Rittenhouse Service & Repair Forum

I HAVE A RITTENHOUSE INTERCOM AM/FM SYSTEM , MODEL # 9042 AND I AM TRYING TO FIND OUT WHAT SIZE[POWER REQUIREMENT] TRANSFORMER [ 4 WIRE] I NEED. I DO NOT HAVE THE OLD ONE. ANY HELP WOULD BE APPRECIATED. THANKS

β€”> Purchase or Repair: Ticket Image

β€” Posted by GARY KASPRZYK on 2007-12-26

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by Glenn Loiselle on 2012-08-09 11:51
I have a circa 1977 Artolier Lighting and Sound door Chimes / door bell / wall clock that HUMMS all the time. MODEL # C8633Can it be repaired?

β€”> Purchase or Repair:
#Rittenhouse by James Short on 2013-02-24 20:40
A plunger on my 50 year old door chime is not returning to the rest position when the door chime is not activated. The consequence is a continuous buzz and erratic operation when the button is pressed.Have I provided sufficient information to diagnose the ease of repair?Thank you.Jimβ€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Terri McDougall on 2012-04-06 14:55
Our house was built in 1978 and we purchased it in 1997. It had the Rittenhouse monitor system in place with the main unit in the kitchen and smaller units scattered thought the house and in an attached apartment. The unit has never worked since we have been here and I was wondering if it is repaira…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Cyndi Taylor Krier on 2010-11-17 22:19
Can I order a replacement transformer for this doorbell from you?

β€”> Purchase or Repair:
#Rittenhouse by Mark Danko on 2015-09-10 19:17
Hi, need repair to this unit, sound cuts in and out when volume control knob is turned/wiggled. Moving molex 5 pin connector on circuit board also causes power to cut in and out. Mode delector knob has become stiff to operate. Please send estimate if repair is possible, thanks

β€”> Purchase or Repair:
#Rittenhouse by Paul Winchock on 2018-10-15 21:41
I have a Rittenhouse 550, 551 doorbell chime.The unit itself works fine. What I am missing (which someone was supposed to nor trash) is the transformer that sequences the chimes. Do you have a transformer for this that will work? And if so, obviously, what would one cost?Thank you for taking the tim…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by mike boccio on 2015-08-28 16:39
hi I have a m7034 intercome system.The out door speak into box was flooded by our sandy storm.Needs to be replaced.The wiring is good and it would be easy to replace if I had original replacement kit. thank you mike

β€”> Purchase or Repair:
#Rittenhouse by Morris Hoagland on 2014-01-05 03:53
My Rittenhouse Master unit has failed. Is there a replacement unit I can purchase?

β€”> Purchase or Repair:
#Rittenhouse by Glenn Loiselle on 2012-08-09 11:58
I have a circa 1977 Artolier Lighting and Sound door Chimes / door bell / wall clock that HUMMS all the time. MODEL # C8633Can it be repaired?

β€”> Purchase or Repair:
#Rittenhouse by Albert M. Brien on 2012-07-29 04:52
I have an older system, it was still working but when a water pipe broke behind my kitchen wall, it soaked the unit and ruined it. I want to know how much it would cost to have it replaced so I can get back the intercom and music function. Thank youAlbert Brien

β€”> Purchase or Repair:
#Rittenhouse by Bernard Zeifang on 2014-02-18 15:19
Please provide information needed to ship my unit to you for repair estimateand possible repair.I am assuming you need only the radio(master unit).Thank you!

β€”> Purchase or Repair:
#Rittenhouse by GENE LAYNE on 2016-07-28 12:11
Can you advise if a Emerson Rittenhouse RC 577 Doorbell mechanical chime will work with a 24V Transformer?I have a 16V and wanted to add a camera to this?ThanksGene 732-754-1205I cannot locate a manual im guessing this was made in the 70\'s

β€”> Purchase or Repair:
#Rittenhouse by Jessica Memmott on 2010-07-22 18:45
My model 552 is not working. Licensed Electrician checked it out and it need replacement parts. I want to keep actual doorbell, because of sentimental reasons.

β€”> Purchase or Repair:
#Rittenhouse by sheila on 2011-09-05 18:24
Would you know where i can find a C8931R?

β€”> Purchase or Repair:
#Rittenhouse by Doug Wood on 2009-04-27 20:03
Buying a condo with an inoperative Rittenhouse Model 7021 intercom system. Was constructed in late 70s. Is the technology so out of date that it is not worth restoring? Should I consider restoring the unit, about how much am I looking at? Is there a dealer here in AR, or do I have to ship it to you …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by DANNY on 2010-05-06 16:48
I AM A ELECTRICAL CONTRACTOR AND HAVE BEEN TOLD THAT NUTONE WILL WORK USING EXISTING WIRING THE PROBLEM IS NUTONE WILL NOT WARRANTY IF YOU DO NOT USE NUTONE WIRE, BUT THEY DO HAVE A 30 DAY RETURN POLICY TRY THE SYSTEM IF IT DOES NOT WORK TAKE IT BACK ASAP

β€”> Purchase or Repair:
#Rittenhouse by Francis Roberts on 2007-05-24 22:32
Need new springs for the hammers. This is an old door bell and it has lasted about 40 years. The new ones are sick. This is the best I have heard and would like to keep it another 40 years.

β€”> Purchase or Repair:
#Rittenhouse by Melvin Chrisman on 2007-02-24 22:05
I have a radio intercom unit that needs to be updated.

β€”> Purchase or Repair:
#Rittenhouse by Mary Anne Fuscaldo on 2009-12-25 23:04
I moved this door chime/clock when it was working from one home to another. The electrician that hooked it up did not do it correctly and I have no schematic for how it should be wired. I know it needs three wires but not sure on which of the 7 screws they get wired to. They do not indicate Com or T…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by radu munteanu on 2022-04-20 17:35
Good day, I would need the wiring diagram for a Rittenhouse Clock Model 631/632. Just saved the clock from our old house before remodel and we want to install it back with a running clock and the chime.Thank youRadu 650-450-4806

β€”> Purchase or Repair:
#Rittenhouse by Delia Castillo on 2008-07-29 03:14
we bought this house with installed system. not working. power source not found.

β€”> Purchase or Repair:
#Rittenhouse by Richard Greene on 2008-12-30 17:19
I own a late 60\'s Emerson Rittenhouse Model RC633 door bell Chime.The clock works fine but the door bell doesn\'t.I believe there is a problem with the motor.Can I have this unit repaired and approximately the cost?

β€”> Purchase or Repair:
#Rittenhouse by Jorge Crespo on 2015-05-11 04:05
Riitenhouse chime model C8538R to connect into the AC adapter 16 volt .

β€”> Purchase or Repair:
#Rittenhouse by patrick stark on 2013-12-05 15:48
need wiring, replacement parts and pic of the model noted above. front door pushbutton lights, but no response from chime unit. the backdoor is working normal one chime. What may be wrong? the unit has a selector switch to scroll thru various chimes.

β€”> Purchase or Repair:
#Rittenhouse by Ray G. Brubaker on 2017-09-11 14:32
I have a model Rittenhouse # E780DC door bell push button. The center plastic button is broken. I need a replacement . I can use the whole assemblyPlease email me as to where I can buy it. Thank you.

β€”> Purchase or Repair:
#Rittenhouse by GARY KASPRZYK on 2007-12-26 16:12
I HAVE A RITTENHOUSE INTERCOM AM/FM SYSTEM , MODEL # 9042 AND I AM TRYING TO FIND OUT WHAT SIZE[POWER REQUIREMENT] TRANSFORMER [ 4 WIRE] I NEED. I DO NOT HAVE THE OLD ONE. ANY HELP WOULD BE APPRECIATED. THANKS

β€”> Purchase or Repair:
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

β€”> Purchase or Repair:
#Rittenhouse by Charles Cheshire on 2018-07-13 22:04
Cannot reset time seems stripped.Only two of the chimes work.Where are you physically located.ROUGH repair cost.

β€”> Purchase or Repair:
#Rittenhouse by Richard Burnham on 2021-03-28 21:10
Front and back door bells. I need a diagram showing how to connect the wires from the doorbells. Front works with one wire from Front doorbell going to Terminal B and the other going to Front in the 16 VAC group. I assumed one wire would go from Back doorbell to Terminal A and the other to Back in t…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Gregory Luchey on 2017-03-26 21:44
Door Bell repair motor needed

β€”> Purchase or Repair:
#Rittenhouse by Tedd Boomershine on 2012-04-22 21:49
The clock works fine. Three of the door chimes work, but the fourth and fifth strikers do not work. Do you repair and or have parts to recondition? Thanks, Tedd

β€”> Purchase or Repair:
#Rittenhouse by Frank Giudice on 2009-10-23 16:36
I have a clock and doorchimes door bell model RC-633.I would like to get relacement part for the door bell part the clock is still working.Can you help me

β€”> Purchase or Repair:
#Rittenhouse by Jeffrey on 2008-11-22 22:27
This problem may be caused by a lighted doorbell. After the bell is wrung, the light will re-illuminate. When that happens it may be drawing just enough power to make the door chimes think that the button was pressed once again. This is a repeating pattern.If a lighted door button is used, the solut…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Ejschreier@hotmail.com on 2015-03-25 11:15
Lost during remodeling.

β€”> Purchase or Repair:
#Rittenhouse by IRA G NICHOLS on 2025-07-08 20:58
I have a rittenhouse model c8204 that stopped working, had been working for years. New outside doorbell installed my be the cause.Can I test the bell by shorting the two screw terminals on the rittenhouse inside unit.

β€”> Purchase or Repair:
#Rittenhouse by Paul Gilbert on 2016-06-07 01:02
Need to replace existing bell system with new Paul gilbert

β€”> Purchase or Repair:
#Rittenhouse by Colleen Wilkowski on 2011-04-28 15:24
I am searching for a User Manual for the Rittenhouse M9041 AM/FM Radio-Intercom system. The unit is original to the house built in 1982. I have found a tech manual with schematics but now need to locate a User Manual. Any suggestions would be appreciated. Thanks.

β€”> Purchase or Repair:
#Rittenhouse by sonny sadler on 2011-11-21 16:12
i would like to have an updated model the one i have was installed in 1977 it makes noise, drifts off stations all controls are noisey and sound is garbled. can you tell me where to get help.

β€”> Purchase or Repair:
#Rittenhouse by tom roegner on 2008-09-26 22:07
Eight chime unit {552} repeats sequence continually until switch is disconnected. Switch has been replaced but problem continues----any ideas and is it repairable.....

β€”> Purchase or Repair:
#Rittenhouse by Fred on 2011-05-25 04:18
Art - did you get a reply in answer to your post?I am about to restore the same door chime, you may have info that can help.ThanksFred...

β€”> Purchase or Repair:
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by dan mazzola on 2017-02-17 16:32
need a sequence timer for a emerson rittenhouse model # 632 631

β€”> Purchase or Repair:
#Rittenhouse by Rick Martin on 2015-07-19 07:20
The Rittenhouse C8578-1 135-7351-01 door chime unit caused downtime today from 930 AM to 1145 AM, impacting our operations. Need quick resolution before the next shift. Thank you.

β€”> Purchase or Repair:
#Rittenhouse by Mark Hefner on 2013-03-03 02:30
i am looking to replace my intercom system and looking for a new system to replace it with.

β€”> Purchase or Repair:
#Rittenhouse by TR on 2007-10-27 18:13
I have a Rittenhouse intercom system that was installed in the 60\'s that worked fine until recently. Everything still works fine except the main intercom/control unit. Is there a replacement unit I can buy that I can use with all my existing speakers, etc throughout the house? Even a unit that only…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Paul E. Nelson on 2009-01-19 18:06
Our house came with this intercom system. Very Old I suspect. Is there anyone who could furnish me with a copy of the ownual\'s manual-instructions? Paul

β€”> Purchase or Repair:
#Rittenhouse by charles thomas on 2011-09-14 17:53
I need to purchase a new door bell system comparable with the existing system. I have a one unit on the main level and the other in the basement. The Model number of the existing system is C8203 16 volts AC. I need both units to include outside switch. Also where are the transformers located for thi…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by paul najarian on 2011-08-11 21:58
We\'ve got an old aprox. 30years old unit. signal fades in and out. Best to try and repair or do you sell new/updated maybe with cd or mp3 imputs? Also need a external outdoor speaker/intercom box. Has the 5 plug cupling. thanks,Paul

β€”> Purchase or Repair:
#Rittenhouse by Alex Gracia on 2009-11-13 05:30
I\'M A ROOFING CONTRACTOR IN HOUSTON. WHILE WORKING ON A PROJECT WE BROKE SOME INTERCOM SPEAKER BOXES AND I RPLACE THEM. I WOULD LIKE TO IF SELL THESE INTERCOM SPEAKERS.

β€”> Purchase or Repair:
#Rittenhouse by Marie Gunderman on 2007-11-26 01:41
We purchased our present home in 1998. It was custom built in 1983 with many upgrades that were available at that time. Unfortunately since we have lived here the system does not work. The main unit is 17\' wide and 9\" tall. There are 12 units scattered throughout the house. They each measure 7.5\"…Purchase or Repair: Ticket Image...
Show More

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.