the piston to keep the spring …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Eric Hoffman on 2007-12-23 04:40
I have just recently purchased a house that has a Rittenhouse Model 7300 Intercom system that does not work. I am trying to find a schematic for it. I know that it is an old system, but would like to use it to monitor my young children. Any help would be appreciated.Thank you.Eric Hoffmanβ€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by sonny sadler on 2011-11-21 16:12
i would like to have an updated model the one i have was installed in 1977 it makes noise, drifts off stations all controls are noisey and sound is garbled. can you tell me where to get help.

β€”> Purchase or Repair:
#Rittenhouse by vera price on 2009-07-29 12:53
I have a door bell Model C8229 that started to make a ringing sound. It looks as if the plates are vibrating.

β€”> Purchase or Repair:
#Rittenhouse by Morris Hoagland on 2014-01-05 03:53
My Rittenhouse Master unit has failed. Is there a replacement unit I can purchase?

β€”> Purchase or Repair:
#Rittenhouse by Jim Drouillard on 2008-05-16 02:50
I have the above mentioned door chime (Rittenhouse door chime model C8536) that does not work correctly. There where some broken wires from the transformer coils that I soldered back on and now it does not work correctly. Do you have a schematic for this unit?

β€”> Purchase or Repair:
#Rittenhouse by joe matthews on 2015-05-13 16:20
Unit was installed late 1960\'s. Need speakers, knobs and covers to upgrade system.

β€”> Purchase or Repair:
#Rittenhouse by colleen on 2010-03-10 04:32
i have a model 7035 that was removed from the wall to repair the wall. Now I need to reconnect - but don\'t know how the wires go together. Are there any instructions available?

β€”> Purchase or Repair:
#Rittenhouse by Lynn Villano on 2011-05-06 13:29
but want door bell to continue working. Can we get wiring schematics?

β€”> Purchase or Repair:
#Rittenhouse by Diane P on 2019-05-22 14:20
I have a rittenhouse westminister door chime master model 631 and 632 that I removed from my family home when it was being sold. I have everything except the Rittenhouse no. 42 transformer, which is need before the electrician can install it in my home. Do you have this transformer or know where I c…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by vero cho on 2007-06-19 19:49
sheetrocking my house after it was flooded by katrina, the contractor stupidly threw away the master station to my doorbell/radio/intercom system which rendered the system inoperable. i have asked an electrician friend to look at it and he cannot find a suitable retrofit. we will have to replace the…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Adrian Younger on 2008-07-08 00:43
Hello. I have an Emerson-Rittenhouse Door Chime Model RC577 and it has quit working. I was wondering if there is a replacement transmitter available for this chime. It has the motor attached to the transmitter so I don\'t htink I can get a replacement at a store. Any information you could give me wo…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by sheila on 2011-09-05 18:24
Would you know where i can find a C8931R?

β€”> Purchase or Repair:
#Rittenhouse by P. Markworth on 2014-01-17 18:45
Do you know of anyone in Central or East Central Ohio who can repair a Rittenhouse electric door chime? It has four, short brass tubes and chimes like The Westminister chimes. Thank you.

β€”> Purchase or Repair:
#Rittenhouse by Ken Selinger on 2012-06-06 02:03
We have an older intercom system M9325 stations, M9318, and M9322. We are wondering if there is anything we can do to reduce the standing hum.Thanks

β€”> Purchase or Repair:
#Rittenhouse by Marlene Ilijanich on 2024-06-26 02:50
Hello, I purchased my 4 note-8 note melody door chime in 1995. It has been set up on a battery operation operation

β€”> Purchase or Repair:
#Rittenhouse by DANNY on 2010-05-06 16:48
I AM A ELECTRICAL CONTRACTOR AND HAVE BEEN TOLD THAT NUTONE WILL WORK USING EXISTING WIRING THE PROBLEM IS NUTONE WILL NOT WARRANTY IF YOU DO NOT USE NUTONE WIRE, BUT THEY DO HAVE A 30 DAY RETURN POLICY TRY THE SYSTEM IF IT DOES NOT WORK TAKE IT BACK ASAP

β€”> Purchase or Repair:
#Rittenhouse by Bob Hilsher on 2010-03-27 16:29
Unit stopped working. Have 16+ volts coming to it but no sound. Assume the syncronous motor is out... Telechron model M3151, Type H18, 3.6 rpm, 60 cy, 16 v. Is the replacement motor available? Price?Could it be anything else? All wiring is in tact on board.Thanks, Bob

β€”> Purchase or Repair:
#Rittenhouse by Richard Greene on 2008-12-30 17:19
I own a late 60\'s Emerson Rittenhouse Model RC633 door bell Chime.The clock works fine but the door bell doesn\'t.I believe there is a problem with the motor.Can I have this unit repaired and approximately the cost?

β€”> Purchase or Repair:
#Rittenhouse by Chuck Duncan on 2013-03-20 00:35
Was working well until I sanded and painted the kitchen. I took the chimes down to paint, put them back and nothing works. I get voltage coming in but it doesn\'t move anything.

β€”> Purchase or Repair:
#Rittenhouse by Jack Mc Sweeney on 2008-09-10 22:29
This is a two unit intercom and door opener for apartments. Presently, it has current but buzzes the door open without pushing the switch, and has no voice tones.

β€”> Purchase or Repair:
#Rittenhouse by GALLAGHER on 2025-04-27 13:41
Drive or board failure on Rittenhouse M7012 intercom/radio. Needs immediate attention to avoid disruption. Heading to next location now.

β€”> Purchase or Repair:
#Rittenhouse by Charles Rose on 2009-12-22 23:34
Need base station repaired. Would purchase old

β€”> Purchase or Repair:
#Rittenhouse by Bil Hoag on 2015-11-11 17:58
Installed in 1987 when we built the house. Has begun sporadic multiple, single dings, all hours, day and night. I have replaced, back up battery and fuse in motor. Now makes a fairly loud buzzing sound also. Thoughts?

β€”> Purchase or Repair:
#Rittenhouse by vandewater on 2025-05-14 19:14
just a heads up that the Rittenhouse RM20/RM22 intercom with radio unit went down mid-shift. Can you please check it out and follow up during the day? Thanks!

β€”> Purchase or Repair:
#Rittenhouse by Steve on 2011-05-01 18:27
need diagram for wiring of C8203. Only two reds, 2 whites, where would transformer lead be?

β€”> Purchase or Repair:
#Rittenhouse by Paul on 2016-09-11 18:49
Are you able to repair it?

β€”> Purchase or Repair:
#Rittenhouse by Scott Steffens on 2015-09-15 22:03
I have a Artolier Lighting & Sound Div - Emerson Electric Co / Rittenhouse Operations Honeoye Falls, NY 14473 Model C8577 - 16 Volts. Do not know how to wire. It was working when it was taken from another home.This home is set up with one front door bell - ding dong doorbell on 1st floor and the Rit…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jeff Swiger on 2009-12-09 21:38
I would like to replace my working existing RMC-4 rittenhouse intercom with a compatible unit. While using the existing wires? Suggestions _ and would you be interested in the old unit and speakers - 8 + 1 doorThanks,

β€”> Purchase or Repair:
#Rittenhouse by martin stacy on 2015-11-30 23:17
Hi, I just moved into house with Artolier Musician M7011 by Rittenhouse which doesn\'t work. I know you don\'t know why it doesn\'t work but any ballpark guesses at repair cost if I ship it to you? My zip is 516539 thx

β€”> Purchase or Repair:
#Rittenhouse by Richard Burnham on 2021-03-28 21:10
Front and back door bells. I need a diagram showing how to connect the wires from the doorbells. Front works with one wire from Front doorbell going to Terminal B and the other going to Front in the 16 VAC group. I assumed one wire would go from Back doorbell to Terminal A and the other to Back in t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by John Medina on 2013-02-22 19:58
Ubit was working fine, decided to hook up old style HI-FI unit per instructions and started blowing fuses. Looks like I created a short! Can you give me an idea of cost to repair and shipping charges? Thanks, John Medina

β€”> Purchase or Repair:
#Rittenhouse by jim Snyder on 2012-01-12 05:28
A friend of mine has a doorbell that i am hoping to repair and would like to find the wiring diagram for it if possible. The only tag I can find on it saysArtolier Lighting & Sound Div. Emerson Electric Co. Rittenhouse Operations Honeoye Falls NY 14472 Model RC203 or RC208 Volt 10 There are three te…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Paul Gilbert on 2016-06-07 01:02
Need to replace existing bell system with new Paul gilbert

β€”> Purchase or Repair:
#Rittenhouse by Andrew Lazazzera on 2018-02-05 18:04
Have Model DS-2 Door Sentry w/ 16v. chime transformer -Rittenhouse #30 or = need local chicagoland technician to trouble-shoot the control box w/ its transformer.-believe transformer is problem.

β€”> Purchase or Repair:
#Rittenhouse by Fred on 2011-05-25 04:18
Art - did you get a reply in answer to your post?I am about to restore the same door chime, you may have info that can help.ThanksFred...

β€”> Purchase or Repair:
#Rittenhouse by Art on 2011-02-07 18:45
My dad just passed away and I\'m moving his Rittenhouse Westminster clock/chime from his place to mine before selling the house. I believe it is a model 631 or 632 but I\'m not sure - WHERE CAN I FIND THE MODEL NUMBER? (I\'ve seen pics of what appear to be identical units labeled 631/632).I\'ve got …Purchase or Repair: Ticket Image...
Show More

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.