Rittenhouse Service & Repair Forum

I recently moved into a house that has the Rittenhouse All Transistor RCM-1 system in every room. It\'s obvious this system has not worked in a few years, but I want to repair it and keep it with the time of the home. A newer system would take away from it\'s appeal. Is there anyone in the Tulsa, OK area that could help me?Thank you,Candy Cicoria

β€”> Purchase or Repair: Ticket Image

β€” Posted by Candy Cicoria on 2011-07-14

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "Rittenhouse"

If you need your Rittenhouse unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110


Recent 312 Comments

#Rittenhouse by Lynn Villano on 2011-05-06 13:29
but want door bell to continue working. Can we get wiring schematics?

β€”> Purchase or Repair:
#Rittenhouse by chris on 2015-08-27 21:30
I have gone through the trouble shooting I have 16 volts to the main unit just nothing coming out of main unit. like its acting as if there is no voltage. will not power up, no intercom, no radio is it replacement time or can this be repaired relatively cheap?

β€”> Purchase or Repair:
#Rittenhouse by Eric Hoffman on 2007-12-23 04:40
I have just recently purchased a house that has a Rittenhouse Model 7300 Intercom system that does not work. I am trying to find a schematic for it. I know that it is an old system, but would like to use it to monitor my young children. Any help would be appreciated.Thank you.Eric Hoffmanβ€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Lynn Young on 2015-09-20 19:01
Did you locate the 3 coils you were looking for ? I also need one

β€”> Purchase or Repair:
#Rittenhouse by Michael Donnelly on 2012-06-05 13:26
HiI have the above chime box and wish to re assemble it. I took it down for decorating purposes.There is a black/dark blue wire, a yellow wire and a red wire. There is trans, front and rear. My question is what wire goes with what?Many thanks Michael Donnelly

β€”> Purchase or Repair:
#Rittenhouse by dan mazzola on 2017-02-17 16:32
need a sequence timer for a emerson rittenhouse model # 632 631

β€”> Purchase or Repair:
#Rittenhouse by Janice Lopez on 2009-08-12 02:45
I AM LOOKING FOR A DOOR CHIME FOR MY BUSINESS THAT WHEN SOMEONE ENTERS THE FRONT DOOR THAT I WILL BE ABLE TO HEAR THE CHIME IN OTHER AREAS OF MY BUILDING AS WELL. I NEED SOMETHING THAT WILL HAVE A LOUD CHIME BECAUSE MY BUILDING HAS MACHINERY RUNNING ALL THE TIME. CAN YOU SEND ME SOME INFORMATION. TH…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Donald Brown on 2017-07-07 23:15
I need to have a bulb replacement performed on a 1980ties vintage bronze doorbell. The spring works fine but light nolonger stays on.Regards, Don

β€”> Purchase or Repair:
#Rittenhouse by Charles Cheshire on 2018-07-13 22:04
Cannot reset time seems stripped.Only two of the chimes work.Where are you physically located.ROUGH repair cost.

β€”> Purchase or Repair:
#Rittenhouse by Jeff Picha on 2011-12-05 14:24
Hello, I have a customer that brought in a door bell unit, the one of theplungers is bent inside. I do not know alot about these things, we work on electric motors. He want to know if he can still get parts for these unit.The model # is c8231. Please inform, I may just send him your way. Thanks for …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Earl Miller on 2012-10-11 01:03
Can I use the existing wiring and recessed wall areas of the old system listed above with a new replacement system. If so, what new updated system will work? Thanks

β€”> Purchase or Repair:
#Rittenhouse by Don Heeter on 2017-01-17 21:38
Dear Sirs, I have a Model RM-2.It was put in when the house was built in 1966.It does not work.Thank you for your help.

β€”> Purchase or Repair:
#Rittenhouse by Warren Williams on 2020-04-18 04:45
4 Chime Doorbell With Clock .I Need Instriution Manual and wiring DiagramArtolier Lighting & Sound Div. Emerson Electric Co. Rittenhouse Operations Honeoye Falls NY 14472 Model C8633

β€”> Purchase or Repair:
#Rittenhouse by Bil Hoag on 2015-11-11 17:58
Installed in 1987 when we built the house. Has begun sporadic multiple, single dings, all hours, day and night. I have replaced, back up battery and fuse in motor. Now makes a fairly loud buzzing sound also. Thoughts?

β€”> Purchase or Repair:
#Rittenhouse by Ron Abrams on 2009-02-18 02:03
I\'m working on a unit which has been in the family for years.Emerson- Rittenhouse RC 633, 16 voltOne of the solenoid/hammers don\'t work. Seems that the hammer is jammed in the tube. I\'d like to replace the solenoid. How may I order another one.Ron 305 803-5441

β€”> Purchase or Repair:
#Rittenhouse by arnny on 2009-04-14 22:14
I need a power suply for my Emerson-Rittenhouse model RC 633

β€”> Purchase or Repair:
#Rittenhouse by John Zeitler on 2012-12-05 22:32
I am looking for the cover that is a black plastic 8 3/8\" wide, 5 1/2\" high, and 2 1/8\" deep. Any idea where I can find a suitable replacement? Thanks.

β€”> Purchase or Repair:
#Rittenhouse by Dorothy \"Ann\" Imhoff on 2014-10-23 22:17
A Rittenhouse model 312 came with my home. It works but the chimes are not loud enough to heard unless you are in the room where the doorbell is mounted.I would hate to replace it because other than this it is very workable.

β€”> Purchase or Repair:
#Rittenhouse by Andrew Lazazzera on 2018-02-05 18:04
Have Model DS-2 Door Sentry w/ 16v. chime transformer -Rittenhouse #30 or = need local chicagoland technician to trouble-shoot the control box w/ its transformer.-believe transformer is problem.

β€”> Purchase or Repair:
#Rittenhouse by Howard Robertson on 2012-11-19 01:59
intercom system does not work.would like to have it repaired.

β€”> Purchase or Repair:
#Rittenhouse by peter oliver on 2009-07-16 23:50
I am looking for a remote button for this system.Would possibly trade a receiver unit as I have extra.

β€”> Purchase or Repair:
#Rittenhouse by vero cho on 2007-06-19 19:49
sheetrocking my house after it was flooded by katrina, the contractor stupidly threw away the master station to my doorbell/radio/intercom system which rendered the system inoperable. i have asked an electrician friend to look at it and he cannot find a suitable retrofit. we will have to replace the…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Tom Gleason on 2011-03-31 01:27
Looking for a sequencer box for a model 552 doorbell chime. I know they are rare. Does somebody make a retro fit or do you have a good used one. If none of the above then how about schemetics and I will get one made. Thanks-Tom

β€”> Purchase or Repair:
#Rittenhouse by Gord on 2011-11-24 21:00
Jessica:I have the same model door chime, with the same problem. How did u make out with yours? Do you know any of the history of this chime. From what I can surmise, it was produced after WW2 and that would fit as it was in my parents house when i was born in 1954. I have a friend that is an electr…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Mark Danko on 2015-09-10 19:17
Hi, need repair to this unit, sound cuts in and out when volume control knob is turned/wiggled. Moving molex 5 pin connector on circuit board also causes power to cut in and out. Mode delector knob has become stiff to operate. Please send estimate if repair is possible, thanks

β€”> Purchase or Repair:
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal screw as label…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by dominic Carini on 2009-07-28 00:55
Ihave about a 30 year old rittenhouse with 4 chimes.It seems that the solenoids that activate the strikers,are getting a little lazy.I have had one apart and try to clean it ,with not much succes,I even lost one of those tiny springs. I tried to replace it with a similar one ,but it\'s not right.Do …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by radu munteanu on 2022-04-20 17:35
Good day, I would need the wiring diagram for a Rittenhouse Clock Model 631/632. Just saved the clock from our old house before remodel and we want to install it back with a running clock and the chime.Thank youRadu 650-450-4806

β€”> Purchase or Repair:
#Rittenhouse by Robin Campbell on 2017-09-10 05:21
I have a Rittenhouse master model 550 and 551 doorbell to be tested and repair if needed.

β€”> Purchase or Repair:
#Rittenhouse by Jamie Wingler on 2009-08-30 05:41
I have an inoperative Rittenhouse Model 7021 intercom system as well. Can I fix it or do I have to buy new?

β€”> Purchase or Repair:
#Rittenhouse by Terri McDougall on 2012-04-06 14:55
Our house was built in 1978 and we purchased it in 1997. It had the Rittenhouse monitor system in place with the main unit in the kitchen and smaller units scattered thought the house and in an attached apartment. The unit has never worked since we have been here and I was wondering if it is repaira…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by macgretz on 2017-04-19 20:58
I have a Rittenhouse Emerson Elec Model C8326 (perhaps 1960's) that has stopped working today. The chimes and housing seem okay, but the mechanism and bell button are old and worn out. Do you have replacement parts - and at what cost?

β€”> Purchase or Repair:
#Rittenhouse by Marcy Berry on 2011-03-03 21:25
I am a property manager who manages a townhome with a broken Rittenhouse intercome system. The speakers on the exterior are installed in the brick so to remove them is a huge project. The main console in the kitchen is what I am looking to repair or replace. The model number is: (looks like) M7034. …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by karen varel on 2011-09-07 00:53
Do you sell parts for rittenhouse dooor chimes specifically Model #C8550 or do you know where I can get them?

β€”> Purchase or Repair:
#Rittenhouse by Sandra on 2015-02-13 19:13
Our old doorbell cover on our doors is broken, how and where can we find new or different( maybe clear plastic cover) for the doorbell Thank you

β€”> Purchase or Repair:
#Rittenhouse by Sharon on 2016-11-27 00:16
we have an old rittenhouse intercom system. the units look old but still works fairly well. need information on how to update system. we're remodeling in some areas and would like to check out updating units. don't have specs on the system. not sure of specs but Name on the system is Ritte…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Delia Castillo on 2008-07-29 03:14
we bought this house with installed system. not working. power source not found.

β€”> Purchase or Repair:
#Rittenhouse by Snidal on 2015-08-12 07:20
Please provide an update on the status of the Rittenhouse C8578-1 135-7351-01 door chime unit. It is still not functioning, and we need attention on this matter soon. Thank you.

β€”> Purchase or Repair:
#Rittenhouse by Sylvia on 2016-02-03 03:15
4 out of 10 times whenever I press the button it works.How do I know if the transformer that needs replacement or if the wiring itself that went wrong? I have replaced the button and it should not be the problem itself.How much would it cost if you send someone to fix it?Thanks.β€”> …Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Bob Hilsher on 2010-03-27 16:29
Unit stopped working. Have 16+ volts coming to it but no sound. Assume the syncronous motor is out... Telechron model M3151, Type H18, 3.6 rpm, 60 cy, 16 v. Is the replacement motor available? Price?Could it be anything else? All wiring is in tact on board.Thanks, Bob

β€”> Purchase or Repair:
#Rittenhouse by Harry Yagi on 2017-05-11 12:40
Due to the worn-weakened spring on the hitting bar which do not pop out from the solenoid hole. Do you sell the spring or the entire solenoid with the hitting bar?

β€”> Purchase or Repair:
#Rittenhouse by Ellen on 2011-12-23 17:22
The installation manual has been misplaced and I am not sure which wires go to which connection. There is a red wire, a black wire, and a yellow with a green wire. The places to connect are for the front, rear, and transformer. Please advise. Also, there is a possibility that the transformer doesn\'…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Colleen Wilkowski on 2011-04-28 15:24
I am searching for a User Manual for the Rittenhouse M9041 AM/FM Radio-Intercom system. The unit is original to the house built in 1982. I have found a tech manual with schematics but now need to locate a User Manual. Any suggestions would be appreciated. Thanks.

β€”> Purchase or Repair:
#Rittenhouse by GUY DALFINO on 2013-01-24 17:30
I THINK I NEED A TRANSFORMER CLOCK WLL NOT RUN TX IN ADVANCE gUY

β€”> Purchase or Repair:
#Rittenhouse by Melvin Chrisman on 2007-02-24 22:05
I have a radio intercom unit that needs to be updated.

β€”> Purchase or Repair:
#Rittenhouse by Bob Murley on 2014-10-31 04:57
Is the volume of the chime adjustable?

β€”> Purchase or Repair:
#Rittenhouse by stan Mc Neely on 2014-02-21 17:39
some ONE TOOK MY 577 Apart, I need a picture of how the Chimes goback on the unitTHANKS

β€”> Purchase or Repair:
#Rittenhouse by Donna Dodson on 2007-03-02 16:22
I would like to see if I can get this to work. But I don\'t know where to start.

β€”> Purchase or Repair:
#Rittenhouse by J. G. Colbert on 2010-09-28 22:30
The rheostat is broken on this unit otherwise the unit is as melodious as it was 40 years ago.The numbers on the rheostat are 1406417 and 135-51 The motor is a Telechron synchronous motor. 118V--16 Model 3151 RPM 3. W. 4.CantI purchase the replacement rheostat and have it shipped to PMB 399 at the a…Purchase or Repair: Ticket Image...
Show More
#Rittenhouse by Glenn Loiselle on 2012-08-09 11:58
I have a circa 1977 Artolier Lighting and Sound door Chimes / door bell / wall clock that HUMMS all the time. MODEL # C8633Can it be repaired?

β€”> Purchase or Repair:

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.