Rittenhouse Service & Repair Forum

I have a rittenhouse westminister door chime master model 631 and 632 that I removed from my family home when it was being sold. I have everything except the Rittenhouse no. 42 transformer, which is need before the electrician can install it in my home. Do you have this transformer or know where I can get one? I appreciate your help.

β€”> Purchase or Repair: Ticket Image

β€” Posted by Diane P on 2019-05-22

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by Roy Snelgrove on 2011-02-24 02:47
The door chime is not working properly in that some of the hammers are not striking properly. sometimes they reach the tubes and sometimes not. They are all active but not as strong as they should be .I have turned down the adjuster and none strike and when turned up, it is as I have described . The…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Virginia Melchi on 2011-05-25 22:34
Purchased a use Rittenhous Westminster door chime / clock; Tetechron Motored, model #8633. I need a wiring diagram for this unit.Thank you,Virginia Melchi

β€”> Purchase or Repair:
#Rittenhouse by Ray Smith on 2011-11-29 00:44
very low sound no door chime

β€”> Purchase or Repair:
#Rittenhouse by Mike on 2025-06-05 15:12
Trying to hook up ring with the rittenhouse 531 model. Not sure how the wiring should be set up? 4 white and red wires with 0-4 posts?

β€”> Purchase or Repair:
#Rittenhouse by Lynn Young on 2015-09-20 19:01
Did you locate the 3 coils you were looking for ? I also need one

β€”> Purchase or Repair:
#Rittenhouse by paul caley on 2010-10-09 16:33
plungers have stopped (tried lube) is model w clock can they be replaced by myself or must this be done by a pro or can the entire panel be more easily replaced thank you

β€”> Purchase or Repair:
#Rittenhouse by Jolene Gross on 2015-08-16 14:22
I have a Rittenhouse model c8229 door bell in my home that is not working. I would like to have it repaired.Thank you,Jolene Gross717-781-3692

β€”> Purchase or Repair:
#Rittenhouse by Chuck Duncan on 2013-03-20 00:33
Was working well until I sanded and painted the kitchen. I took the chimes down to paint, put them back and nothing works. I get voltage coming in but it doesn\'t move anything.

β€”> Purchase or Repair:
#Rittenhouse by Tony Falco on 2012-04-17 19:38
Do you have available a manuel for the emerson ritterhouse RCM-4 intercom. I have to re- install mine

β€”> Purchase or Repair:
#Rittenhouse by Jim Fields on 2012-11-19 16:03
I have a schematic for Models M7010, M7011, M7012, M7020. The document also has AM Alignment, FM Alignment, Troubleshooting chart, and list of replacement parts for printed circuit board.

β€”> Purchase or Repair:
#Rittenhouse by Maria on 2017-06-19 14:33
I need wiring schematic for Emerson door chime model C8578-1

β€”> Purchase or Repair:
#Rittenhouse by Tobie Ross on 2018-04-13 02:54
I have a Sears Solid State Am-FM Master Station Radio/Intercom Model 113.35150 built by Emerson Electric. Can you repair this station. Please advise/

β€”> Purchase or Repair:
#Rittenhouse by Kathy Grant on 2018-09-24 16:43
I recently purchased an older home that has a Model # RC-475 - 16 volt door chime that works fine, but lacks the cover. Is it possible to purchase just a cover from you or is something like this no longer available. Amazon has one but the mfg. dimensions wouldn't fit. As close as I can measure …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Clay Johnson on 2015-03-08 20:13
Please provide information or assistance regarding Rittenhouse part number C8578-1 135-7351-01, described as a door chime. Thank you.

β€”> Purchase or Repair:
#Rittenhouse by Debbie Solovey on 2014-10-25 01:56
Hello, I am living in the house I grew up in and all of a sudden I noticed thatthe front doorbell was not working. The side doorbell hasn\'t worked for a long time. I have done some research so I will give you the information I have.Nutone Chime Signal, made in USA 1952, Model K 26 902 or 002It is a…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Terri McDougall on 2012-04-06 14:55
Our house was built in 1978 and we purchased it in 1997. It had the Rittenhouse monitor system in place with the main unit in the kitchen and smaller units scattered thought the house and in an attached apartment. The unit has never worked since we have been here and I was wondering if it is repaira…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by glen e peterson on 2007-08-23 19:16
I h ave a rittenhouse intercom system that does not work star system 9000 I would love to get it to work again. Can you help me with this thankyou glen

β€”> Purchase or Repair:
#Rittenhouse by Jessica Memmott on 2010-07-22 18:45
My model 552 is not working. Licensed Electrician checked it out and it need replacement parts. I want to keep actual doorbell, because of sentimental reasons.

β€”> Purchase or Repair:
#Rittenhouse by Jeff Swiger on 2009-12-09 21:38
I would like to replace my working existing RMC-4 rittenhouse intercom with a compatible unit. While using the existing wires? Suggestions _ and would you be interested in the old unit and speakers - 8 + 1 doorThanks,

β€”> Purchase or Repair:
#Rittenhouse by R.Sarin on 2010-08-11 23:11
Hi I need a cover for the rittenhouse door chime model 380 can u pls get back to me thank you

β€”> Purchase or Repair:
#Rittenhouse by John Reaney on 2017-02-11 01:00
Hello, I have a rittenhouse door sentry. #M9035 w/ a M 9305 door station. The indoor station seems to work, it unlocks the door when the button is pushed. The M9305 out side station is my problem, the speaker is fried and the button is missing. Would you have these items? or where I might find them.…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Craig on 2018-12-27 00:39
I have a 620R, but your post was a long time ago. Did you get an answer?

β€”> Purchase or Repair:
#Rittenhouse by Tom Bell on 2019-04-10 01:02
I have a Rittenhouse 631/632 doorbell that works ok but the clock motor is noisy. Can I buy a replacement motor for it?

β€”> Purchase or Repair:
#Rittenhouse by Jorge Crespo on 2015-05-11 04:05
Riitenhouse chime model C8538R to connect into the AC adapter 16 volt .

β€”> Purchase or Repair:
#Rittenhouse by Francis Roberts on 2007-05-24 22:32
Need new springs for the hammers. This is an old door bell and it has lasted about 40 years. The new ones are sick. This is the best I have heard and would like to keep it another 40 years.

β€”> Purchase or Repair:
#Rittenhouse by David Hocevar on 2011-12-05 17:56
I have a ritenhouse emerson door chime unit. It just started chimeing for no reason I had to disconnect it to silence it. Now when I hooked it back up nothing happens. Clock doesn\'t work, chimes don\'t work.Model 086331 4 tubed chime It also has a teledcrome syncronis motor. Any hope for it.Thank Y…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by colleen on 2010-03-10 04:32
i have a model 7035 that was removed from the wall to repair the wall. Now I need to reconnect - but don\'t know how the wires go together. Are there any instructions available?

β€”> Purchase or Repair:
#Rittenhouse by David Peterson on 2006-03-01 03:17
The reception is pretty poor and weak on the volume. Do your know if there is an transisterized replacement receiver that will fit into the 1970\'s model. Thanks, David......

β€”> Purchase or Repair:
#Rittenhouse by Paul Gilbert on 2016-06-07 01:02
Need to replace existing bell system with new Paul gilbert

β€”> Purchase or Repair:
#Rittenhouse by stan Mc Neely on 2014-02-21 17:39
some ONE TOOK MY 577 Apart, I need a picture of how the Chimes goback on the unitTHANKS

β€”> Purchase or Repair:
#Rittenhouse by Diane Reichard on 2010-04-14 13:54
Hello! Do you have any parts for Rittenhouse (Emerson) All Transistor Radio-Intercom System, Model RM-1 (AM radio) or RM-2 (AM/FM radio)? Our system dates from the 1960\'s--still going strong. But I need knobs and especially the instruction manual because I don\'t know how to answer and use the exte…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Barbara on 2006-08-27 17:45
This is an old system I would like to replace. Does the wire plugs have to be replaced. I would like sm=omthing that will be compatable with the wire plugs. Do you have any suggestionsThank You

β€”> Purchase or Repair:
#Rittenhouse by GUY DALFINO on 2013-01-24 17:30
I THINK I NEED A TRANSFORMER CLOCK WLL NOT RUN TX IN ADVANCE gUY

β€”> Purchase or Repair:
#Rittenhouse by David Smith on 2009-03-16 13:36
I need the three coils for the 526 Rittenhouse. ( a power surge burned 2 of the three).

β€”> Purchase or Repair:
#Rittenhouse by Gord Sweatman on 2017-09-01 21:46
Removed outer casing - now doorbell doesn't work - noticed loose redwire - where do I attach?

β€”> Purchase or Repair:
#Rittenhouse by Leslie Southern on 2009-06-05 13:08
We are looking for the Rittenhouse C8931R Wireless Chime Receiver.We are an electrical contractor and are working with a customer who loves her chime system but wants to expand it to other areas of her home.Can you point me in a direction to locate one of these?Thank you.

β€”> Purchase or Repair:
#Rittenhouse by Tedd Boomershine on 2012-04-22 21:49
The clock works fine. Three of the door chimes work, but the fourth and fifth strikers do not work. Do you repair and or have parts to recondition? Thanks, Tedd

β€”> Purchase or Repair:
#Rittenhouse by dave walters on 2008-10-24 14:59
Just wondering i have a rittenhouse system rcm-1 and the intercom system part does not seem to be working. We can broadcast for the main unit and it is heard in the other units but when we try to broadcast from one of the other units to the main you can not hear the person ? Anysuggestions or do you…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by David on 2018-03-04 18:16
Have you ever heard of a response on the Rittenhouse 631/632. I too am refurbishing one and need to know the correct tranformer voltage needed and a wiring diagram surely would help. Any insight?

β€”> Purchase or Repair:
#Rittenhouse by Mary Anne Fuscaldo on 2009-12-25 23:04
I moved this door chime/clock when it was working from one home to another. The electrician that hooked it up did not do it correctly and I have no schematic for how it should be wired. I know it needs three wires but not sure on which of the 7 screws they get wired to. They do not indicate Com or T…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Bob on 2007-04-07 23:14
We have the same system in our home. Did you find any compatible system? Did you replace your system? If so, what system did you use? Thank you. We need to replace everything except the wiring.

β€”> Purchase or Repair:
#Rittenhouse by O. H. Towers on 2010-01-25 16:00
We are also electrical contractor company(Towers Electrical Serv. Inc)We are looking for a model C8931 R Chimer Receiver also a sender unit if possible.We cannot find any info on this item it was made ty Rittenhouse Fayettevilole, nc. 28302

β€”> Purchase or Repair:
#Rittenhouse by Marie Gunderman on 2007-11-26 01:41
We purchased our present home in 1998. It was custom built in 1983 with many upgrades that were available at that time. Unfortunately since we have lived here the system does not work. The main unit is 17\' wide and 9\" tall. There are 12 units scattered throughout the house. They each measure 7.5\"…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jamie Wingler on 2009-08-30 05:41
I have an inoperative Rittenhouse Model 7021 intercom system as well. Can I fix it or do I have to buy new?

β€”> Purchase or Repair:
#Rittenhouse by sonny sadler on 2011-11-21 16:12
i would like to have an updated model the one i have was installed in 1977 it makes noise, drifts off stations all controls are noisey and sound is garbled. can you tell me where to get help.

β€”> Purchase or Repair:
#Rittenhouse by Diane P on 2019-05-22 14:20
I have a rittenhouse westminister door chime master model 631 and 632 that I removed from my family home when it was being sold. I have everything except the Rittenhouse no. 42 transformer, which is need before the electrician can install it in my home. Do you have this transformer or know where I c…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jason on 2021-11-27 23:30
I believe it was 16v AC current . not DC at least thats how mine is.

β€”> Purchase or Repair:
#Rittenhouse by bill whitacre on 2013-11-16 18:30
need to reconnect wires to front, rear & trans positions.

β€”> Purchase or Repair:
#Rittenhouse by Sylvia on 2016-02-03 03:15
4 out of 10 times whenever I press the button it works.How do I know if the transformer that needs replacement or if the wiring itself that went wrong? I have replaced the button and it should not be the problem itself.How much would it cost if you send someone to fix it?Thanks.β€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Eric Schneider on 2012-02-04 21:58
Do you know where I can find the outdoor part you push to ring for this Emerson Model C8203? Thanks for your time.Eric Schneider

β€”> Purchase or Repair:

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.