Troubleshooting Vonweise: Common problems and repair info

Vonweise for Service call 1-336-969-0110 at Industrial Electronics Repair

Vonweise Service & Repair Forum

I have a VonWeise gear motor model # V02387AB62 serial # D285 that has a cracked gear case casting and I need a replacement. The casting Model # is VW62 and has the part # W2974 on the inside. Is this something you can help me with or advise who could?Thanks,Dave

—> Purchase or Repair:

— Posted by Dave Henderson on 2005-08-10

Reply🗨️Ask a New Question Below❓

Recent 67 Comments

#Vonweise by norman on 2007-10-15 21:15

Smae problem of not holding it\'s position and the head position slowly sinks back down. It only taked to cotter pins to replace this unit on the bed frame so I would like to find a replacement unit if possible.

—> Purchase or Repair:

➡️ Reply

#Vonweise by melanie hamilton on 2007-03-05 04:43

We don\'t know if the bed controller is faulty or if it\'s the motor unit being controlled. Would appreciate any information you might have regarding which it might be. If we know that it\'s the controller for certain...Numbers on control unit:VWE-PD-M003 (zero zero three)Serial number: 22968—> …Purchase or Repair:

➡️ Reply

#Vonweise by Michael L. Walker on 2008-11-11 23:14

I have a King Koil elect. bed. About year 1981.The wormgear that drives the up and down motion of the bed, has come out of the motor. I can\'t tell what is supposed to keep the end of the wormgear in place in the motor. What I am calling a \"wormgear\" is a long \"geared\" shaft, about 1/2 in in dia…Purchase or Repair:

➡️ Reply

#Vonweise by Rob on 2009-04-09 19:14

I have a patient with a lift chair that will move in the up position but willnot move in the down position. i am assuming that it is the remote and not the motor. the model Number is :v05679dl76the ID # is ID84072n0073Serial # JJ54000m800The patient uses the chair for sleeping and requires the chair…Purchase or Repair:

➡️ Reply

#Vonweise by Howard Bassel on 2005-10-18 23:04

Do you supply this type of part or should I go directly to the Company. If you suggest tthat I go to the Comapny, can you supply an e - mail and a phone number.Thank you,Howard Bassel

—> Purchase or Repair:

➡️ Reply

#Vonweise by Mary Anderson on 2007-09-28 22:17

Looking for a Von-weise remote to operate an adjustable bed. Any help?Thanks

—> Purchase or Repair:

➡️ Reply

#Vonweise by Gary Abbott on 2011-03-19 20:25

Vonweise model # v00310araa needs new seal, bearing and refilled with gear oil

—> Purchase or Repair:

➡️ Reply

#Vonweise by Aaron Tam on 2007-12-14 12:03

I have a Von Weise gearmotor, inside the gear box, there is a plastic gear assembly driven by the main shaft. The plastic gear is broken.Can you tell me where can i buy the replacement of the plastic (nylon)gear asssembly in Ontario, Canada if posible.Thank you

—> Purchase or Repair:

➡️ Reply

#Vonweise by bill smaney on 2005-12-08 01:52

where can i get parts for von weise lift chairsmy phone # is 920 829 5094

—> Purchase or Repair:

➡️ Reply

#Vonweise by Ron Kadesch on 2010-08-23 03:39

I need a working or parts for a Von Weise lift chair operator # 908. Some other # on case- Model VO7647AA76U, also VWE-3 DCF. The motor runs, but the lift shaft does\'t move. I think the nut or drive shaft must be striped. Can anyone help with parts or info??? THANKS, Ron

—> Purchase or Repair:

➡️ Reply

#Vonweise by Kristine Polzer on 2006-06-27 19:20

I am looking for gearcase cover for a Invacare LC53 Lift chair Serial #97C77045 with a Von Weise Motor.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Rob Johnson on 2014-12-03 00:30

Having the exact same problem with chair here also. Has anyone found out how to fix this???

—> Purchase or Repair:

➡️ Reply

#Vonweise by Lynda Dobbin-Turner on 2013-03-11 00:53

We have a Restonic adjustable bed, with the above serial number on the body of the control system, but the controls were lost in a move. Need to find a replacement. Suggestions?

—> Purchase or Repair:

➡️ Reply

#Vonweise by Mike Baldarelli on 2008-05-12 22:58

We are looking for a new motor or the upper housing which connects the motor to the chair. The model number is: VO5789AD76U - Serial number: HO896The following numbers were also on the motor: K14003-0001 7190-1935 Type - 90B1Please let me know if you could help.Thanks,Mike

—> Purchase or Repair:

➡️ Reply

#Vonweise by Debra Fauvor on 2007-01-02 20:29

I purchased a lift chair from Sears 7 years ago. They used to run a stupid ad campaign \"Buy it at Sears, get it fixed at Sears\". Now they don\'t want to fix a damn thing. Do you know where I can get it fixed?

—> Purchase or Repair:

➡️ Reply

#Vonweise by Ben Rowden on 2007-09-07 04:33

I lost my remote for this bed and was trying to program a logitech harmony remote to control it. Do you know if this is possible?Ben

—> Purchase or Repair:

➡️ Reply

#Vonweise by mike hetherington on 2014-01-25 20:52

I need the controller for my adjustable bed. The only label I can find is on the motor and it has # V07564AS76U. The name is difficult to see but it looks like \"Dunntron\" Thanks

—> Purchase or Repair:

➡️ Reply

#Vonweise by Chuck Henry on 2007-03-07 04:57

I have a treadmill with a VonWeise V05119AJ76 motor that has a 19:1 gearbox on it. The output screw shaft is bent, but otherwise the unit works fine. Is it possible to get just that replacement part?

—> Purchase or Repair:

➡️ Reply

#Vonweise by millie hinojosa on 2011-02-24 02:15

I need the remote control power cord for lift chair serial number L0201. model v07647aa76u

—> Purchase or Repair:

➡️ Reply

#Vonweise by unangeRomonab on 2010-09-01 03:23

MARGARITA TRICIA d and down-to-earth Tyler Perry DEMETRICE

—> Purchase or Repair:

➡️ Reply

#Vonweise by Rich Angel on 2013-11-07 21:37

I have an adjustable bed that appears to have your motor/actuator. The model on the motor is VO7564AS76U. The connecting ring located on the top of the motor has broken and I would like to purchase a new one. Hopefully you can sell/provide that top piece but if I need to purchase the motor and assem…Purchase or Repair:

➡️ Reply

#Vonweise by leon pemberton on 2011-03-19 15:43

i need a drive gear set fore m.vo5679dl76u s.c2700 chair

—> Purchase or Repair:

➡️ Reply

#Vonweise by Maria Bartolotta on 2017-05-10 18:32

I have two twin ajustable beds...together as a king-size.One bed is no longer adjustable. Is there someone in my location that does repairs for this bed?Model: V07564AS76U115 VAC 60 HZ 2.8AClass B INSUL 40*CThermally protectedSerial F2101MO100150VWG-71E32557

—> Purchase or Repair:

➡️ Reply

#Vonweise by Rebecca on 2025-05-01 23:04

We need a replacement remote control for a VonWeise adjustable mattress purchased back in 2001. V00562BF76U

—> Purchase or Repair:

➡️ Reply

#Vonweise by jon mitchell on 2008-01-17 04:56

have invacare chair w/ vonweise drive. up/stand works ok, down erratic. have to tap relay to get operation of down/recline. looking for repacement relay board pricing and availability. m# V07647AA76U ID# IDI225IBN0252 OPERATOR#H3100 JJS4000M800 VWE-3 INVACARE CHAIR DCF M#LC86 S#00I953361 115vac 60hz…Purchase or Repair:

➡️ Reply

#Vonweise by Tammy McAdams on 2019-02-06 14:44

Do you know how to obtain a replacement remote for a Vonweise bed? It's on older model, Model # VO0562BF76U.Thanks so much

—> Purchase or Repair:

➡️ Reply

#Vonweise by herman wilson on 2007-03-22 06:51

the chair stop in lay out mode I could hear the motor runing but it would not move the chair to let my mother get out of it thank you wilson

—> Purchase or Repair:

➡️ Reply

#Vonweise by victor on 2007-06-20 20:27

I request to quote engines for clinical bedsattevictor

—> Purchase or Repair:

➡️ Reply

#Vonweise by Dave Burnham on 2007-08-21 18:24

We have a VonWeise Motor for our Manitowoc Ice Machine. The shaft is broken that turns the auger. The Transmission model number is WW62. Can we get the transmission without the motor or does that come as a complete unit? Please give us a cost and availibility.Thank You!Dave Burnham Tarta1127 W.Centr…Purchase or Repair:

➡️ Reply

#Vonweise by Kenneth Hoover on 2007-08-01 22:36

Von Weise drive assy. used on Invcare adj. bed(mod#V07564AS76U) will raise and lower the head but when in the low height position ,3 to 6 inches, the drive appears to slip back a couple of inches. Keeps slipping back until you reach acertian point then stops slipping back. When just raiseing and low…Purchase or Repair:

➡️ Reply

#Vonweise by Larry Taylor on 2010-03-13 22:38

Switching the wires in hand contoller to raise then switch wires again to lower chair. I believe the switch in the hand controller is bad and needs to be replaced. The motor works ok.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Jodi Tolbert on 2010-07-29 15:24

I need a new control cord for model V00562BF76U, type 90B1 adjustable bed by LeggettThe cord looks like a phone cord

—> Purchase or Repair:

➡️ Reply

#Vonweise by Jim on 2009-03-23 17:56

Hi, Need switch for handheld controller. Have one ?? How much ?? Also, service manual ?? Thanks, Jim

—> Purchase or Repair:

➡️ Reply

#Vonweise by Steve Webb on 2011-08-04 02:04

Can I get a replacement motor, if so how much will it cost.Model# V05679DL76UID# ID10724NO117Serial # D1700 JJ54000MP00Made by Fasco CompanyCall me at 210-416-7789

—> Purchase or Repair:

➡️ Reply

#Vonweise by gregg on 2012-07-06 20:36

need to find a wireless remote for an adjustable bed. bed has von weise motors with massage motors, model number V07594AB79U.Trancemitter box model number 3433. frequancy 433 mhz rev1.1 . Any help please.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Hector Juarez on 2012-02-24 00:00

VonWeise V0574 not powering on at all. Need urgent repair service.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Richard Sieger on 2007-04-24 17:20

I have a VonWeise Gear Motor Model V05679CB76U, Serial B1999 that has stripped the main drive gear. I need to replace it. It\'s the largest gear in the gearbox, which connects to the output shaft? I would also like to purchase a maintenance/repair manual for it, if one is available.—> …Purchase or Repair:

➡️ Reply

#Vonweise by OblilkFib on 2009-07-22 20:46

Hi friend i am new to this. Just thought that i would say hello to everyone! dont really know what else to say.I love texting, nothing else to say so bye

—> Purchase or Repair:

➡️ Reply

#Vonweise by Jerry Landseadel on 2017-11-25 21:44

I have a lift chair made by Golden Technologies, INC. with a VonWeise lift mechanism, model number v05789AD76U, serial number A1497, 115 vac, 60 HZ 1.6 A. The chair is in excellent shape but the mechanism broke. I need a new part.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Gregg Luebbering on 2006-04-07 20:36

I have a problem with a Power Track Jr. ventilation amchine that you manufacture for Hired Hand of Alabama. How can I see a parts diagram of this and determine the part number I need to repair this unit? Thanks so much for responding back to me.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Jo_Anne Guigue on 2021-02-27 18:46

the model V07508AW76U Serial A0902 I found these information on the motor I need the remote . How much is the remote. I live in Canada

—> Purchase or Repair:

➡️ Reply

#Vonweise by Equarborirurn on 2007-10-30 04:45

Where I can find good quality films?Can anyone help me?

—> Purchase or Repair:

➡️ Reply

#Vonweise by Gary Marsalis on 2009-04-07 23:49

I have a Cleavland Lift Chair with a Von Weise Model Number V07647AA76U Serl. Number K3000,115VAC, Ratio: 169:1 gear motor/actuator. I need the power cord with plug that plugs into the motor control. The plug is white plastic with the female pins in it, it mates to a plug in the control that has two…Purchase or Repair:

➡️ Reply

#Vonweise by Anke Hamalian on 2008-09-16 23:31

need to replace this motor.Where I can buy?

—> Purchase or Repair:

➡️ Reply

#Vonweise by Ken Bensinger on 2011-10-11 00:36

I may need a replacement motor for an electric adjustable bed. Where can I find a Von Weise Gear Co. motor, model VO2898AB76 ? The motor is working but the gear box is bad.It has a broken flat bearing and a broken washer in it. it also has a stipped plastic gear.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Ruth Sprouse on 2008-01-11 23:37

Hand control on Vonweise lift chair not working. Chair only works occassionally. Goes up but will not go down. How do I get a replacement hand control, what is the cost for a control and how long is the warrenty?Please call 309-341-3456.Thank you

—> Purchase or Repair:

➡️ Reply

#Vonweise by Paul Bowers on 2011-10-12 02:28

The bolt holes broke out on the head end. I need a new head cover.

—> Purchase or Repair:

➡️ Reply

#Vonweise by Linda Orak on 2005-09-10 22:53

I have a VonWeise motor model L3096 that is used in a lift chair. The motor stopped working. I was wondering how to get a replacement motor. Can you help me? I\'ve tried locally with no luck.Thank you,Linda

—> Purchase or Repair:

➡️ Reply

#Vonweise by Peter Winter on 2010-01-15 00:30

I am hoping that you will be able to either supply, or tell me where I might be able to locate a replacement for Von Weise gearmotor, Model #V 056 79CB76U, 115 VAC 60 Hz, 1.0 AVWE-1 Ratio 169: 1This is a motor from a lift chair manufactured by the Cleveland Chair Company which is no longer in existe…Purchase or Repair:

➡️ Reply

#Vonweise by Randy Robinson on 2014-03-21 18:19

I would like to know if I can purchase parts for the chair actuator that I am repairing? The large gear that is attached to the screw need to be replaced. The model #v05679dl76u ser #g1000. If not can you direct me to somone that handles the parts for these units. Thank you Randy—> …Purchase or Repair:

➡️ Reply

Vonweise Service & Repair Forum

Reply🗨️Ask a New Question Below❓

Recent 67 Comments

Contact Us

🚑Shop Location🛠️

📞Phone

📦Mailing Address🚛