Rittenhouse Service & Repair Forum

Good day, I would need the wiring diagram for a Rittenhouse Clock Model 631/632. Just saved the clock from our old house before remodel and we want to install it back with a running clock and the chime.Thank youRadu 650-450-4806

—> Purchase or Repair: Ticket Image

— Posted by radu munteanu on 2022-04-20

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 315 Comments

#Rittenhouse by DANNY on 2010-05-06 16:48
I AM A ELECTRICAL CONTRACTOR AND HAVE BEEN TOLD THAT NUTONE WILL WORK USING EXISTING WIRING THE PROBLEM IS NUTONE WILL NOT WARRANTY IF YOU DO NOT USE NUTONE WIRE, BUT THEY DO HAVE A 30 DAY RETURN POLICY TRY THE SYSTEM IF IT DOES NOT WORK TAKE IT BACK ASAP

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Charles Cheshire on 2018-07-13 22:04
Cannot reset time seems stripped.Only two of the chimes work.Where are you physically located.ROUGH repair cost.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by van Aree on 2009-02-26 20:19
I am looking for a copy of Rittenhouse rm5 house intercom owner\'s manual.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Donna Dodson on 2007-03-02 16:22
I would like to see if I can get this to work. But I don\'t know where to start.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Bob on 2007-04-07 23:14
We have the same system in our home. Did you find any compatible system? Did you replace your system? If so, what system did you use? Thank you. We need to replace everything except the wiring.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Anthony Butts on 2011-10-02 19:14
The unit works, but possibly in need of some service. The AM radio works , but no FM. There is a bit of background noise in the system.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Eric Zetterberg on 2011-02-11 19:49
I have three doorbells connrcted to chimes but only one works, any suggestions?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by David Smith on 2009-03-16 13:36
I need the three coils for the 526 Rittenhouse. ( a power surge burned 2 of the three).

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Cathy Kirkwood on 2014-08-21 21:30
I purchased a home in Honeoye Falls, NY. It has an RCM 3 intercom that works and I would like to get a manual for it. Is it possible to get instructions for it?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Jim Fields on 2012-11-19 16:03
I have a schematic for Models M7010, M7011, M7012, M7020. The document also has AM Alignment, FM Alignment, Troubleshooting chart, and list of replacement parts for printed circuit board.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Richard Burnham on 2021-03-28 21:10
Front and back door bells. I need a diagram showing how to connect the wires from the doorbells. Front works with one wire from Front doorbell going to Terminal B and the other going to Front in the 16 VAC group. I assumed one wire would go from Back doorbell to Terminal A and the other to Back in t…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by k. chang on 2009-06-17 02:34
how do we get this old door chime to work again?we\'re already replacing the batteries, what else should we do?thanks

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Mark Ivess on 2011-08-01 00:00
Hey there, I've been tasked with looking into an issue with a Rittenhouse C8578-1 135-7351-01 door chime. I don't usually work on hardware like this, so I could really use some guidance on how to fix or replace it. Any help or advice you can provide would be greatly appreciated. Thanks in advance!—>…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Mark Palmer on 2012-09-06 21:18
I have 2 Rittenhouse intercom speakers that need to be replaced. They both measure 9 1/4\" long. 6 1/4\" wide and 3 1/2\". Do yo have suitable replacements? If so, how much are they? Price of each unit, tax if aplicable and shipping charges for a total net price.Thanks in advance for your prompt rep…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by mccammond99@att.net on 2016-03-19 17:03
is there anyway i could get another one of these door bells?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Larry Graham on 2011-01-02 02:03
I am looking for a wiring diagram for a Rittenhouse, Spartan Electric, Fayettevile NC C8845 unit which is 30 to 35 years old. It seems to be either able to use two D cells or 16V transformer but I am got sure how to wire it up. Any ideas? Thanks.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Mark Hefner on 2012-05-18 01:33
I have a emerson rittenhouse rcm 4 main unit with IR6 speakers throughout a house i purchased and am interested in upgrading the entire system. Is there a replacement system where it can be changed out?It will be a few months before I am ready to do it, but am trying to look at options and replaceme…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Dan Mazzola Sr on 2020-05-31 15:36
I’m in need of a sequence timer for the above mentioned Emerson Rittenhouse clock/chimePlease advise on getting 1 of them by email or by calling me at 617/590-3509New or reconditioned

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Andrew Lazazzera on 2017-01-16 17:16
HAVE --MODEL DS-2 DOOR SENTRY SAYS 'NOT TO CONNECT TO POWER SOURCE OTHER THAN STANDARD 16 VOLT CHIME TRANSFORMER'NEED TESTING OF ITS TRANSFORMER.I THINK ITS THE TRANSFORMER!WHAT IS PROCESS TO FOLLOW FOR THIS?ANDREW h=773-589-0150 c=773-899-0423

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Mark Malan on 2017-05-17 14:32
My manual says 4-8 Note Chime Models (534, 535, 552, 577, 618, 633). I don't know which one I have. It has long chime tubes and a clock on top. The door bell works great, but the clock doesn't.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by J. G. Colbert on 2010-09-28 22:30
The rheostat is broken on this unit otherwise the unit is as melodious as it was 40 years ago.The numbers on the rheostat are 1406417 and 135-51 The motor is a Telechron synchronous motor. 118V--16 Model 3151 RPM 3. W. 4.CantI purchase the replacement rheostat and have it shipped to PMB 399 at the a…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Gord on 2011-11-24 21:00
Jessica:I have the same model door chime, with the same problem. How did u make out with yours? Do you know any of the history of this chime. From what I can surmise, it was produced after WW2 and that would fit as it was in my parents house when i was born in 1954. I have a friend that is an electr…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by ElectraChime on 2017-01-22 03:43
I can make new bells for this chime. See my sites: doorbellmuseum.org and electrachime.comBestRobert

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Larry Yudkowitz on 2020-05-13 00:16
I have Model 380 16V. I had connected it ot a Ring Video 2 Doorbell and it worked fine for several months. Now there is a loud humm coming from the chime. I think the Ring ihas a problem. Ring says the chime may not be compatible. Ring says the model 382 is compatible. Whould you know the difference…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by sheila on 2011-09-05 18:24
Would you know where i can find a C8931R?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by e. jureller on 2024-12-01 00:00
Urgent Follow-Up Rittenhouse RM Intercom DownDear Team,I am following up on the previous message regarding the non-functional Rittenhouse RM intercom unit. It is imperative that we address this issue

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Jessica Memmott on 2010-07-22 18:45
My model 552 is not working. Licensed Electrician checked it out and it need replacement parts. I want to keep actual doorbell, because of sentimental reasons.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Mark Danko on 2015-09-10 19:17
Hi, need repair to this unit, sound cuts in and out when volume control knob is turned/wiggled. Moving molex 5 pin connector on circuit board also causes power to cut in and out. Mode delector knob has become stiff to operate. Please send estimate if repair is possible, thanks

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Tom Gleason on 2011-03-31 01:27
Looking for a sequencer box for a model 552 doorbell chime. I know they are rare. Does somebody make a retro fit or do you have a good used one. If none of the above then how about schemetics and I will get one made. Thanks-Tom

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Earl Miller on 2012-10-11 01:23
Is there a new updated unit (with new bells & whistles) that can use the existing wiring and wall recesses of the old units. If so, where can I get them and what would be a ballpark pricing? Thanks

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Bob Przybylski on 2018-11-28 01:06
I have a Rittenhouse door bell model c8355 and the transformer (that is what I think it is) has failed & does nothing but hum. Can I get a new transformer? or can I buy a replacement at the local home depot or Lowes?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Jim on 2008-12-29 15:59
Are there any Emerson Rittenhouse intercom main stations from the mid-sixties available?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by dan mazzola on 2017-02-17 16:32
need a sequence timer for a emerson rittenhouse model # 632 631

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Ellen on 2011-12-23 17:22
The installation manual has been misplaced and I am not sure which wires go to which connection. There is a red wire, a black wire, and a yellow with a green wire. The places to connect are for the front, rear, and transformer. Please advise. Also, there is a possibility that the transformer doesn\'…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by john rohter on 2011-03-03 21:43
Looking for instruction for the door chime opporation.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by MARK WILSON on 2011-01-12 14:35
This is a Mechanical doorbell with Electronic Control Board. I need Someone to give me an estimate for repair or tell me where I can get parts for this device. Thanks, Mark Wilson

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by DominicJ. Carini on 2009-07-23 03:03
I have a 30 year old rittenhouse door chime with the 4 sequential chimes, one of the plungers has gone lazy. I took the transformer out to try to clean it and lost the little spring that gives the plunger resistance . Do you have any ideas ?Or do you sell parts, perhaps a whole tansformer. I tried t…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Harry Yagi on 2017-05-11 12:40
Due to the worn-weakened spring on the hitting bar which do not pop out from the solenoid hole. Do you sell the spring or the entire solenoid with the hitting bar?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Lori on 2008-12-29 00:49
Years ago lightening hit house the chime stoped working the unit is in the kitchen and of coarse the door bell at the front door to push with finger ..doesnt work anymore can this be fixed ??/

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Howard Robertson on 2012-11-19 01:59
intercom system does not work.would like to have it repaired.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Rick Martin on 2015-07-19 07:20
The Rittenhouse C8578-1 135-7351-01 door chime unit caused downtime today from 930 AM to 1145 AM, impacting our operations. Need quick resolution before the next shift. Thank you.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Don Pieschel on 2011-06-25 22:05
I have a RM-2 or a M9401 rittnhouse intercom I need a manual or schematic.any ideas where to locate.Don

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Jim Drouillard on 2008-05-16 02:50
I have the above mentioned door chime (Rittenhouse door chime model C8536) that does not work correctly. There where some broken wires from the transformer coils that I soldered back on and now it does not work correctly. Do you have a schematic for this unit?

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Francis Roberts on 2007-05-24 22:32
Need new springs for the hammers. This is an old door bell and it has lasted about 40 years. The new ones are sick. This is the best I have heard and would like to keep it another 40 years.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Emily Gladden on 2016-10-16 21:20
When you press our door bell button a chime is not coming out of the box in the outlet.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Leslie Southern on 2009-06-05 13:08
We are looking for the Rittenhouse C8931R Wireless Chime Receiver.We are an electrical contractor and are working with a customer who loves her chime system but wants to expand it to other areas of her home.Can you point me in a direction to locate one of these?Thank you.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by jim Snyder on 2012-01-12 05:28
A friend of mine has a doorbell that i am hoping to repair and would like to find the wiring diagram for it if possible. The only tag I can find on it saysArtolier Lighting & Sound Div. Emerson Electric Co. Rittenhouse Operations Honeoye Falls NY 14472 Model RC203 or RC208 Volt 10 There are three te…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Rittenhouse by Paul Gilbert on 2016-06-07 01:02
Need to replace existing bell system with new Paul gilbert

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by Agnes R. Kellan on 2009-11-06 01:18
I have my radio-intercom since 1969--In hasn\'t worked for about three years. I have two stations.

—> Purchase or Repair:
➡️ Reply
#Rittenhouse by LINDA BURGESS on 2017-03-30 17:16
Have model C 8203, 10 volt door bell. Am missing the push button remote that fastens to wall outside the front door. Any suggestions?

—> Purchase or Repair:
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.