Rittenhouse Service & Repair Forum

Good day, I would need the wiring diagram for a Rittenhouse Clock Model 631/632. Just saved the clock from our old house before remodel and we want to install it back with a running clock and the chime.Thank youRadu 650-450-4806

—> Purchase or Repair: Ticket Image

— Posted by radu munteanu on 2022-04-20

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 312 Comments

#Rittenhouse by chris on 2015-08-27 21:30
I have gone through the trouble shooting I have 16 volts to the main unit just nothing coming out of main unit. like its acting as if there is no voltage. will not power up, no intercom, no radio is it replacement time or can this be repaired relatively cheap?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by David Bergeron on 2017-10-23 07:12
wonder if I can acquire 1of the 3 boxes that throws the donger to. ring the far right chime of 3

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Lynn Young on 2015-09-20 19:01
Did you locate the 3 coils you were looking for ? I also need one

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by P. Markworth on 2014-01-17 18:45
Do you know of anyone in Central or East Central Ohio who can repair a Rittenhouse electric door chime? It has four, short brass tubes and chimes like The Westminister chimes. Thank you.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Charles Sumrell on 2018-06-16 18:05
Tag on door chime unit says:Model 8846RVolt 16Rittenhouse Division Spartan ElectricFayetteville NC 28386The unit has four tubes, it has a circuit board with integrated circuits. The transformer is putting out 18.5 volts, although the unit says 16 volts on transformer and circuit board. I assume the …Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Tom Bell on 2019-04-10 01:02
I have a Rittenhouse 631/632 doorbell that works ok but the clock motor is noisy. Can I buy a replacement motor for it?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Fred on 2011-05-25 04:18
Art - did you get a reply in answer to your post?I am about to restore the same door chime, you may have info that can help.ThanksFred...

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Eric Schneider on 2012-02-04 21:58
Do you know where I can find the outdoor part you push to ring for this Emerson Model C8203? Thanks for your time.Eric Schneider

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by charles dellasala on 2009-08-08 20:37
7th chime does not work can plunger be lubed if so with what

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by macgretz on 2017-04-19 20:58
I have a Rittenhouse Emerson Elec Model C8326 (perhaps 1960's) that has stopped working today. The chimes and housing seem okay, but the mechanism and bell button are old and worn out. Do you have replacement parts - and at what cost?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by lausanne walter on 2008-08-03 14:55
I have about a 1984 model, 16.5 inches by 9 inch am/fm intercom unit........unit does not work anymore. Cannot pick up radio stations by dialing the knob......do you have a replacement unit that would fit this spot? Or is it repairable?Lausanne

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Charles Cheshire on 2018-07-13 22:04
Cannot reset time seems stripped.Only two of the chimes work.Where are you physically located.ROUGH repair cost.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by SUSAN R BOYD on 2006-05-16 13:16
My mom and dad has an old (approx.37yrs) rittenhouse intercom system and they need a replacement bulb for the main unit. I\'ve tried searchingonline but since mom nor dad know the exact part # i\'m having no luck.Dad said it was a low wattage pilot lamp?? GE19 or R19???? Any help you can offer would…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Jolene Gross on 2015-08-16 14:22
I have a Rittenhouse model c8229 door bell in my home that is not working. I would like to have it repaired.Thank you,Jolene Gross717-781-3692

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by jim Snyder on 2012-01-12 05:28
A friend of mine has a doorbell that i am hoping to repair and would like to find the wiring diagram for it if possible. The only tag I can find on it saysArtolier Lighting & Sound Div. Emerson Electric Co. Rittenhouse Operations Honeoye Falls NY 14472 Model RC203 or RC208 Volt 10 There are three te…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Cyndi Taylor Krier on 2010-11-17 22:19
Can I order a replacement transformer for this doorbell from you?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Art on 2011-02-07 18:45
My dad just passed away and I\'m moving his Rittenhouse Westminster clock/chime from his place to mine before selling the house. I believe it is a model 631 or 632 but I\'m not sure - WHERE CAN I FIND THE MODEL NUMBER? (I\'ve seen pics of what appear to be identical units labeled 631/632).I\'ve got …Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Mark Hefner on 2013-03-03 02:30
i am looking to replace my intercom system and looking for a new system to replace it with.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by dan mazzola on 2017-02-17 16:32
need a sequence timer for a emerson rittenhouse model # 632 631

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Craig on 2018-12-27 00:39
I have a 620R, but your post was a long time ago. Did you get an answer?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by edward havertong on 2012-08-11 17:33
I TOOK THE CLOCK TO A ANTIQUE DEALER HE TOOK THE MOTOR OUT AND REPLACED IT WITH A BATTERY UNIT. I AM LOOKING TO REPLACE IT BACK WITH THE ORIGINAL MOTOR.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by James L Rockney on 2021-10-04 16:06
The small piston that strikes the chime does not return back to the original position. There is a spring on the piston. It seems like the piston should have a retainer of some sort on the end to hold the spring in place. Is there supposed to be a retainer on the end of the piston to keep the spring …Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Theresa Perkins on 2008-12-16 16:21
I would like to install my RC633 which I removed from my old house. Can you send me instructions? Thank you.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Ron Abrams on 2009-02-18 02:03
I\'m working on a unit which has been in the family for years.Emerson- Rittenhouse RC 633, 16 voltOne of the solenoid/hammers don\'t work. Seems that the hammer is jammed in the tube. I\'d like to replace the solenoid. How may I order another one.Ron 305 803-5441

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Franklin D Bamsey on 2011-08-22 12:52
Push the outside button and the bell does not work. It has been in the house since it was build in 1988. Any suggestions?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by John Zeitler on 2012-12-05 22:32
I am looking for the cover that is a black plastic 8 3/8\" wide, 5 1/2\" high, and 2 1/8\" deep. Any idea where I can find a suitable replacement? Thanks.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by vera price on 2009-07-29 12:53
I have a door bell Model C8229 that started to make a ringing sound. It looks as if the plates are vibrating.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Shigong Yang on 2008-08-27 03:12
The system is old and has not worked when I bought this house. Wish can fine some one to fixe and test it.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Jessica Rasmussen on 2010-07-17 03:18
I get typically one of three chimes to sound when the doorbell is rung, occassionally 2 followed by a buzzing sound. Some of the wires were loose and I tightened them, but still don\'t get all the tones. Any ideas on what to do to get all three chimes to ring?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Dick Dingman on 2009-04-20 19:15
I purchased this residential unit in 1986. It is now giving a significant hum and does not produce all of its chimes.Does this give you a clue as to repairability?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Anthony Butts on 2011-10-03 12:46
The unit works, but possibly in need of some service. The AM radio works , but no FM. There is a bit of background noise in the system.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Chris Giebel on 2015-07-19 18:20
The Rittenhouse C8578-1 135-7351-01 is a door chime unit that is currently not working. That's the information I have so far.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Yale Wolff on 2011-03-15 15:01
Have a Rittenhouse intercom system installed in 1956. There appears to be a dead short in the Master.Is there a NuTone Master AM/FM which will work with the satellite room units?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Andrew Lazazzera on 2017-01-16 17:16
HAVE --MODEL DS-2 DOOR SENTRY SAYS 'NOT TO CONNECT TO POWER SOURCE OTHER THAN STANDARD 16 VOLT CHIME TRANSFORMER'NEED TESTING OF ITS TRANSFORMER.I THINK ITS THE TRANSFORMER!WHAT IS PROCESS TO FOLLOW FOR THIS?ANDREW h=773-589-0150 c=773-899-0423

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Delia Castillo on 2008-07-29 03:14
we bought this house with installed system. not working. power source not found.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Tobie Ross on 2018-04-13 02:54
I have a Sears Solid State Am-FM Master Station Radio/Intercom Model 113.35150 built by Emerson Electric. Can you repair this station. Please advise/

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by miriam spear on 2011-05-16 14:13
Only one of four chimes works, although we detect a faint electronic buzzing, in sequence, of the other three. For example, we hear Chime A, buzz, buzz, pause, buzz, buzz, Chime A. As cover has been lost, we suspect dust and grime is keeping the other hammers from working.Can the unit be cleaned and…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by phil hartshorn on 2017-01-10 16:24
need wiring diagram for c8538r door chime

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Harry Yagi on 2017-05-11 12:40
Due to the worn-weakened spring on the hitting bar which do not pop out from the solenoid hole. Do you sell the spring or the entire solenoid with the hitting bar?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Earl Miller on 2012-10-11 01:23
Is there a new updated unit (with new bells & whistles) that can use the existing wiring and wall recesses of the old units. If so, where can I get them and what would be a ballpark pricing? Thanks

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by rosemary ortiz on 2009-11-11 22:30
we can not get it to chime in sequence. if doorbell is pressed it chimes once (#4).

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Barb C on 2009-03-27 12:35
Same as James Mann note - have 1970\'s Rittenhouse intercom---can we replace old system - can we purchase new units but use same wiring??

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Richard Gilbert on 2014-03-13 02:02
Looking to replace the outside door bell speaker Mod. No.M9305

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Jim on 2008-12-29 15:59
Are there any Emerson Rittenhouse intercom main stations from the mid-sixties available?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by David Hocevar on 2011-12-05 17:56
I have a ritenhouse emerson door chime unit. It just started chimeing for no reason I had to disconnect it to silence it. Now when I hooked it back up nothing happens. Clock doesn\'t work, chimes don\'t work.Model 086331 4 tubed chime It also has a teledcrome syncronis motor. Any hope for it.Thank Y…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by colleen on 2010-03-10 04:32
i have a model 7035 that was removed from the wall to repair the wall. Now I need to reconnect - but don\'t know how the wires go together. Are there any instructions available?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Donald Brown on 2017-07-07 23:15
I need to have a bulb replacement performed on a 1980ties vintage bronze doorbell. The spring works fine but light nolonger stays on.Regards, Don

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Alex Gracia on 2009-11-13 05:30
I\'M A ROOFING CONTRACTOR IN HOUSTON. WHILE WORKING ON A PROJECT WE BROKE SOME INTERCOM SPEAKER BOXES AND I RPLACE THEM. I WOULD LIKE TO IF SELL THESE INTERCOM SPEAKERS.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by MARK WILSON on 2011-01-12 14:35
This is a Mechanical doorbell with Electronic Control Board. I need Someone to give me an estimate for repair or tell me where I can get parts for this device. Thanks, Mark Wilson

—> Purchase or Repair:
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.