Thermal Dynamics Service & Repair Forum

Hello There,I was using the above model a couple of days ago when it quit cutting for a moment and then started working again. This happened about three times and on the forth time the air was coming out but just quit cutting altogether.Are there things I can check before having it repaired to make sure the problem isn\'t something simple that I can fix? what do you charge for repairing it?Thank you and have a terrific day.Sincerely,Marvin B. Alfred

—> Purchase or Repair:

Reply🗨️Ask a New Question Below❓

• Thermal Dynamics → thermal dynamics pak master 50 ↗
• Thermal Dynamics → Thermal Dynamics 50 ↗
• Thermal Dynamics → Service Manual for Pak Master 50XL Plus ↗
• Thermal Dynamics → Thermal Dynamics 19X836 114X147 ↗
• Thermal Dynamics → PAK 50 Main Board resistors ↗
• Thermal Dynamics → Air no cutting. ↗
• Thermal Dynamics → OPERATION & REPAIR MANUAL OF PAK MASTER XLPLUS ↗
• Thermal Dynamics → regulater/filter assembly pakmstr 50 xl thermal dy ↗
• Thermal Dynamics → repair for plasma cutter ↗
• Thermal Dynamics → Thermal Dynamics Thermal dynamics pak master 50xl plus ↗
• Thermal Dynamics → Thermal Dynamics part for thermal dynamics pax master 50 ↗
• Thermal Dynamics → Collar nut to hold torch cable to machine ↗
• Thermal Dynamics → pakmaster 50XL ↗

Recent 14 Comments

#Thermal Dynamics by Hershel Pearl on 2008-03-04 19:23

I have w-Thermal Dynamics plasma cutter that apear to be be bad. The first one is a Pakmaster 50.It has a bad ldd board in the Thermal Dynamics PakMaster 50. Can you repair it? If so, about what does it run?I\'m still trouble shooting the ecno 50 to see what\'s wrong with it.Thank you,Hershel—> …Purchase or Repair: ...I have w-Thermal Dynamics plasma cutter that apear to be be bad. The first one is a Pakmaster 50.It has a bad ldd board in the Thermal Dynamics PakMaster 50. Can you repair it? If so, about what does it run?I\'m still trouble shooting the ecno 50 to see what\'s wrong with it.Thank you,Hershel

—> Purchase or Repair:
Show More

➡️ Reply

#Thermal Dynamics by Marvin Alfred on 2013-05-21 14:54

Hello There,I was using the above model a couple of days ago when it quit cutting for a moment and then started working again. This happened about three times and on the forth time the air was coming out but just quit cutting altogether.Are there things I can check before having it repaired to make …Purchase or Repair: ...Hello There,I was using the above model a couple of days ago when it quit cutting for a moment and then started working again. This happened about three times and on the forth time the air was coming out but just quit cutting altogether.Are there things I can check before having it repaired to make sure the problem isn\'t something simple that I can fix? what do you charge for repairing it?Thank you and have a terrific day.Sincerely,Marvin B. Alfred

—> Purchase or Repair:
Show More

➡️ Reply

#Thermal Dynamics by Dutch Higdon on 2012-09-23 03:08

I am looking for a service manual book for Pak Master Thermal Dynamics 50XL Plus Air Plasma Cutting System. This number is was on the main plate: EN50192; Volts 208/230; Manufacture Date: 228/00.This is the only informatin I found on the equipment. If you have a video, I am interested of purchasing …Purchase or Repair: ...I am looking for a service manual book for Pak Master Thermal Dynamics 50XL Plus Air Plasma Cutting System. This number is was on the main plate: EN50192; Volts 208/230; Manufacture Date: 228/00.This is the only informatin I found on the equipment. If you have a video, I am interested of purchasing it, too. Thank you, Dutch

—> Purchase or Repair:
Show More

➡️ Reply