Rittenhouse Service & Repair Forum

Hi,Some one open the wires of my door bell Model C8550 (in the bell). Would you please give the wiring/connection diagram for this door bell so that I can re-connect the wire to operate my door bell.You co-operation & early response will be highly appreciated.Regards,Qaiser Baig

β€”> Purchase or Repair: Ticket Image

β€” Posted by Qaiser Baig on 2012-07-01

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by sonny sadler on 2011-11-21 16:12
i would like to have an updated model the one i have was installed in 1977 it makes noise, drifts off stations all controls are noisey and sound is garbled. can you tell me where to get help.

β€”> Purchase or Repair:
#Rittenhouse by Marie Gunderman on 2007-11-26 01:41
We purchased our present home in 1998. It was custom built in 1983 with many upgrades that were available at that time. Unfortunately since we have lived here the system does not work. The main unit is 17\' wide and 9\" tall. There are 12 units scattered throughout the house. They each measure 7.5\"…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Debbie Solovey on 2014-10-25 01:56
Hello, I am living in the house I grew up in and all of a sudden I noticed thatthe front doorbell was not working. The side doorbell hasn\'t worked for a long time. I have done some research so I will give you the information I have.Nutone Chime Signal, made in USA 1952, Model K 26 902 or 002It is a…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by curtis gast on 2015-03-16 02:25
new home to me. system not working. any help would be great. thanks

β€”> Purchase or Repair:
#Rittenhouse by Mark Danko on 2015-09-10 19:17
Hi, need repair to this unit, sound cuts in and out when volume control knob is turned/wiggled. Moving molex 5 pin connector on circuit board also causes power to cut in and out. Mode delector knob has become stiff to operate. Please send estimate if repair is possible, thanks

β€”> Purchase or Repair:
#Rittenhouse by James A. Mann on 2008-06-26 12:40
We installed our Rittenhouse intercom system in 1978 when we built our new home. The speakers look out of date and would like a better main unit. We have 4 outside units, and 7 speakers.Can we purchase new units and still use the same wiring? Would appreciate a response ASAP. Thanks Jim MannP.S. Ple…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by roger crosby on 2009-06-22 18:11
I have renovated my house. I have a Model RC577 chime that is not working. I seem to have all the parts, 4 chimes, motor, etc.Please help me figure out how to repair.thank you

β€”> Purchase or Repair:
#Rittenhouse by Diane McCracken on 2010-10-26 15:22
Do you sell parts? I am looking for a replacement potentiometer for an Emerson-Rittenhouse RC 633. It is labeled Clarostat 140-6747/ 135-51.

β€”> Purchase or Repair:
#Rittenhouse by Kenneth Jackson on 2009-06-25 01:00
I have had this for almost 50 years and the clock does not work, for some unknown reason, and the chimes are weak sounding and miss at times. I need help. Can this be repaired?

β€”> Purchase or Repair:
#Rittenhouse by Pamela Brawdy on 2008-08-19 20:43
My sister inlaw gave me this doorbell clock, I do not have the chimes the model number is RC6333. Can you help.

β€”> Purchase or Repair:
#Rittenhouse by GENE LAYNE on 2016-07-28 12:11
Can you advise if a Emerson Rittenhouse RC 577 Doorbell mechanical chime will work with a 24V Transformer?I have a 16V and wanted to add a camera to this?ThanksGene 732-754-1205I cannot locate a manual im guessing this was made in the 70\'s

β€”> Purchase or Repair:
#Rittenhouse by tony on 2011-08-16 17:00
where can i find rittenhouse intercom/radio part??

β€”> Purchase or Repair:
#Rittenhouse by David Hocevar on 2011-12-05 17:56
I have a ritenhouse emerson door chime unit. It just started chimeing for no reason I had to disconnect it to silence it. Now when I hooked it back up nothing happens. Clock doesn\'t work, chimes don\'t work.Model 086331 4 tubed chime It also has a teledcrome syncronis motor. Any hope for it.Thank Y…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Tom Mitchell on 2005-11-30 17:54
I have a Rittenhouse Home Intercom, Model No. M7010 that had no audio. A technician said the amplifier was bad and he replaced several transistors in it, but the volume is very weak. He does not know exactly what transistors to use to replace the old ones, and does not have a schematic. Can you prov…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Barb C on 2009-03-27 12:35
Same as James Mann note - have 1970\'s Rittenhouse intercom---can we replace old system - can we purchase new units but use same wiring??

β€”> Purchase or Repair:
#Rittenhouse by dan mazzola on 2017-02-17 16:32
need a sequence timer for a emerson rittenhouse model # 632 631

β€”> Purchase or Repair:
#Rittenhouse by sal on 2018-01-16 16:43
Trying to obtain new springs and strikers/drivers

β€”> Purchase or Repair:
#Rittenhouse by charles dellasala on 2009-08-08 20:37
7th chime does not work can plunger be lubed if so with what

β€”> Purchase or Repair:
#Rittenhouse by Jeff Swiger on 2009-12-09 21:38
I would like to replace my working existing RMC-4 rittenhouse intercom with a compatible unit. While using the existing wires? Suggestions _ and would you be interested in the old unit and speakers - 8 + 1 doorThanks,

β€”> Purchase or Repair:
#Rittenhouse by jimmy jamison on 2008-04-08 19:34
we have modle m7035 the door bell and gate buzzer in still workes but the talk butten and volumne dose not. would like to fix or replace unitplease help thank you

β€”> Purchase or Repair:
#Rittenhouse by chris on 2015-08-27 21:30
I have gone through the trouble shooting I have 16 volts to the main unit just nothing coming out of main unit. like its acting as if there is no voltage. will not power up, no intercom, no radio is it replacement time or can this be repaired relatively cheap?

β€”> Purchase or Repair:
#Rittenhouse by vandewater on 2025-05-14 19:14
just a heads up that the Rittenhouse RM20/RM22 intercom with radio unit went down mid-shift. Can you please check it out and follow up during the day? Thanks!

β€”> Purchase or Repair:
#Rittenhouse by Jay Sturm on 2007-02-24 18:35
Dear Sir: I\'m looking for a electric schamitic for an Emerson Rittenhouse intercom Model rm20/rm22. Any help in this matter would be appropriated. Thank You, JAY

β€”> Purchase or Repair:
#Rittenhouse by craig cipriani on 2011-11-03 15:22
I hav a door chime and clock rittenhouse model 631 and 632 i need a wiring diagram for. any help i can get is appriciated thank you

β€”> Purchase or Repair:
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Ray G. Brubaker on 2017-09-11 14:32
I have a model Rittenhouse # E780DC door bell push button. The center plastic button is broken. I need a replacement . I can use the whole assemblyPlease email me as to where I can buy it. Thank you.

β€”> Purchase or Repair:
#Rittenhouse by Emily Gladden on 2016-10-16 21:20
When you press our door bell button a chime is not coming out of the box in the outlet.

β€”> Purchase or Repair:
#Rittenhouse by Linda La Bruna on 2011-10-16 18:45
I have a Ritten House RM-2 Radio Intercom in original box with original instruction booklet AND an OR-11 Outdoor Remote Station I am looking to sell.If you or someone you know would be interested, please contact me.

β€”> Purchase or Repair:
#Rittenhouse by Craig on 2018-12-27 00:39
I have a 620R, but your post was a long time ago. Did you get an answer?

β€”> Purchase or Repair:
#Rittenhouse by pyle on 2015-07-10 18:32
Hey, the Rittenhouse C8578-1 135-7351-01 door chime went out mid-shift. Please check it out first thing in the morning. Thanks!

β€”> Purchase or Repair:
#Rittenhouse by bill whitacre on 2013-11-16 18:30
need to reconnect wires to front, rear & trans positions.

β€”> Purchase or Repair:
#Rittenhouse by Bob on 2007-04-07 23:14
We have the same system in our home. Did you find any compatible system? Did you replace your system? If so, what system did you use? Thank you. We need to replace everything except the wiring.

β€”> Purchase or Repair:
#Rittenhouse by Mary Anne Fuscaldo on 2009-12-25 23:04
I moved this door chime/clock when it was working from one home to another. The electrician that hooked it up did not do it correctly and I have no schematic for how it should be wired. I know it needs three wires but not sure on which of the 7 screws they get wired to. They do not indicate Com or T…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Mike on 2025-06-05 15:12
Trying to hook up ring with the rittenhouse 531 model. Not sure how the wiring should be set up? 4 white and red wires with 0-4 posts?

β€”> Purchase or Repair:
#Rittenhouse by Chris Giebel on 2015-07-19 18:20
The Rittenhouse C8578-1 135-7351-01 is a door chime unit that is currently not working. That's the information I have so far.

β€”> Purchase or Repair:
#Rittenhouse by GUY DALFINO on 2013-01-24 17:30
I THINK I NEED A TRANSFORMER CLOCK WLL NOT RUN TX IN ADVANCE gUY

β€”> Purchase or Repair:
#Rittenhouse by John Erlinger on 2011-12-01 21:30
It appears the hammers are sticking or a spring has broken. There are three. Can i get replacement solenoids/hammers, or an estimate to repair the whole Chime unit. Also if you think it would be best to buy new.Thank you.,John

β€”> Purchase or Repair:
#Rittenhouse by Steve on 2011-05-01 18:27
need diagram for wiring of C8203. Only two reds, 2 whites, where would transformer lead be?

β€”> Purchase or Repair:
#Rittenhouse by Andrew Lazazzera on 2017-01-16 17:16
HAVE --MODEL DS-2 DOOR SENTRY SAYS 'NOT TO CONNECT TO POWER SOURCE OTHER THAN STANDARD 16 VOLT CHIME TRANSFORMER'NEED TESTING OF ITS TRANSFORMER.I THINK ITS THE TRANSFORMER!WHAT IS PROCESS TO FOLLOW FOR THIS?ANDREW h=773-589-0150 c=773-899-0423

β€”> Purchase or Repair:
#Rittenhouse by Shigong Yang on 2008-08-27 03:12
The system is old and has not worked when I bought this house. Wish can fine some one to fixe and test it.

β€”> Purchase or Repair:
#Rittenhouse by Wendy Morris on 2010-01-15 06:14
Our current cover is kind of an almond color. After remodeling our living room, all of the vents, outlets, etc. have been done in white. Would it be possible to purchase a white cover to replace the almond one for our door chime? What would the cost be?Please respond even if not available before I r…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by dominic Carini on 2009-07-28 00:55
Ihave about a 30 year old rittenhouse with 4 chimes.It seems that the solenoids that activate the strikers,are getting a little lazy.I have had one apart and try to clean it ,with not much succes,I even lost one of those tiny springs. I tried to replace it with a similar one ,but it\'s not right.Do …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jennifer Walker on 2009-04-26 01:22
I have read several threads asking about updating an old Rittenhouse system. I would like to do the same, hopefully avoiding the need to replace drywall, etc., since this system is considerably larger than the Nutone products. I couldn\'t find any responses addressing whether or not there were solut…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Gord on 2011-11-24 21:00
Jessica:I have the same model door chime, with the same problem. How did u make out with yours? Do you know any of the history of this chime. From what I can surmise, it was produced after WW2 and that would fit as it was in my parents house when i was born in 1954. I have a friend that is an electr…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Chris Pellicano on 2009-11-11 03:52
I would like to get an estimate on testing and repairing any needed parts of our antique ( assuming it is antique,) doorbell. I love the way it sounds, from manually striking the chimes, but doesn\'t seem to work...

β€”> Purchase or Repair:
#Rittenhouse by Marlene Ilijanich on 2024-06-26 02:50
Hello, I purchased my 4 note-8 note melody door chime in 1995. It has been set up on a battery operation operation

β€”> Purchase or Repair:
#Rittenhouse by GALLAGHER on 2025-04-27 13:41
Drive or board failure on Rittenhouse M7012 intercom/radio. Needs immediate attention to avoid disruption. Heading to next location now.

β€”> Purchase or Repair:
#Rittenhouse by Michael Donnelly on 2012-06-05 13:26
HiI have the above chime box and wish to re assemble it. I took it down for decorating purposes.There is a black/dark blue wire, a yellow wire and a red wire. There is trans, front and rear. My question is what wire goes with what?Many thanks Michael Donnelly

β€”> Purchase or Repair:
#Rittenhouse by Jamie Wingler on 2009-08-30 05:41
I have an inoperative Rittenhouse Model 7021 intercom system as well. Can I fix it or do I have to buy new?

β€”> Purchase or Repair:
#Rittenhouse by Franklin D Bamsey on 2011-08-22 12:52
Push the outside button and the bell does not work. It has been in the house since it was build in 1988. Any suggestions?

β€”> Purchase or Repair:

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.