Cincinnati Milacron for Service call 1-336-969-0110 at Industrial Electronics Repair

Cincinnati Milacron Service & Repair Forum

I\'m presently looking for a wiring diagram for a Cincinnati milacron milling machine. MODEL#-LL, Procuct#-315-16 plain dial type, Serial#-3104PT8-0015, ACVOLT-460, PH-3, HZ-60, Control diagrams-F-314290. Any information you can provide would be greatly appreciated.Thanks,Brian Petit

— Posted by Brian Petit on 2008-04-02

Reply🗨️Ask a New Question Below❓

If you need your Cincinnati Milacron unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 19 Comments

#Cincinnati Milacron by HALCOM INT. on 2007-03-16 17:27

HELO,WE HAVE A CNC CINCINATI MILACRON MAXIM 500 MACHINE WITH ACROMATIC 950 CONTROLWE ARE LOCKING FOR CPU 3-533-0346G USED,AND OUR QUESTION IS IF WE CAN FIND IT IS POSIBLE CHANGE THE CPU FOR 3-424-2026ATHANKSHalcom International

#Cincinnati Milacron by cindy dase on 2007-09-06 23:57

machine is arrow 1000. starts up until and says keypad touch screen missing. any suggestions?

#Cincinnati Milacron by Ed on 2008-03-06 10:31

Cindy Dase wrote \"machine is arrow 1000. starts up until and says keypad touch screen missing. any suggestions?\"Cindy,Have you been able to locate the problemEd

#Cincinnati Milacron by Brian Petit on 2008-04-02 14:13

I\'m presently looking for a wiring diagram for a Cincinnati milacron milling machine. MODEL#-LL, Procuct#-315-16 plain dial type, Serial#-3104PT8-0015, ACVOLT-460, PH-3, HZ-60, Control diagrams-F-314290. Any information you can provide would be greatly appreciated.Thanks,Brian Petit

#Cincinnati Milacron by douglas yeh on 2008-08-18 22:55

Dear Sir5:We have a Cincinati CNC machine using Acromatic 2100 control system.The machine has started to boot under DOS, then Windows NT4.0 has been loaded. It then load Vicker software and the monitor color changed to pink stripe. We can see nothing but the pink striped monitor thereafter. I am not...
Show More

#Cincinnati Milacron by LUIS SANCHEZ on 2008-10-28 00:40

HI!I\'m looking for a quote on repair of a power supply unitfor a CINCINNATI MILACRON ARROW750If there is something you can help me I\'llapreciatethanksluis

#Cincinnati Milacron by Venugopal Miskin on 2008-11-22 14:59

Dear Sir,We have cincinatti milacron cnc turning centre on our machine monitor is indicating that X axis HDRW Diagnotics fail Alert code is 00453. Pls send our reply for the sameRegards,Ind-Tech Engineering,Ph 001-0836-4265858, 019880261326HUBLI-580 030 (Karnataka State) INDIA

#Cincinnati Milacron by Tom Fellberg on 2008-12-16 21:38

Hello;We have a number of Cincinnati Milacron Camac lcd screens that are in need of repair.These screens are on injection molding machines of late 80\'s vintage. The Camac was the latest control at the time. The screens are yellow lettering on a black backround. Currently we are able to read only pa...
Show More

#Cincinnati Milacron by Paul Russel-Smith on 2009-03-06 10:22

We have a break down with our Saber 1000 cincinnati \"nikken\" 5AX-300 rotary table rom chip,we are not getting any coms between the two.What can be the cause and what can be done. Appericating our location and situation here in zimbabwe africa its not easy to get parts so we are looking f...
Show More

#Cincinnati Milacron by Chinthaka Balasuriya on 2009-04-02 06:05

We are the largest tyre and rim manufacture and exporter in sri Lanka. We use many machines in our production line.We have CINCINNATI MILACRON – SABER 500 CNC vertical machining centre. But unfortunately it have a problem.Z Axis moving Down During Power cut upto 5mm. Z Axis have the Break Motor &...
Show More

#Cincinnati Milacron by suyatno on 2009-06-17 11:56

Problem or Bad IO CHMD + CMHD AND AXISSERVO DV5

#Cincinnati Milacron by Mark on 2009-12-16 15:31

Hello, I have a cincinnati milacron Lathe with a VFS5 275/2604A-10 Spindle drive, do you repair these drives? what would the average cost be to do so. Thanks YouMark

#Cincinnati Milacron by ALEJANDRO on 2010-04-12 20:03

HIWe have a VFS5-275-00-2604A VICKERS DRIVER.with the MOTION LINK PLUS SOFTWARE appears a error No 18 BAD TL. but the boars are the same that we used before.We need the password to unblocked the software to reinstall the TL file, that we have. The TL file that we have is VFS5 v 1.03cC with a compens...
Show More

#Cincinnati Milacron by Terry L. Crow on 2010-08-04 22:03

We have a bunch of Cincinnati Milacron electronics we striped out of a Sabre, 2100, 750 and an arrow 500 VMC\'sLet me know and I\'ll send you pictures

#Cincinnati Milacron by shane brumbaugh on 2010-11-17 23:20

I am trying to find the operators and set-up manual for a vickers bds4210-23414w32. any help would be great.Thanks

#Cincinnati Milacron by Ralph Remington on 2013-04-11 14:29

The part number is 840777/I and could you provide a price estimate.

#Cincinnati Milacron by rejil on 2015-03-04 00:00

Cincinnati Milacron 3 531 2204a unit not powering on. Need immediate repair assistance.

#Cincinnati Milacron by Miroslav Petkov on 2017-04-24 08:51

I'm looking for a electrical diagram for a Cincinnati Milacron machine.Best regards,Miroslav Petkov

#Cincinnati Milacron by schuessler on 2024-10-31 00:00

Based on my experience, I've seen similar issues with the CINCINNATI MILACRON 3-533-0780G GCPU. The common symptoms typically involve erratic system behavior, frequent error messages, and potential communication failures. These could indicate a variety of potential issues, including software glitche...
Show More

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.