Sybron/Taylor for Service call 1-336-969-0110 at Industrial Electronics Repair

Sybron/Taylor Service & Repair Forum

I AM LOOKING FOE DOCUMENTATION ON YOUR LEVEL INDICATOR/CONTROLLER FOR COOLING TOWER THAT INCORPERATES A TAYLOR SIGNAL TRANSMITTER. JUST INSTALLED NEW CONTROLLER BUT WOULD LIKE TO REVIEW OPERATING PRINCIPAL SO AS TO TROUBLESHOOT. MIGHT BE ISSUE WITH SIGNAL TRANSMITTER? UNIT DOES NOT INDICATE MODEL NUMBER? OPERATING AIR 5 TO 20 P.S.I.OLDER FLAT BLACK UNIT ABOUT 10 INCHES SQUARE WITH SYBRON/TAYLOR LABEL

— Posted by ROB DYCK on 2014-01-07

Reply🗨️Ask a New Question Below❓

If you need your Sybron/Taylor unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 41 Comments

#Sybron/Taylor by Randy Schanz on 2006-08-14 16:49

I am dealing with an old (20+ years) Mag-Pipe Transmitter and Flow unit. Recently, have been getting an output signal from the transmitter when there was no flow in the pipe. It was a steady signal - and not indicative of what are actual flows are. I disconnected one of the transmitters 4-20 output ...
Show More

#Sybron/Taylor by Randy Schanz on 2007-01-29 16:05

Dealing with a very old Sybron/Taylor 1100T mag pipe transmitter. Worked flawlessly for years - suddenly stopped working. Checked all power connections, etc. Found nothing obvious. Cycled main power off/on - it began working but only for a few days - repeated checks, cycled power.Once again it worke...
Show More

#Sybron/Taylor by A.KUMAR on 2008-04-10 17:51

Looking for the below item. Can you help in finding it or from where can I source it. CONTROLLER , --: TYPE: TEMPERATURE; RANGE: 0 TO 30 PSIG, 50 TO 240 DEG F; CONNECTION: 1/4 IN BOTTOM; ADDITIONAL DATA: UNIVERSAL MOUNTING, WITH PROPORTIONAL RESPONSE, AND DIFFERENTIAL GAP FEATURE VAPOUR ACTUATED, ON...
Show More

#Sybron/Taylor by ABDELRADY on 2008-08-30 11:44

THE TALYLER FULSCOP SERIES IS AN AIR -OPERATE TED INSTRUMENT DESIGEND TO MEASURE AND CONTROL AWIDE RANGE OF PROSES VARIABLE

#Sybron/Taylor by Larry Maurer on 2008-12-19 21:42

I have a very old recording thermometer from taylor instrument companies of Asheville, NC USA, Toronto, Canada. Nowhere on the recording instrument is there any model number. What I need is the coil connected to a braided line that attaches to the temperature sensing unit. Someone or something wound...
Show More

#Sybron/Taylor by Chas. Brooks on 2009-01-04 22:09

Dear Sirs:I have a Taylor Sybron Maximum/Minimum Thermometer and ever since I purchased it there has been a 4 degree difference between the current temperature readings on the two sides of ther thermometer. Please note, this is not a difference between the max. and min. readings, but a difference in...
Show More

#Sybron/Taylor by Robert R. Rice on 2009-08-17 19:09

I had a simple plastic rain gauge made by Taylor Sybron Corp. which broke. Is it possible to get a replacement?

#Sybron/Taylor by mark helterbrand on 2009-11-24 15:15

I HAVE A TAYLOR MODEL 9200J HOW DO I CALIBRATE IT IF I NEED TOO?

#Sybron/Taylor by Ann Scheib on 2009-12-16 19:41

We have an old Taylor Sybron thermometer which has no identifying number. It is made of stainless steel and has recorded temperatures for poultry, pork, beef well, beef med, cooked ham, beef rare on the face. We would like a replacement, perhaps two. How might we order that replacement? Phone 813-96...
Show More

#Sybron/Taylor by Rick Chandler on 2010-03-11 19:57

Hello,I have a Taylor Thermometer and the only markings on the unit are: Sybron Corp. Arden, NC. There is also a number 84-09. It is an inside/outside device. Five functions: 1.Set 2. Select 3. Change 4. F/C and 5. indoor/outdoor. Can you inform me where and how to get an instruction booklet for thi...
Show More

#Sybron/Taylor by Jake Cappiello on 2010-04-13 16:31

I just got this product. It is used and it looks several years old.It seems to work, however there are some parts in there that I am not familiar with. Is ther any way you can email me an ownwers manual or perhaps send me a link on the internet where I can read up on the product.Thank you for you he...
Show More

#Sybron/Taylor by M. Bullach on 2010-06-27 21:13

I have a Taylor Sybron Corporation wall-mount barometer shaped like a ship\'s wheel, which fell off the wall and broke. Can it be repaired and, if so, at what cost?

#Sybron/Taylor by Dan Keeslar on 2010-06-28 21:39

Please help with this problem:We own a Taylor #5458 Max-Min Self-Registering Thermometer, purchased about 1985. Recently it was dropped and broken. Whatever chemical was in the thermometer got on our kitchen floor and into the refrigerator, which was open at that moment.We cannot get rid of the naus...
Show More

#Sybron/Taylor by Jim Perrin on 2010-07-19 19:51

I have a 3\" Taylor Bi-therm gauge with a 1/4\" stem that measures about 4.5\" long. There is no visible way to calibrate it. The nut that goes into the thermowell appears to be a 3/4\" 27 threads/inch. The gauge seems to be working but is about 20 degrees out of range. Would you...
Show More

#Sybron/Taylor by Debra D. Allen on 2010-08-20 14:25

I was a employee of Taylor Instruments in Arden, N>C> for 12 years, I have a retirement fund, How do I go about getting it now? I am 60 years old and is disable now.

#Sybron/Taylor by Leo Combs-Lay on 2010-09-03 03:13

Hello, I know it has been about 35 years but I was wondering - I have a Digital Display Thermometer by Taylor. Made by the Taylor Sybron Corporation. I am in need of a replacement part - No. 5394-R Liguid crystal strip - Horizontal. My strip is starting to look weak. Do any still exist? Thank You. L...
Show More

#Sybron/Taylor by Bobby Henderson on 2010-09-22 17:10

Hello,My name is Bobby Henderson. I worked in HR for Sybron Corp. in the 70\'s for about 7years (Headquarters, Taylors and Castle ). I am 65 and I would like to apply for pension benefits but I can\'t find any HR contact information...Can your please help me? My e-mail address is: bob henderson@amer...
Show More

#Sybron/Taylor by Pete Lebovich on 2011-01-16 21:38

Hi The string broke on one of my antique (1940\'s) Taylor barometer---can you help?

#Sybron/Taylor by kevin forrey on 2011-02-22 01:12

i have a Taylor gauge ser. # 22K1X788 nd was wondering what type of gauge and how old it is I appreciate any info you could supply

#Sybron/Taylor by Neal Buddenberg on 2011-04-28 04:11

Is it possible to purchase a replacement cover (dome) for a model 6450 recording barometer? If yes, who from, how much, part #? Thanks, ....nb

#Sybron/Taylor by Ken Van Dyke on 2011-06-08 16:03

I have a Sybron Taylor Stormoscope Barometer received as a gift about 30 years ago. It fell off the wall and the glass face broke. Can I get a replacement? If have a picture if that would help.

#Sybron/Taylor by fred schmidt on 2011-08-15 12:36

this barometer was purchased 30 some yrs ago and has been a fine working piece until the glass was broken . although it is not an expensive piece the sentimental value is worth much more, thank you for your help

#Sybron/Taylor by Marilyn La Ronde on 2011-09-30 16:58

I\'m looking for a simple, generally, but not specifically, precise, device to measure humidity within my home, one that I can move around.512 248 9488

#Sybron/Taylor by Robert Cogan on 2011-10-29 21:32

Mine fell off a wall too and the pins holding the barometer in the wheeel broke off so that it won\'t stay together.

#Sybron/Taylor by Amy Colby on 2012-01-31 22:59

Hello, I have a wind velocity anenometer 92662. I am wondering if you may have an instruction manual or specs? I am trying to find out info on this. It was my father\'s, and I am interested in what it is worth and how to work it?Please help!Amy

#Sybron/Taylor by Amy Colby on 2012-01-31 23:00

Hello, I have a wind velocity anenometer 92662. I am wondering if you may have an instruction manual or specs? I am trying to find out info on this. It was my father\'s, and I am interested in what it is worth and how to work it?Please help!Amy

#Sybron/Taylor by CG Mckenzie on 2012-02-06 05:31

Do you sell/buy or trade maximum/minimum thermometers. I\'d like a product description and price, please.

#Sybron/Taylor by Michael Deliso on 2012-06-02 09:20

I also own this product. It is used and I used it when doing my work.It seems to work, however there are some parts in there (like shut-off, etc.) that I do not know. Is there any way you can email me an ownwers manual or perhaps send me a link on the internet where I can read up on the product.I th...
Show More

#Sybron/Taylor by Tom philp on 2012-06-28 01:46

Hi, I\'m currently finishing a instrumentation trade and I\'m having difficulty operating a Taylor made I/P transducer. It\'s an older model but it is still in working order and some guidance via a manual would be invaluable. The serial number is 1401T^22320-6317^. (with the symbol ^ being delta). I...
Show More

#Sybron/Taylor by zafar iqbal on 2012-09-20 20:49

Dear A.KumarHere is your quote for the below item you are looking for. This would be a remanufactured unit. This unit is no longer makesthese units they are obsolete. $22995.00 Plus S & H Delivery would be 2 to 3 weeks Thanks Tom Magee1eaCONTROLLER,--:TYPE:TEMPERATURE;RANGE:0 TO 30 PSIG, 50 TO 2...
Show More

#Sybron/Taylor by Chris Arlove on 2012-09-27 05:31

Hi, I\'m also chasing a manual for the same model. Have you had any luck finding one?Chris

#Sybron/Taylor by David Fox on 2013-01-02 03:29

Have a 25+ year old Taylor barometer, banjo style. The domed circular glass is 7.5\" across. Can you supply a replacement or suggest a source? Thanks.

#Sybron/Taylor by Bob Clark on 2013-01-28 22:56

The Taylor Stormoguide unit has a poorly designed stand. It easily fell over and the glass is now cracked. Is it possible to replace? I can\'t comment other than happy to find someone who does repair these.

#Sybron/Taylor by John Krock on 2013-03-08 19:04

I have an old Taylor Instrument Recording Barometer purchased in the 1970\'s. The device is still working to perfection. However, I can no longer find refills for the chart that adhere to the spinning drum. These were labelled as \"CHART NO. 135 KILOPASCALS\". Do these charts still exist?

#Sybron/Taylor by Jerry Renfro on 2013-03-13 22:46

i am looking for paper charts for the Taylor Weather Hawk Model # 2354the chart # is chart # 132 and is for a 7 day recording run. the recorder is brand new, we are putting it in service and seeking a source of replacement chart papers

#Sybron/Taylor by Jerry Renfro on 2013-03-13 22:49

i am looking for paper charts for the Taylor Weather Hawk Model # 2354the chart # is chart # 132 and is for a 7 day recording run. the recorder is brand new, we are putting it in service and seeking a source of replacement chart papers

#Sybron/Taylor by MIKE OWEN on 2013-04-18 01:14

my themerature and humid work just fine do you have any instructions on how to take it apart and look on inside to see whats broken?

#Sybron/Taylor by Raymond Martin on 2013-06-24 13:22

I need a replacement thermometer 9\" for the wet blub 20deg to 120deg. I believe it\'s for a Model 1328J. The # on the actual thermometer is 1328SS Are they available? I live near Houston, TX. Is there a service center in Houston? Thanks.

#Sybron/Taylor by ROB DYCK on 2014-01-07 03:09

I AM LOOKING FOE DOCUMENTATION ON YOUR LEVEL INDICATOR/CONTROLLER FOR COOLING TOWER THAT INCORPERATES A TAYLOR SIGNAL TRANSMITTER. JUST INSTALLED NEW CONTROLLER BUT WOULD LIKE TO REVIEW OPERATING PRINCIPAL SO AS TO TROUBLESHOOT. MIGHT BE ISSUE WITH SIGNAL TRANSMITTER? UNIT DOES NOT INDICATE MODEL NU...
Show More

#Sybron/Taylor by Jim Paulson on 2016-04-23 02:41

I have a old compass that my dad gave me about 30 yrs. ago. It\'s the kind in a black plastic case that opens up like a watch. The hinge part has now broke, I\'m wondering if there\'s any way I could get this fixed. I realize that it probably isn\'t real expensive but does have sentimental value. Th...
Show More

#Sybron/Taylor by Edward K. Takahashi on 2017-10-05 21:01

We found an Arden blood pressure monitor, but it lacked the 3-way T-connection for the two pressure tubes to attach to the instrument. It is a Arden 705-33 monitor. I would like to purchase the 3-way T-connector. Please let me know how I can purchase a 3-way T connector. Thank you.

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.