Rittenhouse Service & Repair Forum

I have a rittenhouse model c8204 that stopped working, had been working for years. New outside doorbell installed my be the cause.Can I test the bell by shorting the two screw terminals on the rittenhouse inside unit.

β€”> Purchase or Repair: Ticket Image

β€” Posted by IRA G NICHOLS on 2025-07-08

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 315 Comments

#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by David Peterson on 2006-03-01 03:17
The reception is pretty poor and weak on the volume. Do your know if there is an transisterized replacement receiver that will fit into the 1970\'s model. Thanks, David......

β€”> Purchase or Repair:
#Rittenhouse by Craig on 2018-12-27 00:39
I have a 620R, but your post was a long time ago. Did you get an answer?

β€”> Purchase or Repair:
#Rittenhouse by radu munteanu on 2022-04-20 17:35
Good day, I would need the wiring diagram for a Rittenhouse Clock Model 631/632. Just saved the clock from our old house before remodel and we want to install it back with a running clock and the chime.Thank youRadu 650-450-4806

β€”> Purchase or Repair:
#Rittenhouse by Galen Beaupre on 2019-06-10 14:27
I have a Rittenhouse Model 526.What would cost to test it?

β€”> Purchase or Repair:
#Rittenhouse by Diane Reichard on 2010-04-14 13:54
Hello! Do you have any parts for Rittenhouse (Emerson) All Transistor Radio-Intercom System, Model RM-1 (AM radio) or RM-2 (AM/FM radio)? Our system dates from the 1960\'s--still going strong. But I need knobs and especially the instruction manual because I don\'t know how to answer and use the exte…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by macgretz on 2017-04-19 20:58
I have a Rittenhouse Emerson Elec Model C8326 (perhaps 1960's) that has stopped working today. The chimes and housing seem okay, but the mechanism and bell button are old and worn out. Do you have replacement parts - and at what cost?

β€”> Purchase or Repair:
#Rittenhouse by Maria on 2017-06-19 14:33
I need wiring schematic for Emerson door chime model C8578-1

β€”> Purchase or Repair:
#Rittenhouse by karen varel on 2011-09-07 00:53
Do you sell parts for rittenhouse dooor chimes specifically Model #C8550 or do you know where I can get them?

β€”> Purchase or Repair:
#Rittenhouse by Robert King on 2010-08-02 01:52
I know this chime assembly is very old but is there a replacement kit for the hammers. they are sticking and perhaps the springs are just too soft. I\'d appreciate any help you can give me.

β€”> Purchase or Repair:
#Rittenhouse by Ronda Plomteaux on 2007-08-19 15:03
I have a Rittenhouse intercom system and am unsure of the model #. It was installed in the 70\'s. I am painting my condo and would like to replace the ivory cover with a white cover. How would I go about purchasing just a cover? Thank you

β€”> Purchase or Repair:
#Rittenhouse by Chuck Duncan on 2013-03-20 00:33
Was working well until I sanded and painted the kitchen. I took the chimes down to paint, put them back and nothing works. I get voltage coming in but it doesn\'t move anything.

β€”> Purchase or Repair:
#Rittenhouse by Ray Smith on 2011-11-29 00:44
very low sound no door chime

β€”> Purchase or Repair:
#Rittenhouse by Tony Falco on 2012-04-17 19:38
Do you have available a manuel for the emerson ritterhouse RCM-4 intercom. I have to re- install mine

β€”> Purchase or Repair:
#Rittenhouse by john rohter on 2011-03-03 21:43
Looking for instruction for the door chime opporation.

β€”> Purchase or Repair:
#Rittenhouse by A.L. Richard on 2010-08-09 13:32
My home was built in 1965 with the same Rittenhouse intercom/radio system that doesn\'t work anymore. I would like to upggrade with intercom/radio/ satellite radio system can you do the work? What would be the estimated cost?

β€”> Purchase or Repair:
#Rittenhouse by patrick stark on 2013-12-05 15:48
need wiring, replacement parts and pic of the model noted above. front door pushbutton lights, but no response from chime unit. the backdoor is working normal one chime. What may be wrong? the unit has a selector switch to scroll thru various chimes.

β€”> Purchase or Repair:
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.

β€”> Purchase or Repair:
#Rittenhouse by Jessica Rasmussen on 2010-07-17 03:18
I get typically one of three chimes to sound when the doorbell is rung, occassionally 2 followed by a buzzing sound. Some of the wires were loose and I tightened them, but still don\'t get all the tones. Any ideas on what to do to get all three chimes to ring?

β€”> Purchase or Repair:
#Rittenhouse by Hans Otto Mertens on 2008-01-01 23:36
The main unit needs repair!H.O.Mertens

β€”> Purchase or Repair:
#Rittenhouse by James L Rockney on 2021-10-04 16:06
The small piston that strikes the chime does not return back to the original position. There is a spring on the piston. It seems like the piston should have a retainer of some sort on the end to hold the spring in place. Is there supposed to be a retainer on the end of the piston to keep the spring …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by e. jureller on 2024-12-01 00:00
Urgent Follow-Up Rittenhouse RM Intercom DownDear Team,I am following up on the previous message regarding the non-functional Rittenhouse RM intercom unit. It is imperative that we address this issue

β€”> Purchase or Repair:
#Rittenhouse by Peter Taylor on 2013-02-15 23:47
I have a Ritten House Master Model 631 & 632 in my shop for repair. I would like to obtain a service manual for this item. Please advise if this is available. The clock is in bad shape as it fell of a wall and is in many pieces. Some of which I shall need to purchase.Please advise Peter TaylorTaylor…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Mickey Loveria on 2007-08-30 14:53
Existing model was put in my home maybe late 60\'s, with ivory base unit and 4 ivory receivers plus brass door unit intercom. The radio reception is irregular, fades in and out and there is much static. Sometimes have to jiggle knobs on base unit to tune radio! Any suggestions on where to go for upg…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Jim on 2010-05-01 22:41
I have the above model doorbell and really like the sound vs. the new \"electronic sound\" doorbells. Problem is the mechanism inside the doorbell (the part with the two knockers that the wires attach that hit the bells to make the sound) no longer works. Can I still get this part replaced and if so…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Steve Macha on 2026-05-26 22:27
Discovered circuit short on controller board. How can I obtain a schematic?

β€”> Purchase or Repair:
#Rittenhouse by Jessica Memmott on 2010-07-22 18:45
My model 552 is not working. Licensed Electrician checked it out and it need replacement parts. I want to keep actual doorbell, because of sentimental reasons.

β€”> Purchase or Repair:
#Rittenhouse by Withgott on 2012-04-13 00:00
Having issues with my Rittenhouse RCM-4 intercom with radio - the radio feature is not working. Need repair assistance

β€”> Purchase or Repair:
#Rittenhouse by James A. Mann on 2008-06-26 12:40
We installed our Rittenhouse intercom system in 1978 when we built our new home. The speakers look out of date and would like a better main unit. We have 4 outside units, and 7 speakers.Can we purchase new units and still use the same wiring? Would appreciate a response ASAP. Thanks Jim MannP.S. Ple…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Charles Cheshire on 2018-07-13 22:04
Cannot reset time seems stripped.Only two of the chimes work.Where are you physically located.ROUGH repair cost.

β€”> Purchase or Repair:
#Rittenhouse by Mark on 2017-09-04 20:48
I'm looking for a replacement circuit board for a Rittenhouse model C8538. Please let me know where I can purchase one.

β€”> Purchase or Repair:
#Rittenhouse by Jo Ann Redmond on 2011-10-18 23:20
Good Evening,We have a Rittenhouse Intercom System (solid state Am/FM Radio Intercome) it has got to be at least 30 years old. We are looking to replace the outside speaker box (Nu-tone). Please let us know if this item is still available. We would give you more info on the system, but cannot find s…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Raymond V Normand on 2018-11-29 17:19
Can you sell me Grommets for my Ritten house Model 236 soundbars?

β€”> Purchase or Repair:
#Rittenhouse by Michael Senay on 2011-09-08 17:07
My rittenhouse chime is about 15 years old and I would like to get it repair. I would like to know who can repairs it.

β€”> Purchase or Repair:
#Rittenhouse by Jeff Swiger on 2009-12-09 21:38
I would like to replace my working existing RMC-4 rittenhouse intercom with a compatible unit. While using the existing wires? Suggestions _ and would you be interested in the old unit and speakers - 8 + 1 doorThanks,

β€”> Purchase or Repair:
#Rittenhouse by Tom Gleason on 2011-03-31 01:27
Looking for a sequencer box for a model 552 doorbell chime. I know they are rare. Does somebody make a retro fit or do you have a good used one. If none of the above then how about schemetics and I will get one made. Thanks-Tom

β€”> Purchase or Repair:
#Rittenhouse by John Zeitler on 2012-12-05 22:32
I am looking for the cover that is a black plastic 8 3/8\" wide, 5 1/2\" high, and 2 1/8\" deep. Any idea where I can find a suitable replacement? Thanks.

β€”> Purchase or Repair:
#Rittenhouse by ann chamberlin on 2010-03-07 15:43
Jennifer Walker:Did you ever figure out what to do about replacing your Rittenhouse unit? I\'m in the same boat!Any ideas or products you have come across on your own would be appreciated

β€”> Purchase or Repair:
#Rittenhouse by Lori on 2008-12-29 00:49
Years ago lightening hit house the chime stoped working the unit is in the kitchen and of coarse the door bell at the front door to push with finger ..doesnt work anymore can this be fixed ??/

β€”> Purchase or Repair:
#Rittenhouse by curtis gast on 2015-03-16 02:25
new home to me. system not working. any help would be great. thanks

β€”> Purchase or Repair:
#Rittenhouse by Morris Hoagland on 2014-01-05 03:53
My Rittenhouse Master unit has failed. Is there a replacement unit I can purchase?

β€”> Purchase or Repair:
#Rittenhouse by Jack Mc Sweeney on 2008-09-10 22:29
This is a two unit intercom and door opener for apartments. Presently, it has current but buzzes the door open without pushing the switch, and has no voice tones.

β€”> Purchase or Repair:
#Rittenhouse by dominic Carini on 2009-07-28 00:55
Ihave about a 30 year old rittenhouse with 4 chimes.It seems that the solenoids that activate the strikers,are getting a little lazy.I have had one apart and try to clean it ,with not much succes,I even lost one of those tiny springs. I tried to replace it with a similar one ,but it\'s not right.Do …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Lynn Villano on 2011-05-06 13:29
but want door bell to continue working. Can we get wiring schematics?

β€”> Purchase or Repair:
#Rittenhouse by Virginia Melchi on 2011-05-25 22:34
Purchased a use Rittenhous Westminster door chime / clock; Tetechron Motored, model #8633. I need a wiring diagram for this unit.Thank you,Virginia Melchi

β€”> Purchase or Repair:
#Rittenhouse by elena fernandez on 2015-02-27 06:07
Hi there, I'm interested in purchasing the Rittenhouse C8578-1 135-7351-01 door chime. Could you please provide me with information on pricing and availability? I'm looking to source one quickly. Thank you!

β€”> Purchase or Repair:
#Rittenhouse by Jim Drouillard on 2008-05-16 02:50
I have the above mentioned door chime (Rittenhouse door chime model C8536) that does not work correctly. There where some broken wires from the transformer coils that I soldered back on and now it does not work correctly. Do you have a schematic for this unit?

β€”> Purchase or Repair:
#Rittenhouse by James Short on 2013-02-24 20:40
A plunger on my 50 year old door chime is not returning to the rest position when the door chime is not activated. The consequence is a continuous buzz and erratic operation when the button is pressed.Have I provided sufficient information to diagnose the ease of repair?Thank you.Jimβ€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by colleen on 2010-03-10 04:32
i have a model 7035 that was removed from the wall to repair the wall. Now I need to reconnect - but don\'t know how the wires go together. Are there any instructions available?

β€”> Purchase or Repair:
#Rittenhouse by Krzysztof Charzynski on 2014-11-26 05:14
rittenhouse model 410 not working need repair

β€”> Purchase or Repair:

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.