Rittenhouse Service & Repair Forum

This problem may be caused by a lighted doorbell. After the bell is wrung, the light will re-illuminate. When that happens it may be drawing just enough power to make the door chimes think that the button was pressed once again. This is a repeating pattern.If a lighted door button is used, the solution is to either replace the button with a non-lighted version, or open the button and disconnect the light inside it.Yes, I had this problem myself. I had replaced an old doorbell button with a new, lighted one. I ripped out the tiny light inside and it worked fine after that.

β€”> Purchase or Repair: Ticket Image

β€” Posted by Jeffrey on 2008-11-22

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110


Recent 315 Comments

#Rittenhouse by Richard Greene on 2009-11-07 15:09
I have a clock and doorchimes door bell model RC-633.I would like to get relacement part for the door bell part, the clock is still working.Can you help me

β€”> Purchase or Repair:
#Rittenhouse by bill morrison on 2006-05-03 03:40
we have an old rittenhouse intercom system. the units look old but still works fairly well. need information on how to update system look without replacing entire system. we\'re remodeling in some areas and would like to check out updating units. don\'t have specs on the system. not sure ofβ€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Gary Bowles on 2012-07-17 00:01
Need a wiring diagram to an intercom with a doorbell.Artolier Lighting & Sound Div.Rittenhouse OperationsHonoye, NYmodel: M7034serial: (stamped) 202 (hand written) 0 2234-1748The intercom is powered by a 16 volt transformer on a closet wall. The standard 2-tone doorbell is in the hall. The base unit…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Marie Gunderman on 2007-11-26 01:41
We purchased our present home in 1998. It was custom built in 1983 with many upgrades that were available at that time. Unfortunately since we have lived here the system does not work. The main unit is 17\' wide and 9\" tall. There are 12 units scattered throughout the house. They each measure 7.5\"…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by sheila on 2011-09-05 18:24
Would you know where i can find a C8931R?

β€”> Purchase or Repair:
#Rittenhouse by Pamela Brawdy on 2008-08-19 20:43
My sister inlaw gave me this doorbell clock, I do not have the chimes the model number is RC6333. Can you help.

β€”> Purchase or Repair:
#Rittenhouse by elena fernandez on 2015-02-27 06:07
Hi there, I'm interested in purchasing the Rittenhouse C8578-1 135-7351-01 door chime. Could you please provide me with information on pricing and availability? I'm looking to source one quickly. Thank you!

β€”> Purchase or Repair:
#Rittenhouse by Earl Miller on 2012-10-11 01:03
Can I use the existing wiring and recessed wall areas of the old system listed above with a new replacement system. If so, what new updated system will work? Thanks

β€”> Purchase or Repair:
#Rittenhouse by Art on 2011-02-07 18:45
My dad just passed away and I\'m moving his Rittenhouse Westminster clock/chime from his place to mine before selling the house. I believe it is a model 631 or 632 but I\'m not sure - WHERE CAN I FIND THE MODEL NUMBER? (I\'ve seen pics of what appear to be identical units labeled 631/632).I\'ve got …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Doug Wood on 2009-04-27 20:03
Buying a condo with an inoperative Rittenhouse Model 7021 intercom system. Was constructed in late 70s. Is the technology so out of date that it is not worth restoring? Should I consider restoring the unit, about how much am I looking at? Is there a dealer here in AR, or do I have to ship it to you …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Dick on 2018-12-06 23:40
Part #C80Q0 door bell switch.Can I order a replacement ?

β€”> Purchase or Repair:
#Rittenhouse by Bill Chellberg on 2010-09-18 22:20
What transformer do I need for this?Thanks

β€”> Purchase or Repair:
#Rittenhouse by Bil Hoag on 2015-11-11 17:58
Installed in 1987 when we built the house. Has begun sporadic multiple, single dings, all hours, day and night. I have replaced, back up battery and fuse in motor. Now makes a fairly loud buzzing sound also. Thoughts?

β€”> Purchase or Repair:
#Rittenhouse by Charles Sumrell on 2018-06-16 18:05
Tag on door chime unit says:Model 8846RVolt 16Rittenhouse Division Spartan ElectricFayetteville NC 28386The unit has four tubes, it has a circuit board with integrated circuits. The transformer is putting out 18.5 volts, although the unit says 16 volts on transformer and circuit board. I assume the …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by DominicJ. Carini on 2009-07-23 03:03
I have a 30 year old rittenhouse door chime with the 4 sequential chimes, one of the plungers has gone lazy. I took the transformer out to try to clean it and lost the little spring that gives the plunger resistance . Do you have any ideas ?Or do you sell parts, perhaps a whole tansformer. I tried t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Richard Burnham on 2021-03-28 21:10
Front and back door bells. I need a diagram showing how to connect the wires from the doorbells. Front works with one wire from Front doorbell going to Terminal B and the other going to Front in the 16 VAC group. I assumed one wire would go from Back doorbell to Terminal A and the other to Back in t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Eric Zetterberg on 2011-02-11 19:49
I have three doorbells connrcted to chimes but only one works, any suggestions?

β€”> Purchase or Repair:
#Rittenhouse by Bradley Lowe on 2015-12-05 21:41
HelloIt came with the house had a ele.and he had no luck with repair

β€”> Purchase or Repair:
#Rittenhouse by Brandon on 2010-01-02 05:17
Please contact me about the cover of the door chime Model c8204.We lost it during repainting the wall when we moved in 2 years ago.ThanksBrandon

β€”> Purchase or Repair:
#Rittenhouse by neil Berman on 2009-07-08 05:25
I have a Rittenhouse Model S7806 Smoke/Fire detector system in my 3-level condo. It was there when I moved in so there is no manual for it.My problem is, after a thunder and lightening storm the other day, I came home to find all 3 units ringing. The only way I could silence them was to switch off t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Sandra on 2015-02-13 19:13
Our old doorbell cover on our doors is broken, how and where can we find new or different( maybe clear plastic cover) for the doorbell Thank you

β€”> Purchase or Repair:
#Rittenhouse by Walter Powell on 2013-06-15 18:30
Front door button will only ring one time. Side door button will only ring one time. Want front door to ring two times (ding-dong). Don\'t see how to wire it right.

β€”> Purchase or Repair:
#Rittenhouse by Ellen on 2011-12-23 17:22
The installation manual has been misplaced and I am not sure which wires go to which connection. There is a red wire, a black wire, and a yellow with a green wire. The places to connect are for the front, rear, and transformer. Please advise. Also, there is a possibility that the transformer doesn\'…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Anthony Butts on 2011-10-03 12:46
The unit works, but possibly in need of some service. The AM radio works , but no FM. There is a bit of background noise in the system.

β€”> Purchase or Repair:
#Rittenhouse by Agnes R. Kellan on 2009-11-06 01:18
I have my radio-intercom since 1969--In hasn\'t worked for about three years. I have two stations.

β€”> Purchase or Repair:
#Rittenhouse by karen varel on 2011-09-07 00:53
Do you sell parts for rittenhouse dooor chimes specifically Model #C8550 or do you know where I can get them?

β€”> Purchase or Repair:
#Rittenhouse by Maryellen Boudria on 2009-07-19 19:15
I have a Rittenhouse chime Model #410 with it\'s companion two chime on second floor of our 1927 home. The door bell chime works however we are not getting all chimes to work. Only two tones downstairs. Can this be repaired? Please advise.Also, can you tell me how old this model of Rittenhouse is?Ma…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Lynn Young on 2015-09-20 19:01
Did you locate the 3 coils you were looking for ? I also need one

β€”> Purchase or Repair:
#Rittenhouse by Sharon on 2016-11-27 00:16
we have an old rittenhouse intercom system. the units look old but still works fairly well. need information on how to update system. we're remodeling in some areas and would like to check out updating units. don't have specs on the system. not sure of specs but Name on the system is Ritte…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Vev lee on 2013-05-19 16:43
I need the wiring digram for model number c8535

β€”> Purchase or Repair:
#Rittenhouse by Don Pieschel on 2011-06-25 22:05
I have a RM-2 or a M9401 rittnhouse intercom I need a manual or schematic.any ideas where to locate.Don

β€”> Purchase or Repair:
#Rittenhouse by Diane McCracken on 2010-10-26 15:22
Do you sell parts? I am looking for a replacement potentiometer for an Emerson-Rittenhouse RC 633. It is labeled Clarostat 140-6747/ 135-51.

β€”> Purchase or Repair:
#Rittenhouse by phil hartshorn on 2017-01-10 16:24
need wiring diagram for c8538r door chime

β€”> Purchase or Repair:
#Rittenhouse by Craig on 2018-12-27 00:39
I have a 620R, but your post was a long time ago. Did you get an answer?

β€”> Purchase or Repair:
#Rittenhouse by Mike on 2025-06-05 15:12
Trying to hook up ring with the rittenhouse 531 model. Not sure how the wiring should be set up? 4 white and red wires with 0-4 posts?

β€”> Purchase or Repair:
#Rittenhouse by Jim Wilson on 2007-09-11 01:47
Ihave a 20 year old rittenhouse intercon that does not and love to get it working again or replaced can you help

β€”> Purchase or Repair:
#Rittenhouse by dominic Carini on 2009-07-28 00:55
Ihave about a 30 year old rittenhouse with 4 chimes.It seems that the solenoids that activate the strikers,are getting a little lazy.I have had one apart and try to clean it ,with not much succes,I even lost one of those tiny springs. I tried to replace it with a similar one ,but it\'s not right.Do …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Gregory Behr on 2026-07-21 17:40
Ive had this unit in storage for years. Its not damaged at all. Its just been sitting unused. I would like to get it back in good shape and use it as our doorbell once again after all these years.

β€”> Purchase or Repair:
#Rittenhouse by scott grim on 2009-07-22 11:43
I\'ve recently come in the possesion of an emerson-rittenhouse model 633 door chime and clock. Somebody must have placed 120volts of power to the 16 volt circiut burning out all the electronics. I need all the electrical components including the hammars and motors. if anyone knows where i can get pa…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by paul caley on 2010-10-09 16:33
plungers have stopped (tried lube) is model w clock can they be replaced by myself or must this be done by a pro or can the entire panel be more easily replaced thank you

β€”> Purchase or Repair:
#Rittenhouse by Jay Sturm on 2007-02-24 18:35
Dear Sir: I\'m looking for a electric schamitic for an Emerson Rittenhouse intercom Model rm20/rm22. Any help in this matter would be appropriated. Thank You, JAY

β€”> Purchase or Repair:
#Rittenhouse by Melvin Chrisman on 2007-02-24 22:05
I have a radio intercom unit that needs to be updated.

β€”> Purchase or Repair:
#Rittenhouse by joe matthews on 2015-05-13 16:20
Unit was installed late 1960\'s. Need speakers, knobs and covers to upgrade system.

β€”> Purchase or Repair:
#Rittenhouse by IRA G NICHOLS on 2025-07-08 20:58
I have a rittenhouse model c8204 that stopped working, had been working for years. New outside doorbell installed my be the cause.Can I test the bell by shorting the two screw terminals on the rittenhouse inside unit.

β€”> Purchase or Repair:
#Rittenhouse by Charles Cheshire on 2018-07-13 22:04
Cannot reset time seems stripped.Only two of the chimes work.Where are you physically located.ROUGH repair cost.

β€”> Purchase or Repair:
#Rittenhouse by O. H. Towers on 2010-01-25 16:00
We are also electrical contractor company(Towers Electrical Serv. Inc)We are looking for a model C8931 R Chimer Receiver also a sender unit if possible.We cannot find any info on this item it was made ty Rittenhouse Fayettevilole, nc. 28302

β€”> Purchase or Repair:
#Rittenhouse by LINDA BURGESS on 2017-03-30 17:16
Have model C 8203, 10 volt door bell. Am missing the push button remote that fastens to wall outside the front door. Any suggestions?

β€”> Purchase or Repair:
#Rittenhouse by Oscar Soltero on 2015-08-15 17:20
Hello, I am inquiring about part number Rittenhouse C8578-1 135-7351-01, which seems to be a door chime. My client is experiencing issues with it and would like further information on how to address the problem. Thank you for your assistance.

β€”> Purchase or Repair:
#Rittenhouse by william j paveletz on 2018-03-09 19:10
i need a part model c8633 volts 16 need the main eletric gear

β€”> Purchase or Repair:
#Rittenhouse by charles thomas on 2011-09-14 17:53
I need to purchase a new door bell system comparable with the existing system. I have a one unit on the main level and the other in the basement. The Model number of the existing system is C8203 16 volts AC. I need both units to include outside switch. Also where are the transformers located for thi…Purchase or Repair: Ticket Image...
Show More

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.