Vonweise for Service call 1-336-969-0110 at Industrial Electronics Repair

Vonweise Service & Repair Forum

the chair stop in lay out mode I could hear the motor runing but it would not move the chair to let my mother get out of it thank you wilson

— Posted by herman wilson on 2007-03-22

Reply🗨️Ask a New Question Below❓

If you need your Vonweise unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 66 Comments

#Vonweise by Dave Henderson on 2005-08-10 14:27

I have a VonWeise gear motor model # V02387AB62 serial # D285 that has a cracked gear case casting and I need a replacement. The casting Model # is VW62 and has the part # W2974 on the inside. Is this something you can help me with or advise who could?Thanks,Dave

#Vonweise by Linda Orak on 2005-09-10 22:53

I have a VonWeise motor model L3096 that is used in a lift chair. The motor stopped working. I was wondering how to get a replacement motor. Can you help me? I\'ve tried locally with no luck.Thank you,Linda

#Vonweise by Howard Bassel on 2005-10-18 23:04

Do you supply this type of part or should I go directly to the Company. If you suggest tthat I go to the Comapny, can you supply an e - mail and a phone number.Thank you,Howard Bassel

#Vonweise by bill smaney on 2005-12-08 01:52

where can i get parts for von weise lift chairsmy phone # is 920 829 5094

#Vonweise by Gregg Luebbering on 2006-04-07 20:36

I have a problem with a Power Track Jr. ventilation amchine that you manufacture for Hired Hand of Alabama. How can I see a parts diagram of this and determine the part number I need to repair this unit? Thanks so much for responding back to me.

#Vonweise by Kristine Polzer on 2006-06-27 19:20

I am looking for gearcase cover for a Invacare LC53 Lift chair Serial #97C77045 with a Von Weise Motor.

#Vonweise by Stan Thomas on 2006-11-16 01:57

Lift chair won\'t go down. Checked out and \'lower\' relay is sticking. Tapped with screwdriver and it started working. Relays are soldered to the board... The chair is fairly old and customer doesn\'t want to spend a lot on it...as usual. Please give me an estimate. Thanks, Stan

#Vonweise by Debra Fauvor on 2007-01-02 20:29

I purchased a lift chair from Sears 7 years ago. They used to run a stupid ad campaign \"Buy it at Sears, get it fixed at Sears\". Now they don\'t want to fix a damn thing. Do you know where I can get it fixed?

#Vonweise by melanie hamilton on 2007-03-05 04:43

We don\'t know if the bed controller is faulty or if it\'s the motor unit being controlled. Would appreciate any information you might have regarding which it might be. If we know that it\'s the controller for certain...Numbers on control unit:VWE-PD-M003 (zero zero three)Serial number: 22968

#Vonweise by Chuck Henry on 2007-03-07 04:57

I have a treadmill with a VonWeise V05119AJ76 motor that has a 19:1 gearbox on it. The output screw shaft is bent, but otherwise the unit works fine. Is it possible to get just that replacement part?

#Vonweise by herman wilson on 2007-03-22 06:51

the chair stop in lay out mode I could hear the motor runing but it would not move the chair to let my mother get out of it thank you wilson

#Vonweise by Richard Sieger on 2007-04-24 17:20

I have a VonWeise Gear Motor Model V05679CB76U, Serial B1999 that has stripped the main drive gear. I need to replace it. It\'s the largest gear in the gearbox, which connects to the output shaft? I would also like to purchase a maintenance/repair manual for it, if one is available.

#Vonweise by jessie burns on 2007-06-05 18:50

chair will go up but not down

#Vonweise by victor on 2007-06-20 20:27

I request to quote engines for clinical bedsattevictor

#Vonweise by Kenneth Hoover on 2007-08-01 22:36

Von Weise drive assy. used on Invcare adj. bed(mod#V07564AS76U) will raise and lower the head but when in the low height position ,3 to 6 inches, the drive appears to slip back a couple of inches. Keeps slipping back until you reach acertian point then stops slipping back. When just raiseing and low...
Show More

#Vonweise by Dave Burnham on 2007-08-21 18:24

We have a VonWeise Motor for our Manitowoc Ice Machine. The shaft is broken that turns the auger. The Transmission model number is WW62. Can we get the transmission without the motor or does that come as a complete unit? Please give us a cost and availibility.Thank You!Dave Burnham Tarta1127 W.Centr...
Show More

#Vonweise by Ben Rowden on 2007-09-07 04:33

I lost my remote for this bed and was trying to program a logitech harmony remote to control it. Do you know if this is possible?Ben

#Vonweise by Mary Anderson on 2007-09-28 22:17

Looking for a Von-weise remote to operate an adjustable bed. Any help?Thanks

#Vonweise by norman on 2007-10-15 21:15

Smae problem of not holding it\'s position and the head position slowly sinks back down. It only taked to cotter pins to replace this unit on the bed frame so I would like to find a replacement unit if possible.

#Vonweise by Equarborirurn on 2007-10-30 04:45

Where I can find good quality films?Can anyone help me?

#Vonweise by Paul Priester on 2007-11-12 14:40

Do you have replacment parts for camper jacks

#Vonweise by Aaron Tam on 2007-12-14 12:03

I have a Von Weise gearmotor, inside the gear box, there is a plastic gear assembly driven by the main shaft. The plastic gear is broken.Can you tell me where can i buy the replacement of the plastic (nylon)gear asssembly in Ontario, Canada if posible.Thank you

#Vonweise by benny stuben rauch on 2007-12-20 11:39

I need the two relays or pc board and relays how ever the part comes for a Von Weise lift chair motor model v05679DL76U serial C2800 cell phone (248) 240-3015 or home phone (586) 777-5469

#Vonweise by Ruth Sprouse on 2008-01-11 23:37

Hand control on Vonweise lift chair not working. Chair only works occassionally. Goes up but will not go down. How do I get a replacement hand control, what is the cost for a control and how long is the warrenty?Please call 309-341-3456.Thank you

#Vonweise by jon mitchell on 2008-01-17 04:56

have invacare chair w/ vonweise drive. up/stand works ok, down erratic. have to tap relay to get operation of down/recline. looking for repacement relay board pricing and availability. m# V07647AA76U ID# IDI225IBN0252 OPERATOR#H3100 JJS4000M800 VWE-3 INVACARE CHAIR DCF M#LC86 S#00I953361 115vac 60hz...
Show More

#Vonweise by Mike Baldarelli on 2008-05-12 22:58

We are looking for a new motor or the upper housing which connects the motor to the chair. The model number is: VO5789AD76U - Serial number: HO896The following numbers were also on the motor: K14003-0001 7190-1935 Type - 90B1Please let me know if you could help.Thanks,Mike

#Vonweise by Ron Vocht on 2008-07-29 00:09

I may need a replacement motor for an electric adjustable bed. Where can I find a Von Weise Gear Co. motor, model VO2898AB76 ? It is a thermally protected electric motor. Volts-115, AC, Amps-1.4, Hz-60, Ph-1, Hp-1/10, Ratio-19:1, Serial-E-78, Shaft-7/16. Does this company still exist?

#Vonweise by SUSAN on 2008-09-13 17:56

I AM LOOKING FOR A VON WEISE STEP COVER MOTOR MODEL -14943674, 12VDC 8.7A 24:1 SN-L1407. THIS IS FOR THE STEP COVER IN A NATIONAL RV. IF YOU CAN GIVE ME ANY INFORMATION ON WHERE I CAN LOCATE ONE OF THESE THAT WOULD BE GREAT.THANK YOU

#Vonweise by Anke Hamalian on 2008-09-16 23:31

need to replace this motor.Where I can buy?

#Vonweise by Michael L. Walker on 2008-11-11 23:14

I have a King Koil elect. bed. About year 1981.The wormgear that drives the up and down motion of the bed, has come out of the motor. I can\'t tell what is supposed to keep the end of the wormgear in place in the motor. What I am calling a \"wormgear\" is a long \"geared\" shaft,...
Show More

#Vonweise by HENRY McCUISTION on 2009-03-04 21:35

One way to test whether it is your controller or a motor is to switch the plug from the nonfunctioning section (Head, Foot or Bed) into the recepticle for one of the working sections, then use that control button to test the motor itself. Example: If the head does not work but the foot does, unplug ...
Show More

#Vonweise by Jim on 2009-03-23 17:56

Hi, Need switch for handheld controller. Have one ?? How much ?? Also, service manual ?? Thanks, Jim

#Vonweise by Brad Gooch on 2009-03-30 15:08

I am working an an Invacare lift chair with a Vonweise drive mechanism. When I press the button on the hand control the actuator will run one direction but not the other. I have tried a different hand control (pendant) and I get the same result. When I push the button to go the other direction I hea...
Show More

#Vonweise by Gary Marsalis on 2009-04-07 23:49

I have a Cleavland Lift Chair with a Von Weise Model Number V07647AA76U Serl. Number K3000,115VAC, Ratio: 169:1 gear motor/actuator. I need the power cord with plug that plugs into the motor control. The plug is white plastic with the female pins in it, it mates to a plug in the control that has two...
Show More

#Vonweise by Rob on 2009-04-09 19:14

I have a patient with a lift chair that will move in the up position but willnot move in the down position. i am assuming that it is the remote and not the motor. the model Number is :v05679dl76the ID # is ID84072n0073Serial # JJ54000m800The patient uses the chair for sleeping and requires the chair...
Show More

#Vonweise by neal on 2009-06-27 14:49

the drive gear is all broken up in my lift chair could you please help me. i am trying to take the gear out but there is a pin that runs threw the drive gear how can i take the pin out i would like to see a diagram if you have one thank you neal

#Vonweise by OblilkFib on 2009-07-22 20:46

Hi friend i am new to this. Just thought that i would say hello to everyone! dont really know what else to say.I love texting, nothing else to say so bye

#Vonweise by gerald laws on 2009-08-13 01:35

hello the mane gear that makes the chair go up and down is striped out it is a plastis gear on top of the motor that connects to the input shaft what do i need to do to get the gear or have you fix it please resboun thank you and god bless geraldlaws@bellsouth.net

#Vonweise by Peter Winter on 2010-01-15 00:17

I am hoping that you will be able to either supply, or tell me where I might be able to locate a replacement for Von Weise gearmotor, Model #V 056 79CB76U, 115 VAC 60 Hz, 1.0 AVWE-1 Ratio 169: 1This is a motor from a lift chair manufactured by the Cleveland Chair Company which is no longer in existe...
Show More

#Vonweise by Peter Winter on 2010-01-15 00:30

I am hoping that you will be able to either supply, or tell me where I might be able to locate a replacement for Von Weise gearmotor, Model #V 056 79CB76U, 115 VAC 60 Hz, 1.0 AVWE-1 Ratio 169: 1This is a motor from a lift chair manufactured by the Cleveland Chair Company which is no longer in existe...
Show More

#Vonweise by Larry Taylor on 2010-03-13 22:38

Switching the wires in hand contoller to raise then switch wires again to lower chair. I believe the switch in the hand controller is bad and needs to be replaced. The motor works ok.

#Vonweise by Jodi Tolbert on 2010-07-29 15:24

I need a new control cord for model V00562BF76U, type 90B1 adjustable bed by LeggettThe cord looks like a phone cord

#Vonweise by Ron Kadesch on 2010-08-23 03:39

I need a working or parts for a Von Weise lift chair operator # 908. Some other # on case- Model VO7647AA76U, also VWE-3 DCF. The motor runs, but the lift shaft does\'t move. I think the nut or drive shaft must be striped. Can anyone help with parts or info??? THANKS, Ron

#Vonweise by unangeRomonab on 2010-09-01 03:23

MARGARITA TRICIA d and down-to-earth Tyler Perry DEMETRICE

#Vonweise by Robert Anderson on 2010-10-23 19:12

Do you have something that will replace my two von weise gear boxs & motors? Motors still work but the gear boxes and surrounding parts (woodruff key) et all have given up... Need 2 \"assembled gear motors with cable if possilbeModel number - V02647AC76 (MF-05) 1/12 HP 1.4 AMP 19:1 RATIO YE...
Show More

#Vonweise by THELMA on 2011-01-10 02:56

MY MOTOR DON\'T WORK SAME MODEL AS YOURS.DID YOU FIND ANY PARTS?OR EVEN ANOTHER MOTOR?I\'M LOOKING TOO.PLEASE LET ME KNOW.

#Vonweise by millie hinojosa on 2011-02-24 02:15

I need the remote control power cord for lift chair serial number L0201. model v07647aa76u

#Vonweise by leon pemberton on 2011-03-19 15:43

i need a drive gear set fore m.vo5679dl76u s.c2700 chair

#Vonweise by Gary Abbott on 2011-03-19 20:25

Vonweise model # v00310araa needs new seal, bearing and refilled with gear oil

#Vonweise by Steve Webb on 2011-08-04 02:04

Can I get a replacement motor, if so how much will it cost.Model# V05679DL76UID# ID10724NO117Serial # D1700 JJ54000MP00Made by Fasco CompanyCall me at 210-416-7789

#Vonweise by Ken Bensinger on 2011-10-11 00:36

I may need a replacement motor for an electric adjustable bed. Where can I find a Von Weise Gear Co. motor, model VO2898AB76 ? The motor is working but the gear box is bad.It has a broken flat bearing and a broken washer in it. it also has a stipped plastic gear.

#Vonweise by Paul Bowers on 2011-10-12 02:28

The bolt holes broke out on the head end. I need a new head cover.

#Vonweise by Hector Juarez on 2012-02-24 00:00

VonWeise V0574 not powering on at all. Need urgent repair service.

#Vonweise by gregg on 2012-07-06 20:36

need to find a wireless remote for an adjustable bed. bed has von weise motors with massage motors, model number V07594AB79U.Trancemitter box model number 3433. frequancy 433 mhz rev1.1 . Any help please.

#Vonweise by Lynda Dobbin-Turner on 2013-03-11 00:53

We have a Restonic adjustable bed, with the above serial number on the body of the control system, but the controls were lost in a move. Need to find a replacement. Suggestions?

#Vonweise by Alice Hanna on 2013-10-01 23:55

I am looking for a replacement motor for an electric bed. Model #V05789AG76U Serial # H2997 P/N 7190-1935 type 9081can you supply me with one or tell me where I can find one.

#Vonweise by Arnold on 2013-11-01 17:52

I have a vo5679cb76u and the electric board is burned

#Vonweise by Rich Angel on 2013-11-07 21:37

I have an adjustable bed that appears to have your motor/actuator. The model on the motor is VO7564AS76U. The connecting ring located on the top of the motor has broken and I would like to purchase a new one. Hopefully you can sell/provide that top piece but if I need to purchase the motor and assem...
Show More

#Vonweise by mike hetherington on 2014-01-25 20:52

I need the controller for my adjustable bed. The only label I can find is on the motor and it has # V07564AS76U. The name is difficult to see but it looks like \"Dunntron\" Thanks

#Vonweise by Randy Robinson on 2014-03-21 18:19

I would like to know if I can purchase parts for the chair actuator that I am repairing? The large gear that is attached to the screw need to be replaced. The model #v05679dl76u ser #g1000. If not can you direct me to somone that handles the parts for these units. Thank you Randy

#Vonweise by Rob Johnson on 2014-12-03 00:30

Having the exact same problem with chair here also. Has anyone found out how to fix this???

#Vonweise by Maria Bartolotta on 2017-05-10 18:32

I have two twin ajustable beds...together as a king-size.One bed is no longer adjustable. Is there someone in my location that does repairs for this bed?Model: V07564AS76U115 VAC 60 HZ 2.8AClass B INSUL 40*CThermally protectedSerial F2101MO100150VWG-71E32557

#Vonweise by Jerry Landseadel on 2017-11-25 21:44

I have a lift chair made by Golden Technologies, INC. with a VonWeise lift mechanism, model number v05789AD76U, serial number A1497, 115 vac, 60 HZ 1.6 A. The chair is in excellent shape but the mechanism broke. I need a new part.

#Vonweise by Tammy McAdams on 2019-02-06 14:44

Do you know how to obtain a replacement remote for a Vonweise bed? It's on older model, Model # VO0562BF76U.Thanks so much

#Vonweise by Jo_Anne Guigue on 2021-02-27 18:46

the model V07508AW76U Serial A0902 I found these information on the motor I need the remote . How much is the remote. I live in Canada

#Vonweise by Chetan on 2021-09-07 23:14

Need to fix bed the motor want come on need new control

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.