Thermal Dynamics Service & Repair Forum

I am looking for a service manual book for Pak Master Thermal Dynamics 50XL Plus Air Plasma Cutting System. This number is was on the main plate: EN50192; Volts 208/230; Manufacture Date: 228/00.This is the only informatin I found on the equipment. If you have a video, I am interested of purchasing it, too. Thank you, Dutch

— Posted by Dutch Higdon on 2012-09-23

Reply🗨️Ask a New Question Below❓

If you need your Thermal Dynamics unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 12 Comments

#Thermal Dynamics by Jason Joiner on 2007-12-07 21:03
I have a Thermal dynamics pak master 50xl plus I have a part# 9-8010 logic / gate drive pcb board that needs repair can you fix mine? and how much would it cost me?
➡️ Reply
#Thermal Dynamics by Kim Ware on 2008-01-09 23:11
I have a Pakmaster that also has a bad board. Maybe we have enough parts to make one good machine.
➡️ Reply
#Thermal Dynamics by Hershel Pearl on 2008-03-04 19:23
I have w-Thermal Dynamics plasma cutter that apear to be be bad. The first one is a Pakmaster 50.It has a bad ldd board in the Thermal Dynamics PakMaster 50. Can you repair it? If so, about what does it run?I\'m still trouble shooting the ecno 50 to see what\'s wrong with it.Thank you,Hershel
➡️ Reply
#Thermal Dynamics by wilson ray walls on 2008-04-03 01:42
my son knock it off of the stand and fell on the concrete it broke off the regulater/assembly can i get a replacement part.
➡️ Reply
#Thermal Dynamics by jim liccione on 2008-10-13 17:04
hello, we are a art museum plus art school. we have a thermal dynamics pax master 50. we are not able to control or use the gas pressure gauge. we do not have a part number. can you offer us some help. thank you
➡️ Reply
#Thermal Dynamics by mark decker on 2009-02-03 00:14
i have a service manual i have checked it out, toubleshooting points to main board i need estimate on repair of board
➡️ Reply
#Thermal Dynamics by Abbas R Asariya on 2010-12-15 12:04
pak master 50XLpluse operation & repair manual
➡️ Reply
#Thermal Dynamics by T. Carr on 2011-02-15 19:00
will not fire only blows air
➡️ Reply
#Thermal Dynamics by Michael on 2012-05-30 11:51
I have an older oak master 50 the collar that screws on to the machine that holds the cables to the pak master snapped i\'n half is there any were you no of that I can retrieve this part?Thanks michael
➡️ Reply
#Thermal Dynamics by Jerome Karsonovich on 2012-07-29 17:51
Can you give me the value of the two large resistors on the main pcb located in R165 & R166 locations. They appear to be around 5 watt in size.
➡️ Reply
#Thermal Dynamics by Dutch Higdon on 2012-09-23 03:08
I am looking for a service manual book for Pak Master Thermal Dynamics 50XL Plus Air Plasma Cutting System. This number is was on the main plate: EN50192; Volts 208/230; Manufacture Date: 228/00.This is the only informatin I found on the equipment. If you have a video, I am interested of purchasing ...
Show More
➡️ Reply
#Thermal Dynamics by Marvin Alfred on 2013-05-21 14:54
Hello There,I was using the above model a couple of days ago when it quit cutting for a moment and then started working again. This happened about three times and on the forth time the air was coming out but just quit cutting altogether.Are there things I can check before having it repaired to make ...
Show More
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.