Rittenhouse Service & Repair Forum

I have a Sears Solid State Am-FM Master Station Radio/Intercom Model 113.35150 built by Emerson Electric. Can you repair this station. Please advise/

—> Purchase or Repair: Ticket Image

— Posted by Tobie Ross on 2018-04-13

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by tom roegner on 2008-09-26 22:07
Eight chime unit {552} repeats sequence continually until switch is disconnected. Switch has been replaced but problem continues----any ideas and is it repairable.....

—> Purchase or Repair:
#Rittenhouse by matt arendt on 2009-02-08 18:51
need troubleshooting info on rittenhouse model m7900 amp ser# 3060-0074-2091. also, price and availability of parts as i am working on an intercom system in a 8 unit condo.

—> Purchase or Repair:
#Rittenhouse by Dave Spieker on 2017-11-06 22:05
I am looking for a Rittenhouse Chime Receiver Model C8931R. Would you have one available for purchase or can you direct me to a person or another company that may have one available. Thank you!

—> Purchase or Repair:
#Rittenhouse by Roshan on 2011-04-18 18:17
I have an old Rittenhouse intercome unit, since I don\'t use it that much, I would like to replace the face of it with something newer, don\'t know if it;s possiable? please let me know how i can do this.

—> Purchase or Repair:
#Rittenhouse by dave walters on 2008-10-24 14:59
Just wondering i have a rittenhouse system rcm-1 and the intercom system part does not seem to be working. We can broadcast for the main unit and it is heard in the other units but when we try to broadcast from one of the other units to the main you can not hear the person ? Anysuggestions or do you…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Richard Gilbert on 2014-03-13 02:02
Looking to replace the outside door bell speaker Mod. No.M9305

—> Purchase or Repair:
#Rittenhouse by Jamie Wingler on 2009-08-30 05:41
I have an inoperative Rittenhouse Model 7021 intercom system as well. Can I fix it or do I have to buy new?

—> Purchase or Repair:
#Rittenhouse by Qaiser Baig on 2012-07-01 04:25
Hi,Some one open the wires of my door bell Model C8550 (in the bell). Would you please give the wiring/connection diagram for this door bell so that I can re-connect the wire to operate my door bell.You co-operation & early response will be highly appreciated.Regards,Qaiser Baig—> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Diane McCracken on 2010-10-26 15:22
Do you sell parts? I am looking for a replacement potentiometer for an Emerson-Rittenhouse RC 633. It is labeled Clarostat 140-6747/ 135-51.

—> Purchase or Repair:
#Rittenhouse by john rohter on 2011-03-03 21:43
Looking for instruction for the door chime opporation.

—> Purchase or Repair:
#Rittenhouse by Christopher Cruz on 2011-03-09 13:15
Hellohave a 520 Beverly and it is working but I took it apart and found the rubber grommets and the felt strike pads are bad i am looking for replacements.ThanksChris

—> Purchase or Repair:
#Rittenhouse by Bill Chellberg on 2010-09-18 22:20
What transformer do I need for this?Thanks

—> Purchase or Repair:
#Rittenhouse by GENE LAYNE on 2016-07-28 12:11
Can you advise if a Emerson Rittenhouse RC 577 Doorbell mechanical chime will work with a 24V Transformer?I have a 16V and wanted to add a camera to this?ThanksGene 732-754-1205I cannot locate a manual im guessing this was made in the 70\'s

—> Purchase or Repair:
#Rittenhouse by FLORENCE LUM on 2010-01-22 03:42
Is there someone in Honolulu, HI whom I can contact to test and repair my intercom, and replace my ON/Off switch @ the MASTER SPEAKER?We have enjoyed our unit for many years, since 1968.

—> Purchase or Repair:
#Rittenhouse by Frank Giudice on 2009-10-23 16:36
I have a clock and doorchimes door bell model RC-633.I would like to get relacement part for the door bell part the clock is still working.Can you help me

—> Purchase or Repair:
#Rittenhouse by IRA G NICHOLS on 2025-07-08 20:58
I have a rittenhouse model c8204 that stopped working, had been working for years. New outside doorbell installed my be the cause.Can I test the bell by shorting the two screw terminals on the rittenhouse inside unit.

—> Purchase or Repair:
#Rittenhouse by Tony Falco on 2012-04-17 19:38
Do you have available a manuel for the emerson ritterhouse RCM-4 intercom. I have to re- install mine

—> Purchase or Repair:
#Rittenhouse by paul suter on 2007-02-12 03:05
I have a old intercom in an apartment building that has door locks, buzzer, and voice. the call and voice speaker does not work. all the other apartments are working good. Is there a replacement for the apartment units. or a upgrade?

—> Purchase or Repair:
#Rittenhouse by LINDA BURGESS on 2017-03-30 17:16
Have model C 8203, 10 volt door bell. Am missing the push button remote that fastens to wall outside the front door. Any suggestions?

—> Purchase or Repair:
#Rittenhouse by Kathie Hiers on 2009-03-11 03:19
I bought a house built in 1950 with an old Rittenhouse door chime, Model #365. I have no idea if it can be repaired. I don\'t have the front door button. The inner workings are very dirty. Do you think it\'s worth sending to you? Thanks, Kathie

—> Purchase or Repair:
#Rittenhouse by Roy Snelgrove on 2011-02-24 02:47
The door chime is not working properly in that some of the hammers are not striking properly. sometimes they reach the tubes and sometimes not. They are all active but not as strong as they should be .I have turned down the adjuster and none strike and when turned up, it is as I have described . The…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Sharon on 2016-11-27 00:16
we have an old rittenhouse intercom system. the units look old but still works fairly well. need information on how to update system. we're remodeling in some areas and would like to check out updating units. don't have specs on the system. not sure of specs but Name on the system is Ritte…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Larry Graham on 2011-01-02 02:03
I am looking for a wiring diagram for a Rittenhouse, Spartan Electric, Fayettevile NC C8845 unit which is 30 to 35 years old. It seems to be either able to use two D cells or 16V transformer but I am got sure how to wire it up. Any ideas? Thanks.

—> Purchase or Repair:
#Rittenhouse by Bradley Lowe on 2015-12-05 21:41
HelloIt came with the house had a ele.and he had no luck with repair

—> Purchase or Repair:
#Rittenhouse by Jorge Crespo on 2015-05-11 04:05
Riitenhouse chime model C8538R to connect into the AC adapter 16 volt .

—> Purchase or Repair:
#Rittenhouse by Vev lee on 2013-05-19 16:43
I need the wiring digram for model number c8535

—> Purchase or Repair:
#Rittenhouse by Jeffrey on 2008-11-22 22:27
This problem may be caused by a lighted doorbell. After the bell is wrung, the light will re-illuminate. When that happens it may be drawing just enough power to make the door chimes think that the button was pressed once again. This is a repeating pattern.If a lighted door button is used, the solut…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Tom Bell on 2019-04-10 01:02
I have a Rittenhouse 631/632 doorbell that works ok but the clock motor is noisy. Can I buy a replacement motor for it?

—> Purchase or Repair:
#Rittenhouse by sal on 2018-01-16 16:43
Trying to obtain new springs and strikers/drivers

—> Purchase or Repair:
#Rittenhouse by Corinne Censulla on 2012-02-29 17:56
I have a very old doorbell/ clock combination. The Model # is 450. The chimes work but not the clock. Since it is installed into the wall is there one the will replace using the same insert?

—> Purchase or Repair:
#Rittenhouse by Dick on 2018-12-06 23:40
Part #C80Q0 door bell switch.Can I order a replacement ?

—> Purchase or Repair:
#Rittenhouse by R.Sarin on 2010-08-11 23:11
Hi I need a cover for the rittenhouse door chime model 380 can u pls get back to me thank you

—> Purchase or Repair:
#Rittenhouse by Jim Fields on 2012-11-19 16:03
I have a schematic for Models M7010, M7011, M7012, M7020. The document also has AM Alignment, FM Alignment, Troubleshooting chart, and list of replacement parts for printed circuit board.

—> Purchase or Repair:
#Rittenhouse by Galen Beaupre on 2019-06-10 14:27
I have a Rittenhouse Model 526.What would cost to test it?

—> Purchase or Repair:
#Rittenhouse by phil hartshorn on 2017-01-10 16:24
need wiring diagram for c8538r door chime

—> Purchase or Repair:
#Rittenhouse by ElectraChime on 2017-01-22 03:43
I can make new bells for this chime. See my sites: doorbellmuseum.org and electrachime.comBestRobert

—> Purchase or Repair:
#Rittenhouse by Scott Poulos on 2009-05-23 13:59
I am looking for a replacement unit or one that is compatable and larger to cover existing hole. please respond even if you are not interested or cant get what I need so I can try elsewere.

—> Purchase or Repair:
#Rittenhouse by TONY HOVANEC on 2011-08-09 16:09
HAD LIGHTNING STRIKE AND WOULD LIKE TO REPLACE IF YOU HAVE A RETRO UNIT TO REPLACE IT THANK YOU

—> Purchase or Repair:
#Rittenhouse by George Pond on 2019-07-27 20:32
Can you repair the solo kids on this 1950s era doorbell?It’s generally ok except that some of the parts that slide in the tubes to ring the chimes are lost. I could send it in or you could sell me the parts to fix it myself. Thanks,George Pond

—> Purchase or Repair:
#Rittenhouse by Paul Winchock on 2018-10-15 21:41
I have a Rittenhouse 550, 551 doorbell chime.The unit itself works fine. What I am missing (which someone was supposed to nor trash) is the transformer that sequences the chimes. Do you have a transformer for this that will work? And if so, obviously, what would one cost?Thank you for taking the tim…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Craig on 2018-12-27 00:39
I have a 620R, but your post was a long time ago. Did you get an answer?

—> Purchase or Repair:
#Rittenhouse by Jennifer Walker on 2009-04-26 01:22
I have read several threads asking about updating an old Rittenhouse system. I would like to do the same, hopefully avoiding the need to replace drywall, etc., since this system is considerably larger than the Nutone products. I couldn\'t find any responses addressing whether or not there were solut…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by stan Mc Neely on 2014-02-21 17:39
some ONE TOOK MY 577 Apart, I need a picture of how the Chimes goback on the unitTHANKS

—> Purchase or Repair:
#Rittenhouse by Dick Dingman on 2009-04-20 19:15
I purchased this residential unit in 1986. It is now giving a significant hum and does not produce all of its chimes.Does this give you a clue as to repairability?

—> Purchase or Repair:
#Rittenhouse by isagani l. cua on 2015-03-13 18:40
Sir: Please help me diagnose the problem of my C8204 door chime, andthis morning I heard a noisy sound from the unit. And please give menearest service center here in Chino hills, CalifornialThanks

—> Purchase or Repair:
#Rittenhouse by Bob Przybylski on 2018-11-28 01:06
I have a Rittenhouse door bell model c8355 and the transformer (that is what I think it is) has failed & does nothing but hum. Can I get a new transformer? or can I buy a replacement at the local home depot or Lowes?

—> Purchase or Repair:
#Rittenhouse by Rick Martin on 2015-07-19 07:20
The Rittenhouse C8578-1 135-7351-01 door chime unit caused downtime today from 930 AM to 1145 AM, impacting our operations. Need quick resolution before the next shift. Thank you.

—> Purchase or Repair:
#Rittenhouse by Earl Miller on 2012-10-11 01:23
Is there a new updated unit (with new bells & whistles) that can use the existing wiring and wall recesses of the old units. If so, where can I get them and what would be a ballpark pricing? Thanks

—> Purchase or Repair:
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

—> Purchase or Repair:
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.