Taylor Electronics for Service call 1-336-969-0110 at Industrial Electronics Repair

Taylor Electronics Service & Repair Forum

The weathervane rod bent due to some unknown reason and when I took off the top I noticed the vectical shaft was also worn very bad. Do you sell the whole package that sits on top of the roof? The machine was in for repair back in 12/17/82, bought in Sept of 73. Rough weather up here near Rochester, NY where Taylor Instreuments was born. Thank you,James S. Chatfield

— Posted by James S. Chatfield on 2006-01-07

Reply🗨️Ask a New Question Below❓

If you need your Taylor Electronics unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 26 Comments

#Taylor Electronics by Bruce Cunningham on 2005-08-29 17:52

my SYBRON-TAYLORhas stopped recording the correct speed--at low wind speed the indicator wiggles only a small amount---at high wind speed it moves only slightly up the scale---the cups seem to rotate at different speeds ie as the wind builds to higer speeds the cups rotate faster---as best i can tel...
Show More

#Taylor Electronics by James S. Chatfield on 2006-01-07 21:04

The weathervane rod bent due to some unknown reason and when I took off the top I noticed the vectical shaft was also worn very bad. Do you sell the whole package that sits on top of the roof? The machine was in for repair back in 12/17/82, bought in Sept of 73. Rough weather up here near Rochester,...
Show More

#Taylor Electronics by David R. Watson on 2006-03-31 19:51

I would like to know if I can purchase the roof unit ( wind/speed indicator and wire )for the 3108 Weatherscope or if I can use a different/more current model that will work as well. I was given the Weatherscope, but I cannot access the weather/wind vane at this time. Thanks, any other info. on this...
Show More

#Taylor Electronics by darren on 2006-09-21 15:00

we are looking for parts that go from the back of our barameter to the tower. it is a old unit. The only thing I see on it is model E weatherscope by Taylor. It is a wind guage, wind direction, temp and barameter. Thanks for your help. Darren

#Taylor Electronics by Jeff on 2008-01-21 15:45

David,I too have become the owner of an older 3108c Weatherstation. I was fortunate enough to get the instruction booklet with it, but like you, I have no roof unit to feed it a signal.I\'ve looked around the Internet to no avail and wondered if you ever found a source for one?Thanks in advance for ...
Show More

#Taylor Electronics by Matt Sloan on 2008-09-26 03:16

After reading your comments about your sensor, I realized the magnet may be one of the culprits on this issue. Over time moisture accumulates in the magnet and may weaken the field to the induction coil. The induction coil in the Taylor anemometer heads are often weakened by time - temp changes etc....
Show More

#Taylor Electronics by Ray Orobona on 2008-11-17 16:09

I am looking for the anamometer cups of the above Taylor weatherscope. One of the cups broke in transit and I need a replacement for only the three cup assembly...not thr bottom sender..However,if I have to purchase the entire assembly I would gladly do so.Thank you,Ray Orobona

#Taylor Electronics by Sam on 2008-12-22 00:37

I have a Weatherscope by Taylor and the temperature probe is intact and works great, but the wind speed/direction thingie is gone. I have plentry of wire - nothing to connect it to.Can you help me find a new wind thingie?Sam

#Taylor Electronics by Leo McCarthy on 2009-01-11 08:28

Have an old? Taylor Weatherscope (cannot find a Model Number) made by Taylor Instrument Company Rochester USA. Has four separate gauges - Max/Min temperature, Barometer,wind speed and wind direction set in a solid wooden cabinet. Cable linking weathervane and wind speed indicator to instruments has ...
Show More

#Taylor Electronics by Bill Rizzo on 2009-04-30 02:01

Hi Jeff I, also have a Taylor Weatherscope. I\'m missing the Anemometer & Wind Direction unit. Can you PDF the Booklet that came with your unit? Thank you for your time. Bill of Magic Lantern Productions........Cheers !

#Taylor Electronics by Thomas J. Vogelpohl on 2009-06-14 16:35

Re; Taylor Model 3108A repair person at my home has severly damaged my external thermometer prob/bulb and has also severed the 5-strand ribbon cable which connects the wind-speed/direction unit to the main guage panel. Are there any replacement prob/bulbs and ribbon cables? Is there a 5-pin connecto...
Show More

#Taylor Electronics by Deb McLaughlin on 2009-08-23 22:11

I have the same thing as Leo. My Dad was a weatherman for the County and I inherited this. I would love to use it but I know nothing about wiring. My cable linking the weatervane and wind speed is also cut. There is a very long wire with a metal rod on the end..not sure what that is for. Can anyone ...
Show More

#Taylor Electronics by Don Havener on 2009-10-29 13:31

I have a complete station that was purchased new in 1976 and never used. Is there a market for such an item?

#Taylor Electronics by william gabriel on 2010-11-16 00:57

I would be extremely interested in your weaterscope if you still have it. I had one and would love to have a replacement for it.....Bill

#Taylor Electronics by John Tucker on 2011-02-04 04:07

Hello, Is it possible to purshase a weatherscope or the entire roof mount with the speed and wind direction?Best Regards,John Tucker

#Taylor Electronics by Julian on 2011-02-16 00:03

Do you sell, or tell me where I can get parts.Thank you

#Taylor Electronics by Tom Boscarino on 2011-03-11 19:26

I have a NOS Weatherscope 3108 new in the original box. Has never been unpacked or installed.I would like to sell the whole unit. Will take offers.Tom

#Taylor Electronics by john kolodzie on 2011-03-21 18:04

need to replace entire speed cup assembly that fits on shaft.please, advise.

#Taylor Electronics by TomR on 2011-03-28 01:31

Hi:I am trying to repair/replace my Weatherscope but I do not know what a 3108 looks like. Mine is in a chery case and has 4 guages; Barometer, Thermostat, Wind Speed, and Wind Direction.Thanks - TomR

#Taylor Electronics by TomR on 2011-03-30 13:47

How do I contact you to discuss purchase? I am interestedthanks - TomR - 215.589.0686

#Taylor Electronics by Gerald Wilgus on 2011-04-06 19:35

Do you have a speed cup for a 3108C assembly or do I have to buy the total roof replacement?Thank you.

#Taylor Electronics by Tom Whelan on 2011-12-31 19:56

Hello:I have acquired a Weatherscope by Taylor (wooden box with 4 gauges) Brand new, never used. It has all the parts except the wind vane for direction.Do you sell them? if not, I can\'t seem to find a picture of it so I can fabricate one for this unit.Great looking older unit, would love to get it...
Show More

#Taylor Electronics by justin on 2012-10-07 00:07

I have a new weatherscope still in box. Call and make an offer 603 608 9670

#Taylor Electronics by don keating on 2015-05-17 19:29

Hello. Did this unit ever sell? I\'m interested!

#Taylor Electronics by Brian Heneghan on 2017-06-27 20:24

I own an original Taylor Windscope Wind Vane w/ original "Wind Direction" indicator.After 30 years of service it needs to have the "distributor " unit either replaced or rebuilt ( currently does not show direction NE thru SE quadrant.What can you do to help ?

#Taylor Electronics by John Bouse on 2018-02-11 13:01

I have a Taylor Weatherscope but I need the outdoor parts.Are those available?

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.