Pavid for Service call 1-336-969-0110 at Industrial Electronics Repair

Pavid Service & Repair Forum

I need information about a Pavid generator I need parts for this generator,all the information you got on this

— Posted by ROBERTO H DAGNINO on 2011-03-22

Reply🗨️Ask a New Question Below❓

If you need your Pavid unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 30 Comments

#Pavid by JIM KITSON on 2006-01-25 03:19

I HAVE A PAVID GEN SET MODEL J13GAW-HNEED WIRING DIAG. TO CHANGE FROM 480V 3 PHASE TO 240V 3 PHASETHANKSJIM KITSON

#Pavid by Joe K on 2006-03-15 02:45

I don\'t know if you found the information on re-straping your generator or not but if you still need a print, e-mail me and I\'ll send you what you need.

#Pavid by Paul Drudge on 2006-07-26 21:23

would a diagram of terminal location for multi voltage be available?

#Pavid by R C Engines on 2006-10-22 00:51

We have a C18H3 M-G set and we are looking for a wiring diag. Can we purchase a copy of the diag. from your company? We are having problems with the output voltage. Please email us if you can be of asst. Thank You

#Pavid by clarence silvers on 2007-12-27 03:45

Hi, i\'ve got an old c18h3 or g18h3 pavid generator, its hard to tell if its a \'c\' or a \'g\' from the dataplate. It had been working really well untill we went to fire it up to test it before the last ice storm when we noticed that the output was really fluctuating, now it doesn\'t have any outpu...
Show More

#Pavid by Ruth Turner on 2008-01-05 16:33

Where can my husband get information about the above referenced generator?Thank you.Ruth Turner

#Pavid by Anthony Woods on 2008-01-21 13:57

I have a Pavid Model G 20 H3. The Crank Timer Board is getting a start signal from the ATS but it is not sending the signal to start the Engine. The unit will start manualy. Is their anything you could suggest. Thank you

#Pavid by Harry on 2008-01-24 16:48

I need an oil pressure switch for a PAVI Generator MOD: G20H3. Yhis is a normally closed switch that starts the engine then cuts the starter off after proving oil pressure.White Diesel EngineMOD: D200S\\N: TH3432857SPEC:X99

#Pavid by Faith Epp on 2008-10-15 04:14

I have a pavid 45 kw generator head, (no engine yet) . It is a 12 wire set that I am told can be wired for 1,2,and 3 phase. It is presently wired 3 phase, parallel Y, 4 wire. Can someone tell me the wiring format for 120/240 single phase, 3 wire? my wires are marked T1-T12.I am aware that I may need...
Show More

#Pavid by STACY REED on 2009-03-03 18:53

Hello,I was wondering if you can provide me a manual for the Teledyne Pines machine?thank you

#Pavid by larry on 2009-03-25 21:35

need info for wiring digrams on gen and controll boxthanks

#Pavid by James Epp on 2009-04-10 02:32

Hope someone can help me here. I have a pavid generator head, no engine with no id tags. Is there a way to figure out the kw of this unit?I do know this much, It\'s between 35-90 kw, had a hercules diesel, ( most likly a d3000 or d3400). It is of the design that uses an adapter/spacer to join it to ...
Show More

#Pavid by Tom Robertson on 2009-05-05 03:44

Dear Sirs,I have a Pavid unit on top of the Sullair genset.Model No.: 248275-001Serial No.: 6184I need some information on the functions of the controller board.Does the controller board regulate the RPM of the engine electronically. or does the unit need a solenoid or mechanical govenor.The unit is...
Show More

#Pavid by larry on 2009-07-12 20:14

need any manuals for this gen thx

#Pavid by martha\'s Design Center on 2009-08-30 22:06

Out-put wiring information. Using Generator for back-up power for manufacturing business. Power 3 phase...

#Pavid by Stan on 2010-01-15 23:21

We are looking for a starter motor for a model G18H3 Pavid generator. The serial number is 2227.

#Pavid by Kara Willis on 2010-04-12 15:24

Hello, do you have any information on where I could get Pavid radiator hoses?

#Pavid by Mark Hedden on 2010-09-06 22:15

Hi,I need the same thing. Ihave a 1976 Pavid 35KW 12 wire and I just need to know how to arrange for 240 volt/3 phase. The factory plate says it\'s wired for 139 volt? Sounds wrong, but it\'s the factory plate. Really simple 4 post configuration inside and all the wires are there, but I can\'t figur...
Show More

#Pavid by ROBERTO H DAGNINO on 2011-03-22 18:54

I need information about a Pavid generator I need parts for this generator,all the information you got on this

#Pavid by Roberto H Dagnino on 2011-03-22 19:00

I been trying to contact you people a several times,Ineed urgently information about a Pavid generatorModel:J35DWH-DSerial No.:5882/2060Pavid Manufacturing -Co.-Inc.

#Pavid by Roberto Dagnino on 2011-03-28 17:13

I need information about a Pavid/SulliarModel:J35DWH-DHours: Reads 940.4Running Condition:Engine runs ok,generator does not work.Engine:White 4cyl diesel,Serial #VL3441144 D230 X308Measurments:5\'9\"Wide,9\' 6\" Long, 6\' Tall. I appreciate your soon response.Thank you.

#Pavid by Jeff Slayton on 2011-07-19 17:17

I have an engineer interested in learning more about an old Pravid generator system - where were they made? are parts still available?

#Pavid by Cesar Diaz on 2011-07-27 05:48

Hi i\'ve got an old pavid brush less Model # G15 H3 Serial # 4290 Kw 187-15 Volts 139WDC it had been working good now it doesn\'t have any outp ut 120 V and 480 V I was wondering if you had any electrical prints or adavice on tings to check out the Unit thanks Cesar

#Pavid by Roger on 2012-09-16 06:30

I just purchased a pavid backup generator. is there parts or service available anywhere for my pavid?

#Pavid by Duane Miller on 2013-02-18 22:27

We have a Model # 248125, Serial # 1618/s/ng 4023. I need info on this generator, such as natural to lp conversion kit, excitation componennts, manual, and where to get parts for it.Thanks

#Pavid by Wendy Minchow on 2016-11-21 19:25

I needs filter numbers, oil quantity, coolant quantity, and battery size for a Pavid 65kW model 248269 SN 4599 - this is the only information that is available to me. If you have this information please email me at the email address given above. Any help would be greatly appreciated.

#Pavid by Richard Wood on 2017-09-13 18:19

Hi , I need to know if someone can help me with a Pavid 22KW generator

#Pavid by keith smith on 2018-06-25 01:44

A book or parts for a 13k pavid generator.

#Pavid by Scot Campbell on 2020-02-18 01:31

Manuals with control drawings available?

#Pavid by Tim wood on 2020-12-14 21:32

Would be interested in wiring diagram for a pavid genset. Model j18gaw-f. Serial 2378. Thanks

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.