Thermal Dynamics Service & Repair Forum
I have w-Thermal Dynamics plasma cutter that apear to be be bad. The first one is a Pakmaster 50.It has a bad ldd board in the Thermal Dynamics PakMaster 50. Can you repair it? If so, about what does it run?I\'m still trouble shooting the ecno 50 to see what\'s wrong with it.Thank you,Hershel
—> Purchase or Repair:
Reply🗨️Ask a New Question Below❓
Recent Comments Search: "Thermal Dynamics"
- Thermal Dynamics → Collar nut to hold torch cable to machine ↗
- Thermal Dynamics → Thermal Dynamics part for thermal dynamics pax master 50 ↗
- Thermal Dynamics → regulater/filter assembly pakmstr 50 xl thermal dy ↗
- Thermal Dynamics → Thermal Dynamics Thermal dynamics pak master 50xl plus ↗
- Thermal Dynamics → Air no cutting. ↗
- Thermal Dynamics → repair for plasma cutter ↗
- Thermal Dynamics → thermal dynamics pak master 50 ↗
- Thermal Dynamics → Thermal Dynamics 19X836 114X147 ↗
- Thermal Dynamics → pakmaster 50XL ↗
- Thermal Dynamics → OPERATION & REPAIR MANUAL OF PAK MASTER XLPLUS ↗
- Thermal Dynamics → Service Manual for Pak Master 50XL Plus ↗
- Thermal Dynamics → Thermal Dynamics 50 ↗
- Thermal Dynamics → PAK 50 Main Board resistors ↗
If you need your Thermal Dynamics unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110
Recent 14 Comments
I have a Pakmaster that also has a bad board. Maybe we have enough parts to make one good machine.
—> Purchase or Repair:
—> Purchase or Repair:
I have an older oak master 50 the collar that screws on to the machine that holds the cables to the pak master snapped i\'n half is there any were you no of that I can retrieve this part?Thanks michael
—> Purchase or Repair:
—> Purchase or Repair:
hello, we are a art museum plus art school. we have a thermal dynamics pax master 50. we are not able to control or use the gas pressure gauge. we do not have a part number. can you offer us some help. thank you
—> Purchase or Repair:
—> Purchase or Repair:
i have a service manual i have checked it out, toubleshooting points to main board i need estimate on repair of board
—> Purchase or Repair:
—> Purchase or Repair:
Hello There,I was using the above model a couple of days ago when it quit cutting for a moment and then started working again. This happened about three times and on the forth time the air was coming out but just quit cutting altogether.Are there things I can check before having it repaired to make …Purchase or Repair: 
...
Show More
Show More
I am looking for a service manual book for Pak Master Thermal Dynamics 50XL Plus Air Plasma Cutting System. This number is was on the main plate: EN50192; Volts 208/230; Manufacture Date: 228/00.This is the only informatin I found on the equipment. If you have a video, I am interested of purchasing …Purchase or Repair: 
...
Show More
Show More
Machine Error Thermal Dynamics 19X836 114X147 board malfunction. Production halted.
—> Purchase or Repair:
—> Purchase or Repair:
I have a Thermal dynamics pak master 50xl plus I have a part# 9-8010 logic / gate drive pcb board that needs repair can you fix mine? and how much would it cost me?
—> Purchase or Repair:
—> Purchase or Repair:
Can you give me the value of the two large resistors on the main pcb located in R165 & R166 locations. They appear to be around 5 watt in size.
—> Purchase or Repair:
—> Purchase or Repair:
my son knock it off of the stand and fell on the concrete it broke off the regulater/assembly can i get a replacement part.
—> Purchase or Repair:
—> Purchase or Repair:
Show More